Peco Pro2B+ 23120910 Operator's Manual
Pto grass collection system
Hide thumbs
Also See for Pro2B+ 23120910:
- Operator's manual (12 pages) ,
- Operator's manual (34 pages) ,
- Operator's manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco Pro2B+ 23120910
Summary of Contents for Peco Pro2B+ 23120910
- Page 1 P P P P P P P PTO GRASS COLLECTION PECO PECO PECO PECO PECO PECO SYSTEM MODEL# 23120910 CRZ, XRZ & XRZ Pro 2013-Newer MODEL# 23120911 FastCat RZ 2015-Newer OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0472 REV: 3.0 (June 2017)
-
Page 2: Table Of Contents
RESIDENTIAL BAGGING SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 2-14 Weight Kit Assembly Installation - - - - - - - - - 15-16 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 2-15 Length of Hose Adjustment - - - - - - - - - - - - - - 17... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
1. NO SERVICE CENTER WARRANTY The selling Service Center makes no warranty on his own on any item warranted by New PECO, Inc. unless he delivers to purchaser a separate written warranty certificate specifically warranting the item. The dealer has no authority to make any representation or promise on behalf of PECO or to modify the terms of this warranty in any way. -
Page 5: Introduction And Description
Remove the D-drive spacer using an arbor press or Section I equivalent. On removal, adjacent bearing OUTER race must be supported or bearing damage may occur. Refer INTRODUCTION & DESCRIPTION to Figure 2-1b. 1-1 Introduction PRESS Your grass collection system has been designed to give Figure 2-1b you a low maintenance, simple, and effective way to collect the grass clippings from your mower. -
Page 6: Left & Right Frame Bracket Installation
Secure the left frame bracket P#(B0837) to the mower 2-2 Left and Right Frame Bracket rear frame using (3) 3/8”-16 x 1” HHCS P#(K1191) and Installation (3) 3/8”-16 nylon flange locknut P#(K2038). Leave the hardware slightly loose until all the frame components are installed. -
Page 7: Rear & Lower Frame Bracket Installation
2-3 Rear Frame Bracket and Lower Frame Bracket Installation Secure the rear frame bracket P#(B0855) to the inside of Secure the lower frame bracket P#(B0838) to the inside the left and right frame bracket using (2) 3/8”-16 x 1” of the left, right and rear frame bracket using (4) 3/8”-16 HHCS P#(K1191) and (2) 3/8”-16 nylon flange locknuts x 1”... -
Page 8: Pto Mount Plate Component Installation
2-4 PTO Mount Plate Component Installation Insert the PTO stop plate P#(B0733) between the left Fasten the left PTO mount plate P#(B0748) the right and right PTO mount plates as shown in Figure 2-4b. frame bracket using (2) 3/8”-16 x 1” HHCS P#(K1191) Secure the PTO stop plate to the left and right PTO and (2) 3/8”-16 nylon flange locknuts P#(K2038). -
Page 9: Pto Assembly Installation
Loosen the (2) 5/16”-18 x 3/4” HHCS P#(K1153) that 2-5 PTO Assembly Installation secure the gear box to the PTO assembly, as shown in Figure 2-6b. Loosen the adjustment bolt (1) 3/8”-16 x 2” hex bolt P#(K0348). Insert the PTO assembly P#(A1840) into the mounting slots on the PTO mount plates, as shown in Figure 2-5. - Page 10 2-6 Belt Installation and Adjustment and Pulley Guard Installation Figure 2-6d Continued... (1) 3/8”-16 x 1” Hex Bolt Secure the top belt guard P#(B0862) tot he right frame (1) 3/8”-16 Locknut bracket using (1) 3/8”-16 x 1” HHCS P#(K1191) and (1) 3/8”-16 nylon flange locknut P#(K2038) from the mount kit hardware bag, as well as (1) 3/8”-16 x 1”...
-
Page 11: Blower Cone Installation
2-7 Blower Cone Installation 2-8 Impeller Blade Removal/Replacement Fasten the blower cone P#(V0016) to the blower housing located on the PTO assembly. Use (3) 1/4”-20 x 3/4”HHCS P#(K1222), (3) 1/4” lock washers P#(K0039), To Remove: To access the impeller blade, remove the and (3) 1/4”... -
Page 12: Lower Mount Tube Installation
2-9 Lower Mount Tube Installation Position the lower mount tubes P#(B0752) on top of the (4) 5/16”-18 two tabs on the rear frame bracket. Secure each lower Locknuts mount tube using (2) 5/16”-18 x 2-1/4” u-bolts P#(K1098) (PER TUBE) and (4) 5/16”-18 nylon flange locknuts P#(K2516) PER TUBE. -
Page 13: Top Assembly Installation And Inlet Installation
2-11 Top Assembly To Upper Frame 2-12 Hinge Kit Assembly Installation Assembly Installation & Inlet Assemble the hinge kit as shown in Figure 2-12, using Installation (2) 5/16”-18 x 1” HHCS P#(K1154), (3) 5/16”-18 nylon flange locknuts P#(K2516), (5) 1/4” flat washers Position the top assembly P#(A2101) above the upper P#(K0037) and (2) swing arm brackets P#(ZT-0004). -
Page 14: Boot To Mower Deck Installation
2-13 Boot To Mower Deck Installation Secure the boot plate P#(B0807) to the top surface of the plastic boot P#(V1173) using (3) 5/16”-18 x 3/4” carriage bolts P#(K1142) and (3) 5/16”-18 nylon flange locknuts. Insert the carriage bolts from the inside so that the threads and locknuts are on the top of the boot plate. -
Page 15: Weight Kit Assembly Installation
2-14 Weight Kit Installation / Left Caster To Install Weight Bracket Step 1 - Position (#2) Base Under Caster Tubing w/ Opening Towards Caster Fork. Step 2 - Position (#3) Clamp On Top Of Caster Tubing w/ Opening Towards Caster Fork. Step 3 - Align (4) Holes In (#3) Clamp To Holes In (#2) Base Step 4 - Loosely Fasten (#3) Clamp To (#2) Base Using... - Page 16 2-14 Weight Kit Installation / Right Caster To Install Weight Bracket Step 1 - Position (#2) Base Under Caster Tubing w/ Opening Towards Caster Fork. Step 2 - Position (#3) Clamp On Top Of Caster Tubing w/ Opening Towards Caster Fork. Step 3 - Align (4) Holes In (#3) Clamp To Holes In (#2) Base Step 4 - Loosely Fasten (#3) Clamp To (#2) Base Using...
-
Page 17: Length Of Hose Adjustment
2-15 Length Of Hose Adjustment 2-17 Lower Hose To Blower Cone The hoses in steps 2-16 and 2-17 must be cut to fit your Installation machine. Follow steps 2-16 and 2-17. do not cut the Slide a pre-assembled hose clamp P#(J0060) over both hoses until you have tried to fit them on your machine. -
Page 18: Bag Assembly
2-19 Bag Assembly First, take one of the Bag Ring Split Ends and insert it through the Bag Seam Opening. Next, rotate the Bag around the Bag Ring (1) full turn (360 degrees) until the Bag Ring Split Ends and the Bag Seam Opening are positioned on the same side. -
Page 19: Operating Instructions
Disengagement Of The PTO Assy. SECTION III - P2B OPERATING INSTRUCTIONS A. To disengage the PTO assembly, slide the engagement handle out of the retaining slot and push the engagement handle away from the operator’s General Safety seat. Only qualified people familiar with this operator’s manual WARNING: The PTO assembly blades will continue to and the mower’s operator’s manual should operate this spin. -
Page 20: Lubrication
If for any reason your Service Center 4. Check belt for proper tension. is unable to service your collection system or supply replacement parts, contact New Peco Inc. and include the following information on the chart below. DOCUMENT THE FOLLOWING INFORMATION FOR FUTURE REFERENCE... - Page 23 TOP ASSEMBLY EXPLODED PARTS VIEW Item # Part # Desc. Qty. V2000 Pro 2 Bagger Top / Gen. 2 V2001 Screen J4009 Short Rubber Strap w/ S-Hook K1030 1/4"-20 x 1-1/4" Carriage Bolt K0037 Flat Washer / 1/4" (.75 OD x .312 ID x .060 T) K1128 1/4"-20 Nyloc Nut K0062...
- Page 24 A1840 PTO ASSEMBLY EXPLODED PARTS VIEW DESCRIPTION...
- Page 25 A1840 PTO ASSEMBLY EXPLODED PARTS VIEW Item # Doc # Title M0266 'A' PULLEY FOR DECK DRIVE PTO K1446 1.187 OD x .380 ID x .187 WASHER k1190 3/8"-16 x 3/4" HHCS V0015 BLOWER HSG. A0431 GEAR BOX A0498 PULLEY ASSY. FOR GEAR BOX K0360 7/8"...
-
Page 26: Safety Decals
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. PUSH HANDLE DISENGAGE DISENGAGE Part# R0022 Designed &... -
Page 28: Troubleshooting
Troubleshooting Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace — Impeller blade out of balance —... -
Page 29: Notes
NOTES... - Page 30 P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...