Tennant 6100 Instruction Bulletin
Hide thumbs
Also See for 6100:
- Operator's manual (76 pages) ,
- Instruction bulletin (7 pages) ,
- Operator's manual (74 pages)
Advertisement
INSTRUCTION BULLETIN
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE:Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 377411
SYNOPSIS / PROBLEM:
This kit contains the parts needed to replace the brake linkage on 6100, 7100, and EZ Rider
machines.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: Floor jack or chain hoist
(Estimated time to complete: 2 hours)
PREPARATION:
1. Park the machine on a clean level surface.
2. Turn off machine, remove key, and set
parking brake.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, set parking
brake, turn off machine, and remove key.
3. Disconnect the battery cables from the
batteries.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.
4. Block the rear wheels of the machine.
FOR SAFETY: When servicing machine, block
machine tires before jacking up machine.
5. Use a jack to raise the front end of the
machine. Refer to Operators Manual for more
information about safely jacking up the
machine.
FOR SAFETY: When servicing machine, use a
hoist or jack that will support the weight of
the machine.
IB 340763 (11-2005)
FOR SAFETY: When servicing machine, jack
machine up at designated locations only.
Support the machine with jack stands.
INSTALLATION:
1. Loosen both hex screws securing the steering
assembly housing to the machine frame.
Refer to Fig. 1.
Loosen
FIG. 1
2. Slide the steering assembly housing toward
the rear of the machine to loosen the steering
chain tension.
No. 340763
Machine: 6100/6100E/
7100/EZ Rider/7080
Published: 11-2005
Rev. 01
Loosen
Slide entire
assembly
towardsrear
of machine
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tennant 6100
Summary of Contents for Tennant 6100
- Page 1 NOTE:Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials. Installation instructions for kit number 377411 SYNOPSIS / PROBLEM: This kit contains the parts needed to replace the brake linkage on 6100, 7100, and EZ Rider machines. Please follow step-by-step instructions.
- Page 2 3. Remove the master link from the steering 5. Remove the power wire cover from the side of chain and remove the steering chain from the the drive assembly. Refer to Fig. 4. machine. Refer to Fig. 2. FIG. 5 FIG.
- Page 3 8. Remove the hardware (A) securing the brake 13. Use the bolts (L) and hex nuts (M) to install pedal assembly (B) to the machine. Set aside the compression spring (P) and spring all loose parts. Refer to Fig. 8. mounting channel (N) onto the new brake mounting channel (1).
- Page 4 23. Use the master link to reinstall the steering chain onto the machine. Refer to Fig. 14. FIG. 14 FIG. 12- -Newer Machines 24. Push the steering housing forward in the slots and tighten the hex screws to 37--48Nm 17. Remove the upper brake link (U) and brake (26--34 ft.
- Page 5 26. Use hardware (A) to reinstall the brake 30. Reconnect the wires to the drive motor. Refer pedal assembly (B) onto the machine. Refer to Fig. 19. to Fig. 17. FIG. 19 31. Reinstall the power wire cover onto the side of the drive assembly.
- Page 6 377411 Kit, Repmt, Brake Linkage 1019764 Bracket, Channel, Mtg, Brake 1026028 Link, Brake, Upper 1026017 Channel, Brake [6100] 29558 Pin, Clevis, 0.37 D X 1.50L 39005 Pin, Cotter, .094 X 0.75 TENNANT COMPANY P. O. Box 1452 Minneapolis, MN 55440-1452...
Need help?
Do you have a question about the 6100 and is the answer not in the manual?
Questions and answers