Table of Contents
Advertisement
3. Installation Method
Cautions on installation
•
Use the unit in the environment for the general specifications described in the manual.
Never use the unit in a place with dust, soot, conductive dust, corrosive gas or flammable gas,
a place exposed to high temperature, dew condensation or rain and wind or a place exposed
to vibration or impact.
If the unit is used in such a place, electrical shock, fire, malfunction, damage in the product or
deterioration of the product may be caused.
•
Never drop cutting chips or electric wire chips into the ventilation window of the FX
while drilling screw holes or wiring cables.
Such chips may cause fire, failure or malfunction.
•
After finishing installation, remove a dust preventing sheet adhered on the ventilation window
of the PLC and the FX
If the sheet remains attached, fire, failure or malfunction may be caused.
•
Securely connect connection cables such as extension cables and memory cassettes to specified
connectors.
Imperfect contact may cause malfunction.
The FX
-2LC can be installed on the right side of an FX
2N
extension unit.
The FX
-2LC can be attached with a DIN rail DIN46277 (width: 35 mm) or directly attached to a panel
2N
surface with screws (M4).
3.1 Installation on DIN rail
Align the upper side of the DIN rail mounting groove of the FX
➀
mm) (
), and push it on the DIN rail.(
When removing the FX
➃
rail.(
)
When attached to DIN rail
3.2 Direct installation on panel surface
Screw-tighten the FX
holes provided on the left side of the FX
Assure the interval of 1 to 2 mm between a unit or block installed on the left side of the FX
4. Connection to PLC Main Unit
Connect the FX
-2LC to the PLC main unit with an extension cable.
2N
FX
-2LC units are treated as special units of the PLC, and the special unit No. 0 to 7 is automatically
2N
assigned to each FX
FROM/TO instructions.)
One FX
-2LC unit occupies eight I/O points in the PLC main unit.
2N
For the details of I/O assignment in the PLC, refer to the manual of the PLC main unit.
FX
-32MR
2N
(X000 to X017)
COM
L
N
24+
X1
FX
2N
Y2
Y4
Y1
Y3
Y5
(Y000 to Y017)
•
Please check power supply specifications to decide the number of FX
to the FX
/FX
1N
2N
•
To connect the FX
•
For extension, an extension cable FX
required. Only one FX
( ) indicates the I/O No.
-2LC.
2N
➁
)
-2LC, pull out downward the DIN rail mounting hook.(
2N
‚
-2LC with M4 screws to a panel surface using two (upper and lower) mounting
2N
2N
-2LC unit from the one nearest to the PLC main unit. (These unit Nos. are used in
2N
FX
-4AD
2N
X2
X4
X10
X14
X16
X3
X7
X13
X15
POWER
0
1
2
3
4
5
6
7
IN
10
11
12 13
14
15
16
17
POWER
RUN
BATT.V
PROG.E
0
1
2
3
4
5
6
7
-32MR
OUT
CPU.E
FX
-4AD
10
11
12 13
14
15
16
17
2N
Y6
Y10
Y12
Y14
COM3
Y11
Y13
Y15
Special block
No. 0
/FX
/FX
extension unit and PLC.
2NC
3U
-2LC unit to the FX
2N
0N
-65EC can be used in one system.
0N
/FX
1N
2N
When removed from DIN rail
-2LC.
FX
-2LC
2N
POWER
FX
-2LC
2N
24V
24V
OUT1
A/D
OUT2
Special block
No. 1
Series PLC, the interface FX
2NC
-65EC (650 mm) and the FX
/FX
/FX
Series PLC main unit or
2N
2NC
3U
-2LC with a DIN rail DIN46277 (width: 35
➂
), and remove from DIN
„
ƒ
FX
-32ER
2N
(X020 to X037)
COM
X0
X2
X4
X6
X0
X2
X4
X6
L
N
24+
X1
X3
X5
X7
X1
X3
X5
X7
0
1
2
3
4
5
6
7
IN
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
FX
-32ER
OUT
2N
0
1
2
3
4
5
6
7
Y0
Y2
Y4
Y6
Y0
Y2
Y4
Y6
COM1
Y1
Y3
COM2
Y5
Y7
COM3
Y1
Y3
COM4
Y5
Y7
Special block
(Y020 to Y037)
-2LC units that can be connected
2N
-CNV-IF is required.
2NC
-CNV-BC sold separately are
2N
-2LC
2N
-2LC.
2N
FX
-2LC
2N
POWER
POWER
FX
-2LC
2N
24V
OUT1
OUT2
No.2
Advertisement
Table of Contents
