Accessories; Installation; Input Connections; Load Connections - KEPCO BOP 6-125MG/ME Quick Start Manual

VI — ACCESSORIES.
ITEM
Line Cord (250V, 20A)
Line Cord (250V, 20A)
Mating Connector, Trigger
IEEE 1118 (BITBUS)
Mating connector
IEEE 488 Cable, (1 meter long) For MG models only. Connects BOP power supply to GPIB bus.
IEEE 488 Cable, (2 meter long) For MG models only. Connects BOP power supply to GPIB bus.
IEEE 488 Cable, (4 meter
longs)
Interconnection Kits for parallel/
series configurations.
RS 232 Cable Kit
RS 232 Adapter (Male pins)
RS 232 Adapter (Female pins)
15-pin DSUB Connector
IDC 6-pin connector
IDC 8-pin plug
Slides
Heat Sink
Output Terminal Cover
VII — INSTALLATION.
Install units either on a bench or in a 19 inch-wide
rack. For rack mounting: remove four feet first; rack
must provide support at the rear). Optional slides
may be used. Leave the front and rear panels clear
of obstructions to ensure adequate cooling. For par-
allel, series and master-slave configurations, refer to
the Operator's Manual.
INPUT CONNECTIONS. Source power is con-
nected to the power supply via three-wire input
power using the source power mating connector
supplied (see Table 4). This power supply operates
from single phase a-c mains power (or between two
KEPCO, INC.  131-38 SANFORD AVENUE  FLUSHING, NY. 11355 U.S.A. TEL (718) 461-7000  FAX (718) 767-1102
090418
See Table 4.
TABLE 4. ACCESSORIES
Provides connection to a-c mains via Nema 6-20P connector.
Provides connection to a-c mains via Nema L6-20P locking type connector.
Mates with Trigger port.
Allows connection to IEEE 1118 (BITBUS) port.
For MG models only. Connects BOP power supply to GPIB bus.
Cables required to connect multiple BOP models in parallel, series, or paral-
lel/series configurations.
Contains RJ11 to RJ45 Patch cord, RJ 45 Patch cord, two RS 232 adapters,
one with male pins to connect to DTE equipment and one with female pins to
connect to a PC (personal computer), two RS 232 Loop Back test Connec-
tors (one 6-pin and one 8-pin) to test RS 232 communication and aid in iso-
lating RS 232 communication problems.
Allows RS 232 port to be connected to DTE equipment. (Supplied in KIT
219-0436.)
Allows RS 232 port to be connected to a PC (personal computer). (Supplied
in KIT 219-0436.)
Mating connector for Analog input connector A2A5J6
Mating connector for RS-232 PORT, connector A1J5 and PROTECTION
EXT. PORT, connector A2A5J7
Mating connector for PAR/SER PROTECT PORT (IN and OUT) connectors.
Allows easy withdrawal of unit from rack (see Figure 1). (Model CS 04
includes slides, brackets, all mounting hardware and installation instruc-
tions.)
Provides adequate cooling for calibration sense resistors.
Protects against inadvertent contact with output and barrier strip terminals
http://www.kepcopower.com   email: hq@kepcopower.com
FUNCTION
Dsub 15 pin hood
Dsub 15 pin male
phases of 3-phase a-c mains power), 230V, 50/60Hz
nominal (range: 176 - 264V, 47-63Hz) without any
need for range selection. The user must provide a
properly sized and rated mains lead (line cord) and
service with a current rating compatible with the
anticipated input current. Line cords available as
accessories are listed in Table 4. Plug the source
power connector into the source power inlet connec-
tor at the rear panel.
LOAD CONNECTIONS. Power connections re-
quire wires that are properly rated for the nominal out-
put current of the unit. Connect the load to the OUT-
228-1692 REV 8
PART NUMBER
118-1087
118-1088
142-0527 (Kepco)
SP2501 (CUI Stack)
142-0485 (Kepco)
KMDLA-5P (Kycon Inc.)
SNC 488-1
SNC 488-2
SNC 488-4
See Operator's Manual.
KIT 219-0436
142-0487
(L-COM RA098M)
142-0506
(L-COM RA098F)
108-0374
(Tyco-Amp 207470-1)
142-0449
(Amphenol 17S-DA15P)
142-0536
(Amphenol 5-555176-3)
142-0535
(Amphenol 5-555176-3)
CS 04
136-0451
129-0423
5