How To Modify A Parameter - KEPCO BOP 6-125MG/ME Quick Start Manual

#
•
• •
$
•
• •
%
•
• •
• •
• •
• •
• •
• •

HOW TO MODIFY A PARAMETER.

First access the parameter by accessing the proper
menu as described above. To modify a parameter
listed in a menu or submenu, proceed as follows:
1. Highlight the parameter using the
2. When the desired choice is highlighted, press
to modify the active setting. The choices are dis-
KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A. TEL (718) 461-7000  FAX (718) 767-1102
10
- Display
Display Settings:: Graphic
(meters/graphics, background
white/monoblack/blue/green/lt.green/
lt.blue), Protect Entry (independent/bipo-
lar) Waveform Stop (outputOFF/User
Option), Key Press beep (On/Off/Error
only)
- Analog Remote Setup
Analog Remote Settings: Reference input
(internal/external/external
level), protect limit (Internal/External/Les-
serLimit), external mode (disable/enable)
- General Setup
Interface Settings:
• *RST set Output (on/off),
• GPIB Settings: Language (SCPI/CIIL),
GPIB address (default = 6),
clear (SCPI/MATE)
• Serial Settings: Baudrate (Off/9600/
19200/38400), Xon/Xoff
enable), prompt (disabled/echo/
enabled/enab+echo)
• LAN Settings: IP Address, IP MASK,
AUTO IP ON, DHCP ON, Name and
index (MDNS name)
Max/Min Settings: for voltage mode: +Volt-
age max, –Voltage min, ±CProtect max/
min; for current mode: +Current max,
–Current min, ±VProtect max/min
FIGURE 5. POWER-UP SCREEN SHOWING GRAPHIC METERS
Y
and
http://www.kepcopower.com   email: hq@kepcopower.com
Display
(black/
reference
Device
(disable/
played with the active setting highlighted. In the
case of numerals, the units digit is highlighted.
• To change a numeric setting, press the num-
ber keys, then press ENTER to program the
numbers entered. Use the CLEAR key to
U
keys.
clear numbers entered and start over. The
!
ADJUST control can also be used to incre-
ment or decrement the highlighted digit.
228-1692 REV 8
• • Load Type: Active/Resistive/Battery,
Remote On-off: (disabled/high is off/low is
off/high is on/low is on/LowPulseOff)
• • Standby Pin Operation: LowPulse, HighI-
sOn, LowIsOn, HighIsOff, LowIsOff, Dis-
abled
• • Revisions/Test: (Tests: display, keypad,
LAN, interface, serial, analog and output)
• • Calibration: Voltage, Current and External
and Controls calibration. Shows Firmware
versions for Display, Serial, GPIB, LAN
and analog.
• • Power-up Settings: Mode (Voltage/Cur-
rent/External), Main channel Reference
(Internal/External/ExtlRefLev), main set-
ting, Protection: Type (Internal/External/
LesserLimit), Voltage Limit (current mode),
Current Level (voltage mode), output ON/
OFF
• • Password
• • • Password Settings: Menu protection
(Interface/Max-Min/Load/Test/Calibra-
tion/Power-up/Keypad
pad@power-up), Save Display Change
(Enable/Disable), Passwords (Unpro-
tected/Main/Admin1/Admin2)
• • Series/Parallel: Configuration (Standalone/
Parallel/Series/Master 2X2/Master 3X2);
for parallel or series: Unit Type (Stand-
alone/Master+1 to+4/Slave #1 to #4) and
Configuration: shows Series or Parallel).
@ local/Key-
090418