1. Manuals
  2. Brands
  3. ClearWater Lights Manuals
  4. Motorcycle Accessories
  5. Glenda
  6. Installation manual

ClearWater Lights Glenda Installation Manual

Ktm 1290 super adventure, led light kit
Hide thumbs Also See for Glenda:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Glenda and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ClearWater Lights Glenda

Summary of Contents for ClearWater Lights Glenda

  • Page 2 Step 1: Parts List and Bike Preparation Please be sure to read our instructions thoroughly before attempting installation. • Check Parts list below with your kit to be sure all parts are handy. If something is missing, please call us at (916) 852-7029. 1290 SA Fender Mount Parts List M5 x 45 (4)
  • Page 3 Step 1: Parts List & Bike Preparation **NOTE** This page is for the 1290 Super Adventure R only Page 3 Page 2...
  • Page 4 D74/G74 Fender Kit Please take the time to review the included instructions. Installation of your new Clearwater Lights is straightforward. But, be sure to follow some of the suggestions to keep the installation safe and reliable. If you have any questions or comments, please feel free to contact us.
  • Page 5 Gently screw all bolts in hand tight. Inspect the bolt length and spacer alignment before tightening the bolts. This location is only for Glenda and Darla lights. D74/G74 Fender Kit Page 5...
  • Page 6 Step 2: Mounting The Lights / Crash Bar Mount Mounting The Lights: (Crash Bar) Mounting the Lights to the Crash Bar is very simple. Pre- assemble the lights, and mounting bracket loosely with the supplied parts. Locate where you would like the light to be pointing and the orientation of either on top or hanging below the bar.
  • Page 7 Step 1: Parts List and Bike Preparation Step 3: Disassembly Disassembly Step 2 Step 1. Remove windshield (T30 x 4) Step 2. Remove windshield bracket (T30 x 4) Step 3. Remove side covers (T30 x 3) Disconnect fog lights Step 4. Remove tank cover (T30 x 5) and (8mm Bolt Location bolt x 2) Step 1...
  • Page 8 Step 3: Disassembly Disassembly Step 5. Remove turn signal covers (T30 x 2) Make note that these bolts are longer than the rest Step 6. Remove headlight (T30 x 4) Disconnect headlight connector, this is the connector that is going to have the jumper in between Step 7.
  • Page 9 Step 3: Disassembly (1290 Super Adventure R, 2017+) **NOTE** This page is for the 1290 Super Adventure R only Headlight guard Fig. A Remove the headlight guard shown above in (Fig. A) It is held down by (2) bolts. Headlight assembly T30 bolt Fig.
  • Page 10 Step 3: Disassembly (1290 Super Adventure R, 2017+) **NOTE** This page is for the 1290 Super Adventure R only T30 bolt Headlight adjuster knob T30 bolt Fig. D The headlight assembly is also held down by the bolts shown above in (Fig. D). Remove the top torx bolt (shown above on the left, but also on the right), the lower torx bolt, and the headlight adjuster knob.
  • Page 11 Once you feel comfortable with the information below you are ready to begin the electrical portion of the installation. Be sure to keep this diagram handy to reference throughout the installation. KTM 1290 SA Glenda/Darla Wiring Diagram Page 11 Page 10...
  • Page 12 Step 4: Wiring (1290 Super Adventure R 2017+ ) **NOTE** This page is for the 1290 Super Adventure R only KTM 1290 SA R Page 12 Page 11...
  • Page 13 Step 4: Wiring Mounting The Control Knob: (Bar Mount) • Mount the Volume Control Knob to handlebar by using supplied bracket and bolt to the existing controls. • Route wires from lights and volume control knob bracket to area under left side of forks. Connections can be made here and be kept weatherproof.
  • Page 14 Step 4: Wiring (1290 Super Adventure R 2017+ ) **NOTE** This page is for the 1290 Super Adventure R only Headlight Connector Fig. F Locate the connector that was plugged into the headlight assembly (Shown above in Fig. F). Connect the included jumper plug to the male and female ends of the headlight connector on the bike.
  • Page 15 Step 4: Wiring Electrical: • Run the Red and Black power wires directly to the battery. The fuse will protect the system in the event of a short. • Mount the power relay box in a safe location (see photo below for one recommended location).
  • Page 16 Step 5: Alignment / Drip Loop Instructions Aligning The Lights: Being that Glenda’s or Darla’s are designed as auxiliary lights, adjustment is up to the user depending on his or her needs. Ask an assistant to help you with this procedure. Make sure the bike is on level ground and have an assistant sit on the bike.
  • Page 17 Notes: Page 17 Page 16...
  • Page 18 Notes: Page 18 Page 17...
  • Page 19 Notes: Page 19 Page 18...
  • Page 20 Version 1.7 12/7/17...

This manual is also suitable for:

Daria

Table of Contents