Grass collection system for country clipper avenue 42”-54” & boulevard 48”-54” 2015-newer (20 pages)
Summary of Contents for Peco PRO-12 41721209
Page 1
P P P PRO 12 PECO PECO PECO PECO PECO GRASS COLLECTION SYSTEM MODEL 41721209 & 41721215 FERRIS IS 3100Z SERIES MOWER OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0406 $10.00 REV: 1...
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later.
1-1 Introduction Rear Guard Removal Figure 2-1a We are pleased to have you as a PECO customer. Your collection system has been designed to give you a low maintenance, simple and effective way to collect the grass clippings from your mower. This manual is...
2-3 Lower Stiffener Installation Main Frame Figure 2-5 Assembly Attach the lower stiffener P#(B0611) to the left and right lower main frame legs, using (4) 3/8”-16 x 1-1/4” HHCS P#(K1192) and (4) 3/8”-16 nyloc nuts P#(K1216). Refer to Figure 2-3. Figure 2-3 (4) 3/8”-16 x 1-1/4”...
2-8 Engine/Blower/Blade Assembly 2-10 Aluminum Grass Container Installation Installation Position the engine/blower/blade assembly on top of the NOTE: It is recommended that (3) people assist in engine mount arm assembly and secure using (4) 5/16”- mounting the container. 18 x 1-1/2” HHCS P#(K1157) and (4) 5/16”-18 nyloc nuts P#(K1180).
2-12 Blower Cone Installation 2-13 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the 3/8”-16 x 1-1/2” HHCS thread the bolts into each of the two tabs located on the P#(K1211) (#1), taper lock bushing washer P#(K0278) blower housing.
2-14 Throttle Cable Installation Figure 2-14d To install the throttle cable kit P#(A0060 for 5.5HP) or P#(A0294 for 6.0 HP) to the box assembly, align the large end of the slot in the throttle base plate (Figure 2- 14a) with the rivets located on the front of the box assembly frame (Figure 2-14b).
2-15 Boot To Mower Deck Installation 2-18 Lower Hose Installation Fasten the boot plate P#(B0612) to the boot P#(E2502) Slide a lower hose clamp P#(J1000) onto both ends of using (2) 3/8”-16 x 1” carriage bolts P#(K1182), (2) 3/8” the 8” lower hose. Slide one end of the lower hose onto flat washers P#(K0047), and (2) 3/8”-16 nyloc nuts the blower cone, with 2”...
Page 14
P P P P P P P MODEL#: 41721215 PECO PECO PECO PECO PECO PECO MOWER NAME: FERRIS MOWER MODEL: IS 3100Z MOWER DECK SIZE: 61” VAC NAME: PRO 12 FOR YEAR: 2010 6.5HP BRIGGS AND STRATTON VANGUARD REVISED: 10/22/2012...
* Mow twice, at different height settings, (high, then low), been torn or worn through, replace with genuine if grass is extra tall. PECO parts. * Remember that horsepower requirements will vary with the mowing conditions such as type and height of turf...
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PECO collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system.
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1053...