7.7.16 To connect the electrical meters ........40 6.2.1 Installation site requirements of the outdoor unit ..21 7.7.17 To connect the alarm output ........41 Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Symptom: The compressor does NOT start (space injury. heating or domestic water heating)......73 12.3.3 Symptom: The pump is making noise (cavitation) ..73 12.3.4 Symptom: The pressure relief valve opens....74 EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
(on top of the ▪ In places where there is a risk of fire due to the leakage of instructions described in the Daikin documentation). flammable gases (example: thinner or gasoline), carbon fibre, ignitable dust.
▪ Charge the refrigerant in liquid form. Adding it in gas form may providing full disconnection under overvoltage category III prevent normal operation. condition, MUST be installed in the fixed wiring. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Daikin website (publicly accessible). ▪ Over-tightening the terminal screws may break them. ▪ The full set of latest technical data is available on the Daikin extranet (authentication required). Install power cables at least 1 metre away from televisions or radios to prevent interference.
3.2.3 To remove the accessories from the Outdoor unit outdoor unit 1 Open the outdoor unit. 3.2.1 To unpack the outdoor unit EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ To be able to use the option box, it is required that 3.3.1 To unpack the control box optional control box EKCB07CAV3 is part of the system. 3.4.1 To unpack the option box Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
When installing or servicing several units at the same time, Optional make sure NOT to switch the service panels between different models. Control box Capacity class Model series EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
The user interface and a possible additional user interface are heated. available as an option. ▪ To have an interface containing other languages. The additional user interface can be connected: Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
For installation instructions, see "7.7.7 To connect the user Heat pump convector (FWXV) interface" on page 37. For providing space heating/cooling, it is possible to use heat pump convectors (FWXV). EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ If control box EKCB07CAV3 is part of the system, you questions first: can also connect the LAN adapter to the control box. ▪ How many rooms are heated or cooled by the Daikin heat pump LAN adapter for smartphone control (BRP069A62) system? You can install this LAN adapter to control the system via a ▪...
▪ Code: [C-05] condition. thermostat. Benefits ▪ Wireless. The Daikin external room thermostat is available in a wireless version. ▪ Efficiency. Although the external room thermostat only sends ON/ OFF signals, it is specifically designed for the heat pump system. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3...
Page 14
▪ Cooling. Heat pump convectors provide, besides heating ▪ Stylish. capacity, also excellent cooling capacity. ▪ Efficiency. Under floor heating has the best performance with Altherma LT. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ Code: [7-02] Benefits ▪ Cost effective. You do NOT need an additional external room thermostat. ▪ Easy. Same installation as for one room, but with thermostatic valves. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 16
▪ A shut-off valve to prevent hot water supply when the room has INFORMATION no heating demand To increase comfort and performance, Daikin recommends ▪ A shut-off valve to prevent condensation on the floor during to install the valve kit option EKVKHPC on each heat pump cooling operation of the rooms with heat pump convectors.
NOTICE ▪ Main zone = Zone with the lowest design temperature in heating, Daikin is NOT responsible for the operation of the mixing and the highest design temperature in cooling valve station pump. It is the responsibility of the installer to guarantee pump operation.
▪ If energy prices are the same during the day and the night, Answer the following questions and calculate the DHW consumption Daikin recommends to heat up the DHW tank during the day. (equivalent hot water volume at 40°C) using typical water volumes: ▪...
Heater element (field supply) Non‑return valve (field supply) The calculated produced heat and consumed energy are Shower (field supply) an estimation, the accuracy cannot be guaranteed. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
ALL power input of the system is covered by the of each power meter. electrical power meters. ▪ See "5.4.4 Preferential kWh rate power supply" on page 21 an example with two power meters. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
6 Preparation ▪ If this is NOT possible, Daikin recommends to connect a remote 5.4.4 Preferential kWh rate power supply indoor sensor (option KRCS01-1). General rule ▪ Setup: ▪ Power meter 1: Measures the refrigerant part of the outdoor unit. ▪ Requires...
▪ Where the voltage fluctuates a lot ▪ In vehicles or vessels ▪ Where acidic or alkaline vapour is present Snow cover or shed Pedestal Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ Piping length. It is recommended to avoid long runs of piping between the domestic hot water tank and the hot water end point (shower, bath,…) and to avoid dead ends. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ Air vents. Provide air vents at all high points of the system, which must also be easily accessible for servicing. The outdoor unit has a manual air purge valve. The backup heater (option) has an Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
7H will be generated (no heating or operation). Minimum required flow rate 20 l/min See the recommended procedure as described in "9.4 Checklist during commissioning" on page 67. Pre-pressure (bar) Maximum water volume (l) EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
6.4.1 About preparing electrical wiring 6.4.3 Overview of electrical connections except INFORMATION external actuators Also read the precautions and requirements in the "General safety precautions" chapter. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
3 (of which 2 are for valve kit shared with those EKMBHBP1 (between of item 10) outdoor unit and control box) User interface User interface Optional equipment Outdoor unit EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Failure to follow this warning may result in electric shock. INFORMATION Do NOT remove the plugs from the front plate of the option 3× box. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
CANNOT freeze. (mm) Make sure not to cover the drain holes. INFORMATION The recommended height of the upper protruding part of the bolts is 20 mm. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
(field supply). box. For more information, refer to "7.7.7 To connect the user interface" on page 37. 4 Attach the ends of the cables and tighten them. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
10 bar must be installed on the Filling the domestic hot water tank (if applicable). domestic cold water inlet connection in accordance with Insulating the water piping. the applicable legislation. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ Protection against freezing: the glycol will prevent the liquid inside the piping from freezing. Lowest expected Prevent from Prevent from outdoor bursting freezing temperature –5°C –10°C –15°C –20°C — –25°C — EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
However, at all times water pressure shall remain above DANGER: RISK OF ELECTROCUTION 1 bar to avoid air entering the circuit. WARNING ALWAYS use multicore cable for power supply cables. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
"7.2.2 To open the outdoor unit" on page 28. 2 Strip insulation (20 mm) from the wires. Strip wire end to this point Excessive strip length may cause electrical shock or leakage. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Preferential power supply contact (on the control box) INFORMATION For the exact position of connectors X6Y, X6YA, and X6YB in the switch box, see the service manual. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
For more information on the backup heater types, and for how to configure the backup heater, refer to the "Configuration" chapter of the installation manual of the outdoor unit. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
To connect the shut-off valve 1 Connect the valve control cable to the appropriate terminals as shown in the illustration below. NOTICE Only connect NO (normal open) valves. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
To connect the interconnection cable between control box and outdoor unit 1 Connect X2M/22 (control box) to X5M/4 (outdoor unit). 2 Connect X2M/23 (control box) to X5M/3 (outdoor unit). EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
X2M/7 and X2M/9; the negative polarity to X2M/8 and X2M/10. 1 Connect the electrical meters cable to the appropriate terminals as shown in the illustration below. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
1 Connect the space cooling/heating ON/OFF output cable to the 7.10.1 To close the option box appropriate terminals as shown in the illustration below. 1 Close the front plate. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
To set the user permission level to Advanced end user 1 Go to the main menu or any of its submenus: 2 Press for more than 4 seconds. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
If a second user interface is connected, the installer must first proceed below instructions for the proper configuration of the 2 user interfaces. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
When the installer settings are changed, the system will request to confirm. When confirmation is complete, the screen will shortly turn OFF and "busy" will be displayed for several seconds. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 45
▪ b: OFF ▪ c: On ▪ c: On ▪ d: Heating demand (by ext RT or ▪ d: Pump operation continued >> ▪ e: Pump operation EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Control box INFORMATION The correct domestic hot water default settings become only applicable when domestic hot water operation is activated ([E‑05]=1). Remote outdoor sensor "5 Application guidelines" on page 12. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 47
▪ 0 (EKHWS): DHW tank with booster heater installed at the side of the tank. (Default). ▪ 5 (EKHWP): DHW tank with booster heater installed at the top of the tank. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Remark: This value has only meaning in room thermostat control. INFORMATION You can only connect either the remote indoor sensor or the remote outdoor sensor. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 49
: Target leaving water temperature (main) ▪ T : Target leaving water temperature ▪ T : Outdoor temperature (main) continued >> ▪ T : Outdoor temperature continued >> EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 50
[0-00] Set weather-dependent heating: [0-01] [0-02] [0-01] [0-03] [0-00] [0-03] [0-02] ▪ T : Target leaving water temperature (additional) ▪ T : Outdoor temperature continued >> Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 51
The unit will supply hot water to the heat emitters and the room will be heated. Additionally, also the desired leaving EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Minimum leaving water temperature setpoint required to reach a stable condition on the comfort setpoint for the Limit the maximum hot water temperature according to the room. applicable legislation. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Preset leaving water temperature for the main leaving water temperature zone in case of NOT weather dependent [7.4.2.1] [8-09] Comfort (heating) [9‑01]°C~[9‑00]°C (default: 45°C) [7.4.2.2] [8-0A] Eco (heating) [9‑01]°C~[9‑00]°C (default: 40°C) EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 54
▪ 2 (enabled) L=4°C, temperature is displayed in °C. R=4°C (−2°C<T <2°C) (default) ▪ 3 (enabled) L=2°C, R=8°C (−4°C<T <4°C) ▪ 4 (enabled) L=4°C, R=8°C (−4°C<T <4°C) Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 55
▪ Turn ON the leaving water temperature home page. Leaving water temperature Room frost protection is NOT control ([C‑07]=0) guaranteed. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 56
22°C and in cooling 24°C, with a hysteresis value of 1°C and an offset of 4°C. Changeover from heating to cooling will occur when the room Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
The tank will then heat up until interface. these setpoint temperatures have been reached. Additionally, a EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 58
▪ Ambient temperature is out of the operating range: <[5-03] >35°C ▪ Domestic hot water temperature is 2°C lower than the heat pump OFF temperature. continued >> Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 59
For more information, see the operation range. Timers for simultaneous request space and domestic hot water operation Code Description [8-00] Do not change. (default: 1) EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 60
The disinfection function settings MUST be configured by temperature [4-02] or [F-01]. the installer according to the applicable legislation. Range: 20~95 minutes (default: 50). [8-02]: Anti-recycling time Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Space heating priority temperature. the auto restart function. Defines the outdoor temperature which below the domestic hot water will be heated by booster heater only. Range: –15°C~35°C (default: 0°C). Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 63
[D‑00] Booster heater Backup heater Compressor <4°C (pump will be activated for 10 minutes and deactivated after 10 minutes). Daikin shall NOT be held liable for any damage 0 (default) Forced OFF Forced OFF Forced OFF resulting this functionality.
Page 64
(kPa) b (l/min) b (l/min) [9-0D]=6 [9-0D]=7 a (kPa) a (kPa) b (l/min) b (l/min) [9-0D]=8 a (kPa) b (l/min) External static pressure Water flow rate Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Set weather-dependent heating Set weather-dependent cooling [7.7.2] Additional Set weather-dependent heating Set weather-dependent cooling INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
[A.7] Commissioning Test run UFH screed dryout Air purge Actuator test run INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
The fuses or locally installed protection devices are The underfloor screed dryout function is started (if installed according to this document, and have NOT been necessary). bypassed. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
To perform an automatic air purge Prerequisite: Make sure that the leaving water temperature home page, room temperature home page, and domestic hot water home page are turned OFF. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
4 Select OK and press Result: The actuator test run starts. It automatically stops when finished. To stop it manually, press , select OK and press EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
2 Set a dryout program. ▪ Explain the user about energy saving tips as described in the 3 Select Start dryout and press operation manual. 4 Select OK and press Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
GWP value of the refrigerant × Total refrigerant charge [in force when you reinsert the water filter so as NOT to kg] / 1000 damage the water filter mesh. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
OFF. WARNING If the internal wiring is damaged, it has to be replaced by the manufacturer, its service agent or similarly qualified persons. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ The expansion vessel is NOT broken. ▪ The pre-pressure setting of the expansion vessel is correct (see "6.3.4 Changing the pre- pressure of the expansion vessel" on page 26). EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
▪ The water pressure ▪ Whether there is air in the system ▪ The air purge operation Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
OU: Malfunction of inverter Please contact your dealer. radiating fin temperature rise. OU: Compressor startup defect. Please contact your dealer. Please contact your dealer. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 76
Room temperature sensor sensor problem. problem. Please contact your dealer. Please contact your dealer. Heat exchanger frozen. Abnormal increase tank temperature. Heat exchanger frozen. Tank preheating Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 77
▪ During anti-legionella operation (weekly), the error code occurred during space heating AH-00 is displayed because the unit cannot reach the operation. Check the space requested temperature required for tank disinfection. heating circuit. EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
You can achieve this, for example, by activating all fans of the fan coil units. INFORMATION For more details, see the service manual. Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
14 Technical data Technical data A subset of the latest technical data is available on the regional Daikin website (publicly accessible). The full set of latest technical data is available on the Daikin extranet (authentication required). 14.1 Service space: Outdoor unit...
See note *** See note *** Main terminal Upper Fan Upper fan Earth wiring Lower Fan Lower fan Field supply Injection Injection Option Main Main Switch box Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 82
Outdoor backup heater power supply 3-way valve for domestic hot English Translation water Only for *** Only for *** Valve kit Backup heater element (3 kW) PC (A7P) Power circuit Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 83
F2U (A4P) Fuse T 2 A 250 V for 3-way valve External indoor ambient sensor option S5P-S6P # Electrical meters X*A (A4P) Connector Terminal strip Optional Field supply EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Installer reference guide Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
If glycol is added to the system, the operation range limit is lower. ▪ Selecting a flow outside the operating area can damage the unit or cause the unit to malfunction. B (l/min) 4D117234 Installer reference guide EBLQ+EDLQ011~016CA3V3+W1 + EK(2)CB07CAV3 Daikin Altherma low temperature monobloc 4P538847-1 – 2018.05...
Page 85
Optional equipment Equipment made or approved by Daikin that can be combined with the product according to the instructions in the accompanying documentation. Field supply Equipment NOT made by Daikin that can be combined with product according instructions accompanying documentation.
Page 87
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value User settings └─ Preset values └─ Room temperature 7.4.1.1 Comfort (heating) [3-07]~[3-06], step: A.3.2.4 21°C 7.4.1.2 Eco (heating) [3-07]~[3-06], step: A.3.2.4 19°C 7.4.1.3 Comfort (cooling)
Page 88
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value A.2.1.8 [7-02] Number of LWT zones 0: 1 LWT zone 1: 2 LWT zones A.2.1.9 [F-0D] Pump operation mode 0: Continuous 1: Sample 2: Request...
Page 89
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value A.3.1.3.2 [9-0A] Cooling 3~10°C, step: 1°C 5°C └─ Room thermostat A.3.2.1.1 [3-07] Room temp. range Minimum temp (heating) 12~18°C, step: A.3.2.4 16°C A.3.2.1.2 [3-06]...
Page 90
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value A.6.C 0: Manual 1: Automatic └─ Overview settings [0-00] Leaving water value for high ambient temp. for LWT add zone heating WD curve. [9-05]~min(45, [9-06])°C, step: 1°C 35⁰C [0-01]...
Page 91
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value [4-03] Operation permission of the booster heater 0: Limited 1: No limit 2: Most optimum 3: Optimum 4: Only legionella [4-04] How to protect the water pipes from freezing 0: Continuous pump operation...
Page 92
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value [8-06] Leaving water temperature maximum modulation. 0~10°C, step: 1°C 3°C [8-07] What is the desired comfort main LWT in cooling? [9-03]~[9-02], step: 1°C 18°C [8-08]...
Page 93
Field settings table Installer setting at variance with default value Breadcrumb Field code Setting name Range, step Date Value Default value [D-04] Is the option box used for PCC ? 0: No 1: Yes [D-05] Is the pump allowed to run if prefer. kWh rate PS is cut? 0: Forced off 1: As normal [D-07]...