IEI Technology TANK-870AI SERIES User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Industrial PC
  5. TANK-870AI SERIES
  6. User manual

IEI Technology TANK-870AI SERIES User Manual

Embedded system with 6th generation intel core processor 8gb ddr4 pre-installed memory vga/hdmi/dp/idp two gigabit ethernet rs-232/422/485 rohs compliant
Hide thumbs
Table of Contents

Advertisement

Quick Links

TANK-870AI Embedded System
MODEL:
TANK-870AI series
Embedded System with 6th Generation Intel® Core™ Processor,
8GB DDR4 Pre-installed Memory, VGA/HDMI/DP/iDP,
Two Gigabit Ethernet, RS-232/422/485,
RoHS Compliant
User Manual
Page I
Rev. 1.00 – June 12, 2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TANK-870AI SERIES and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for IEI Technology TANK-870AI SERIES

Summary of Contents for IEI Technology TANK-870AI SERIES

  • Page 1 TANK-870AI Embedded System MODEL: TANK-870AI series Embedded System with 6th Generation Intel® Core™ Processor, 8GB DDR4 Pre-installed Memory, VGA/HDMI/DP/iDP, Two Gigabit Ethernet, RS-232/422/485, RoHS Compliant User Manual Page I Rev. 1.00 – June 12, 2018...
  • Page 2 TANK-870AI Embedded System Revision Date Version Changes June 12, 2018 1.00 Initial release Page II...
  • Page 3 TANK-870AI Embedded System Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
  • Page 4 TANK-870AI Embedded System Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product. NOTE These messages inform the reader of essential but non-critical information.

  • Page 5: Table Of Contents

    TANK-870AI Embedded System Table of Contents 1 INTRODUCTION ......................1 1.1 O ........................2 VERVIEW 1.2 M ....................3 ODEL ARIATIONS 1.3 F ........................3 EATURES 1.4 T ..................4 ECHNICAL PECIFICATIONS 1.5 F ......................6 RONT ANEL 1.6 R .......................
  • Page 6 TANK-870AI Embedded System 3.6.8 Power Input, 4-pin DIN Connector ..............30 3.6.9 RJ-45 RS-232 Serial Ports ................30 3.6.10 DB-9 RS-232/422/485 Serial Port Connectors ..........31 3.6.11 USB Connectors ..................... 32 3.6.12 VGA Connector ....................33 3.7 I ............ 34 NTERNAL ERIPHERAL NTERFACE...
  • Page 7 TANK-870AI Embedded System 4.3.6 Power Connector (PWR2) ................52 4.3.7 RS-232 Serial Port Connector (COM1_2) ............52 4.3.8 RS-232 Serial Port Connectors (COM3_4) ............. 52 4.3.9 RS-232/422/485 Serial Port Connector (COM5_6) ........52 4.3.10 USB 3.0 Connectors (USB3_CN1) ..............53 4.3.11 USB 3.0 Connectors (USB3_CN2) ..............
  • Page 8 TANK-870AI Embedded System 5.3.3 iEi Feature ......................81 5.3.4 iWDD H/W Monitor ..................82 5.3.4.1 Smart Fan Mode Configuration ..............83 5.4 C ........................84 HIPSET 5.4.1 System Agent (SA) Configuration ..............85 5.4.1.1 Memory Configuration ................86 5.4.1.2 Graphics Configuration ................87 5.4.1.3 PEG Port Configuration ................
  • Page 9 Figure 1-5: HPE-2S86 (for 2A model) ..................10 Figure 1-6: TANK-870AI slot Physical Dimensions (millimeters) ..........12 Figure 3-1: Unscrew the Cover ....................21 Figure 3-2: Remove the Cover from TANK-870AI series ............21 Figure 3-3: HDD Installation ......................22 Figure 3-4: HDD Retention Screws ..................... 22 Figure 3-5: System Fan Installation ....................
  • Page 10 TANK-870AI Embedded System Figure 3-25: TPM Module Installation ..................35 Figure 3-26: Internal DisplayPort Connector Location ............. 37 Figure 3-27: iDP Module with Bracket ..................37 Figure 3-28: iDP Module Installation ................... 38 Figure 3-29: Remove Expansion Slot Bracket ................38 Figure 3-30: Power Button ......................
  • Page 11 TANK-870AI Embedded System List of Tables Table 1-1: TANK-870AI series Model Variations ................3 Table 1-2: Technical Specifications ....................6 Table 1-3: LED Indicators Description..................9 Table 1-4: Supported Signals ...................... 10 Table 1-5: Rated Voltage and Current ..................11 Table 3-1: RJ-45 Ethernet Connector LEDs ................
  • Page 12 TANK-870AI Embedded System Table 4-22: Power Connector Pinouts (PWR1) ................52 Table 4-23: RS-232 Serial Port Connector Pinouts (COM1_2) ..........52 Table 4-24: RS-232 Serial Port Connectors Pinouts (COM3_4) ..........52 Table 4-25: RS-232/422/485 Serial Port Connector Pinout (COM5_6) ........53 Table 4-26: USB 3.0 Connectors Pinouts (USB3_CN1) .............
  • Page 13 TANK-870AI Embedded System BIOS Menus BIOS Menu 1: Main ........................60 BIOS Menu 2: Advanced ......................61 BIOS Menu 3: CPU Configuration ....................62 BIOS Menu 4: Trusted Computing ....................64 BIOS Menu 5: ACPI Configuration ....................65 BIOS Menu 6: SATA Configuration ..................... 66 BIOS Menu 7: AMT Configuration ....................
  • Page 14 TANK-870AI Embedded System BIOS Menu 31: PCH Azalia Configuration Menu ............... 99 Page XIV...

  • Page 15: Introduction

    TANK-870AI Embedded System Chapter Introduction Page 1...

  • Page 16: Overview

    Intel® Q170 chipset and supports two 260-pin DDR4 SDRAM SO-DIMM modules up to 32 GB (8GB memory preinstalled). The TANK-870AI series includes one VGA port, one HDMI/DP port, one iDP port (optional), two GbE LAN ports, four USB 3.0 ports, four USB 2.0 ports, four RS-232 connectors and two RS-232/422/485 connectors.

  • Page 17: Model Variations

    TANK-870AI Embedded System 1.2 Model Variations The model variations of the TANK-870AI series are listed below. Model No. System Fan Intel® Core™ i5-6500TE 2.3GHz, (Up TANK-870AI-i5/8G/2A-R10 optional to 3.3 GHz, Quad Core, TDP 35W) Intel® Core™ i7-6700TE 2.4GHz, (up TANK-870AI-i7/8G/2A-R10 optional to 3.4 GHz, Quad Core, TDP 35W)

  • Page 18: Technical Specifications

    TANK-870AI Embedded System 1.4 Technical Specifications The TANK-870AI series technical specifications are listed in Table 1-2. Specifications Chassis Black C + Silver Color Dimensions (WxHxD) (mm) 121.5 x 255.2 x 205 System Fan Fanless Chassis Construction Extruded aluminum alloy Motherboard Intel®...
  • Page 19 TANK-870AI Embedded System Specifications 4 x RS-232 (2 x RJ-45, 2 x DB-9 w/2.5KV isolation protection) COM Port 2 x RS-232/422/485 (DB-9) Digital I/O 8-bit digital I/O, 4-bit input/4-bit output 1 x VGA Display 1 x HDMI/DP 1 x iDP (optional) VGA: Up to 1920 x 1200 @ 60Hz Resolution HDMI/DP: Up to 4096 x 2304 @ 60Hz...

  • Page 20: Front Panel

    Microsoft® Windows® 10 IoT Enterprise Linux Ubuntu 16.04 Table 1-2: Technical Specifications 1.5 Front Panel The front panel of the TANK-870AI series has the following features (Figure 1-3): Figure 1-2: TANK-870AI series Front Panel Connectors on the front panel include the following: ...

  • Page 21: Rear Panel

    TANK-870AI Embedded System 1.6 Rear Panel The rear panel of the TANK-870AI series has the following features (Figure 1-3): Figure 1-3: TANK-870AI series Rear Panel Connectors and buttons on the rear panel include the following:  1 x 4-pin power DC jack for 9 V ~ 36 V power input ...

  • Page 22: Led Indicators

     1 x AT/ATX mode switch 1.7 LED Indicators There are several indicators on the rear panel of the TANK-870AI series as shown in Figure 1-4. Figure 1-4: TANK-870AI series LED Indicators The descriptions of each LED indicator are listed below.

  • Page 23: Table 1-3: Led Indicators Description

    TANK-870AI Embedded System LED Indicator Description Shows HDD status. BLUE: CPU temperature is normal. CPU Temperature Alert RED: CPU temperature is too high. Table 1-3: LED Indicators Description WARNING: The CPU Temperature Alert LED turns red when the CPU temperature is too high.

  • Page 24: Backplane Options

    TANK-870AI Embedded System 1.8 Backplane Options The backplane options of the TANK-870AI series are shown below. Figure 1-5: HPE-2S86 (for 2A model) PWR1: Description +12 V +12 V The supported signals of the backplane slots are listed below. Backplane Slot...

  • Page 25: Table 1-5: Rated Voltage And Current

    TANK-870AI Embedded System The rated voltage and current of the backplanes are listed below. Rated Voltage Rated Current +5 V 4.0 A +12 V 2.5 A -12 V 0.1 A +3.3 V 5.0 A Table 1-5: Rated Voltage and Current WARNING: The system default power is 120 W.

  • Page 26: Physical Dimensions

    TANK-870AI Embedded System 1.9 Physical Dimensions The physical dimensions of the TANK-870AI slot are shown in Figure 1-6. Figure 1-6: TANK-870AI slot Physical Dimensions (millimeters) Page 12...

  • Page 27: Unpacking

    TANK-870AI Embedded System Chapter Unpacking Page 13...

  • Page 28: Anti-Static Precautions

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-870AI series. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the TANK-870AI series or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

  • Page 29: Unpacking Checklist

    If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the TANK-870AI series from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@ieiworld.com.
  • Page 30 TANK-870AI Embedded System Quantity Item and Part Number Image Standard HDMI Security Holder RJ-45 to DB-9 COM port cable Wi-Fi antenna Power cord (US) Power adapter, The following table lists the optional items that can be purchased separately. Optional +12V DC, 4-pin, 40 mm x 40 mm x10 mm, 6500RPM, RoHS (P/N: 19Z00-000605-00-RS) IPMI 2.0 adapter card with AST2400 BMC chip for DDR3 SO-DIMM socket interface...
  • Page 31 TANK-870AI Embedded System Optional DisplayPort to DisplayPort converter board (For iEi IDP connector) (P/N: DP-DP-R10) DisplayPort to HDMI converter board (For iEi IDP connector) (P/N: DP-HDMI-R10) DisplayPort to 24 bit dual channel LVDS converter board (For iEi IDP connector) (P/N: DP-LVDS-R10) DisplayPort to VGA converter board (For iEi IDP connector) (P/N: DP-VGA-R10)
  • Page 32 TANK-870AI Embedded System Optional OS Image with Windows Embedded Standard 10 E High End 64-bit for TANK-870-Q170-i7 Series, with DVD-ROM, RoHS (P/N: TANK-870-Q170-W10E64-H-R10) OS Image with Windows Embedded Standard 10 E Value 64-bit for TANK-870-Q170-i5 Series, with DVD-ROM, RoHS (P/N: TANK-870-Q170-W10E64-V-R10) Page 18...

  • Page 33: Installation

    TANK-870AI Embedded System Chapter Installation Page 19...

  • Page 34: Installation Precautions

    Electric shock and personal injury might occur if the rear panel of the TANK-870AI series is opened while the power cord is still connected to an electrical outlet.

  • Page 35: Figure 3-1: Unscrew The Cover

    TANK-870AI Embedded System Figure 3-1: Unscrew the Cover Step 2: Unplug the SATA signal and power cables connected to the TANK-870AI series, and then put the cover on a flat surface (Figure 3-2). Figure 3-2: Remove the Cover from TANK-870AI series...

  • Page 36: Figure 3-3: Hdd Installation

    Step 4: Secure the HDD with the HDD bracket by four retention screws (Figure 3-4). Figure 3-4: HDD Retention Screws Step 5: Reconnect the SATA signal and power cables to the TANK-870AI series. Step 6: Reinstall the cover. Page 22...

  • Page 37: System Fan Installation

    Unplug the SATA signal and power cables connected to the TANK-870AI series, and then place the cover on a flat surface (Figure 3-2). Step 3: Attach the system fan to the TANK-870AI series and secure it by four retention screws (Figure 3-5). Figure 3-5: System Fan Installation...

  • Page 38: Wi-Fi Antenna Installation

    TANK-870AI Embedded System 3.4 Wi-Fi Antenna Installation To install the Wi-Fi antennas to the TANK-870AI series series for efficient wireless network transmission, follow the steps below. Step 1: Locate the antenna connectors on the rear panel of the embedded system.

  • Page 39: External Peripheral Interface Connectors

    TANK-870AI Embedded System Left Side Panel Figure 3-7: Mounting Bracket Retention Screws Step 3: Secure the brackets to the system by inserting two retention screws into each bracket (Figure 3-7). Step 4: Drill holes in the intended installation surface. Step 5: Align the mounting holes in the sides of the mounting brackets with the predrilled holes in the mounting surface.

  • Page 40: Acc Mode Selection

    TANK-870AI Embedded System 3.6.1 ACC Mode Selection The ACC mode is designed for vehicle applications. The TANK-870AI series allows turning the ACC mode on or off. The setting can be made through the ACC mode switch on the external peripheral interface panel as shown below.

  • Page 41: At/Atx Power Mode Selection

    TANK-870AI Embedded System 3.6.2 AT/ATX Power Mode Selection The TANK-870AI series supports AT and ATX power modes. The setting can be made through the AT/ATX power mode switch on the external peripheral interface panel as shown below. Figure 3-9: AT/ATX Power Mode Switch 3.6.3 Audio Connector...

  • Page 42: Digital Input/Output Connector

    Locate the RJ-45 connectors. The locations of the RJ-45 connectors are shown in Figure 1-3. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the TANK-870AI series. See Figure 3-13. Page 28...

  • Page 43: Figure 3-13: Lan Connection

    TANK-870AI Embedded System Figure 3-13: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Figure 3-14: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked.

  • Page 44: Power Input, 3-Pin Terminal Block

    TANK-870AI Embedded System 3.6.7 Power Input, 3-pin Terminal Block The power connector connects the leads of a 9 V~36 V DC power supply into the terminal block. Make sure that the power and ground wires are attached to the correct sockets of the connector.

  • Page 45: Rs-232/422/485 Serial Port Connectors

    TANK-870AI Embedded System Figure 3-17: RJ-45 RS-232 Serial Device Connection Step 3: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the RJ-45 to DB-9 COM port cable. Step 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector.

  • Page 46: Usb Connectors

    TANK-870AI Embedded System Step 2: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the external peripheral interface. See Figure 3-19. Figure 3-19: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector.

  • Page 47: Vga Connector

    DB-15 connector on the external peripheral interface. Step 3: Insert the VGA connector. Once the connectors are properly aligned with, insert the male connector from the VGA screen into the female connector on the TANK-870AI series. See Figure 3-22. Page 33...

  • Page 48: Internal Peripheral Interface Connectors

    TANK-870AI Embedded System Figure 3-22: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Figure 3-23: VGA Connector 3.7 Internal Peripheral Interface Connectors 3.7.1 TPM Module Installation To install the TPM module, please follow the steps below:...

  • Page 49: Figure 3-24: Tpm Connector Location

    TANK-870AI Embedded System Step 2: Locate the TPM connector. The location of the TPM connector is shown in Figure 3-24. Figure 3-24: TPM Connector Location Step 3: Insert the TPM module. Make sure that pin 1 on the TPM module corresponds to pin 1 on the TPM connector (Figure 3-25).

  • Page 50: Idp Module Installation

    Through the IEI iDP converter cards, the iDP connector can support different display specifications, such as VGA, HDMI, DVI-D, LVDS and DisplayPort. To connect an iDP module to TANK-870AI series please follow the instructions below. Step 1: Loosen the two thumbscrews on the front panel, slide the cover outward, and then lift the cover up gently (Figure 3-1).

  • Page 51: Figure 3-26: Internal Displayport Connector Location

    TANK-870AI Embedded System Figure 3-26: Internal DisplayPort Connector Location Step 3: Secure the iDP module with the bracket by tightening the two retention screws on either side of the iDP module. Figure 3-27: iDP Module with Bracket Step 4: Connect the iDP module to the DisplayPort connector on the motherboard. See Figure 3-28.

  • Page 52: Figure 3-28: Idp Module Installation

    TANK-870AI Embedded System Figure 3-28: iDP Module Installation Step 5: Remove the retention screws on the expansion slot bracket. See Figure 3-29. Figure 3-29: Remove Expansion Slot Bracket Step 6: Secure the iDP module with bracket to the system. Step 7: Reinstall the cover.

  • Page 53: Table 3-3: Idp Converter Cards

    TANK-870AI Embedded System WARNING: Installing the iDP module will occupy one expansion slot. The following table lists the iDP converter cards that can be installed to the system. DisplayPort to HDMI converter board (for IEI iDP connector) (P/N: DP-HDMI-R10) DisplayPort to LVDS converter board (for IEI iDP connector) (P/N: DP-LVDS-R10) DisplayPort to VGA converter board (for IEI iDP...

  • Page 54: Powering On/Off The System

    TANK-870AI Embedded System 3.8 Powering On/Off the System WARNING: Make sure a power supply with the correct input voltage is being fed into the system. Incorrect voltages applied to the system may cause damage to the internal electronic components and may also cause injury to the user. ...

  • Page 55: Acc On Mode

    3.9.1 ACC ON Mode 1. The TANK-870AI series supports single power input and also can be simultaneously connected to two power sources. When both power connectors are connected to power sources with 9 V~36 V power input, the one with higher voltage will supply power to the system.

  • Page 56: Acc Off Mode

    10s. 3.9.2 ACC OFF Mode 1. The TANK-870AI series supports single power input and also can be simultaneously connected to two power sources. When both power connectors are connected to power sources with 9 V~36 V power input, the one with higher voltage will supply power to the system.

  • Page 57: System Motherboard

    TANK-870AI Embedded System Chapter System Motherboard Page 43...

  • Page 58: Overview

    TANK-870AI Embedded System 4.1 Overview This chapter details all the jumpers and connectors of the system motherboard. 4.1.1 Layout The figures below show all the connectors and jumpers of the system motherboard. The Pin 1 locations of the on-board connectors are also indicated in the diagram below. Figure 4-1: System Motherboard (Front) Figure 4-2: System Motherboard (Rear) Page 44...

  • Page 59: Internal Peripheral Connectors

    TANK-870AI Embedded System 4.2 Internal Peripheral Connectors The table below shows a list of the internal peripheral interface connectors on the system motherboard. Pinouts of these connectors can be found in the following sections. Connector Type Label Backplane power connector 4-pin wafer Battery connector 2-pin wafer...

  • Page 60: Battery Connector (Bat1)

    TANK-870AI Embedded System 4.2.2 Battery Connector (BAT1) PIN NO. DESCRIPTION VBATT Table 4-3: Battery Connector Pinouts (BAT1) 4.2.3 BIOS Programming Connector (JSPI1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION +V3.3M_SPI_CON SPI_CS SPI_SO_SW SPI_CLK_SW SPI_SI_SW Table 4-4: BIOS Programming Connector Pinouts (JSPI1) 4.2.4 CPU Fan Connector (CPU_FAN1) PIN NO.

  • Page 61: Ec Debug Connector (Cn4)

    TANK-870AI Embedded System DPD_OB_LANE1_N_C VCC3 Table 4-6: DisplayPort connector Pinouts (DP1) 4.2.6 EC Debug Connector (CN4) PIN NO. DESCRIPTION PIN NO. DESCRIPTION KSI0 KSO9 KSO0 KSO10 KSO1 KSO12 KSO2 KSI1 KSO3 KSO11 KSO4 KSI2 KSO5 KSI3 KSO6 KSO7 KSO8 Table 4-7: EC Debug Connector Pinouts (CN4) 4.2.7 EC Programming Connector (JSPI2) PIN NO.

  • Page 62: Led Connector (J2)

    TANK-870AI Embedded System 4.2.9 LED Connector (J2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION +V3.3S_IO +V3.3A_EC_IO IRST_PD# IATX_LED# IPWRLED01# IPWRLED02# IIPMI_LED# ICPU_LED# IDISKLED# Table 4-10: LED Connector Pinouts (J2) 4.2.10 SATA Power Connectors (CN2, CN3) PIN NO. DESCRIPTION +V5S Table 4-11: SATA Power Connectors Pinouts (CN2, CN3) 4.2.11 TPM Connector (TPM1) PIN NO.

  • Page 63: Usb 3.0 Connectors (Usb3-1)

    TANK-870AI Embedded System 4.2.12 USB 3.0 connectors (USB3-1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION VCC_USB3_56 USB3_RX5_N_C USB3_RX5_P_C USB3P1_TXDN5_C USB3P1_TXDP5_C USB2P5_DM1_L USB2P5_DP1_L USB2P6_DP2_L USB2P6_DM2_L USB3P1_TXDP6_C USB3P1_TXDN6_C USB3_RX6_P_C USB3_RX6_N_C VCC_USB3_56 Table 4-13: USB 3.0 connectors Pinouts (USB3-1) 4.3 External Interface Panel Connectors The table below shows a list of the external interface panel connectors on the system motherboard.

  • Page 64: Audio Jack (Jaudio1)

    TANK-870AI Embedded System 4.3.1 Audio Jack (JAUDIO1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION ILMIC1-CONN-L IJD_MIC ILMIC1-CONN-R ILFRONT-L IJD_FRONT ILFRONT-R Table 4-15: Audio Jack Pinouts (JAUDIO1) 4.3.2 DIO connector (DIO1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION DIN0 DOUT0 DIN1 DOUT1 DIN2 DOUT2 DIN3 DOUT3...

  • Page 65: Ethernet And Usb 2.0 Connectors (Lan2_Usb2)

    TANK-870AI Embedded System DESCRIPTION DESCRIPTION ILAN_MDI3_DN ILAN1_1000- ILAN1_100- ILAN1_LINK_ACT- ILAN1_LINK_PWR Table 4-18: LAN Pinouts (LAN1) 4.3.4 Ethernet and USB 2.0 Connectors (LAN2_USB2) DESCRIPTION DESCRIPTION USBV9L DATA9_N DATA9_P IO_GND USBV9L DATA10_N DATA10_P IO_GND Table 4-19: USB 2.0 Port Pinouts (USB2) DESCRIPTION DESCRIPTION ITRD2P0 ITRD2N0...

  • Page 66: Power Connector (Pwr2)

    TANK-870AI Embedded System 4.3.6 Power Connector (PWR2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION ACCON +VIN Table 4-22: Power Connector Pinouts (PWR1) 4.3.7 RS-232 Serial Port Connector (COM1_2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1(10) 6(15) 2(11) 7(16) 3(12) 8(17) 4(13) 9(18) 5(14) Table 4-23: RS-232 Serial Port Connector Pinouts (COM1_2)

  • Page 67: Usb 3.0 Connectors (Usb3_Cn1)

    TANK-870AI Embedded System 7(16) 8(17) 9(18) Table 4-25: RS-232/422/485 Serial Port Connector Pinout (COM5_6) 4.3.10 USB 3.0 Connectors (USB3_CN1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION VCC_USB12 USB_PN1_C USB_PP1_C USB3_RX1_N_C USB3_RX1_P_C USB3_TX1_N_C USB3_TX1_P_C VCC_USB12 USB_PN2_C USB_PP2_C USB3_RX2_N_C USB3_RX2_P_C USB3_TX2_N_C USB3_TX2_P_C Table 4-26: USB 3.0 Connectors Pinouts (USB3_CN1) 4.3.11 USB 3.0 Connectors (USB3_CN2) PIN NO.

  • Page 68: Vga Connector (Vga1)

    TANK-870AI Embedded System 4.3.12 VGA Connector (VGA1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION Green Blue VGAVCC HOTPLUG DDCDAT HSYNC VSYNC DDCCLK Table 4-28: VGA Connector Pinouts (VGA1) Page 54...

  • Page 69: Bios

    TANK-870AI Embedded System Chapter BIOS Page 55...

  • Page 70: Introduction

    TANK-870AI Embedded System 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 71: Getting Help

    TANK-870AI Embedded System Function Decrease the numeric value or make changes Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu General help, only for Status Page Setup Menu and Option...
  • Page 72 TANK-870AI Embedded System  Save & Exit – Selects exit options and loads default settings. The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. Page 58...

  • Page 73: Main

    TANK-870AI Embedded System 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Main Advanced Chipset...

  • Page 74: Advanced

    TANK-870AI Embedded System BIOS Menu 1: Main The Main menu has two user configurable fields:  System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year.  System Time [xx:xx:xx] Use the System Time option to set the system time.

  • Page 75: Cpu Configuration

    TANK-870AI Embedded System Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced > CPU Configuration Trusted Computing > Trusted Computing Settings > ACPI Settings > SATA Configuration > AMT Configuration > F81866 Super IO Configuration ---------------------- > RTC Wake Settings : Select Screen >...

  • Page 76: Bios Menu 3: Cpu Configuration

    TANK-870AI Embedded System Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced CPU Configuration When enabled, a VMM can utilize the additional Type Intel(R) Core(TM) hardware capabilities i7-6700TE CPU @ 2.40GHz provided by Vanderpool 0x506E3 Technology. Speed 2400 MHz L1 Data Cache 32 kB x 4 L1 Instruction Cache...
  • Page 77 TANK-870AI Embedded System  Intel (VMX) Virtualization Technology [Enabled] Use the Intel (VMX) Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel Virtualization technology allows several OSs to run on the same system at the same time. ...

  • Page 78: Trusted Computing

    TANK-870AI Embedded System  C State [Disabled] Use the C State option to enable or disable CPU C State.  Disables CPU C State. Disabled EFAULT  Enables CPU C State. Enabled 5.3.2 Trusted Computing Use the Trusted Computing menu (BIOS Menu 4) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM).

  • Page 79: Acpi Settings

    TANK-870AI Embedded System  Pending Operation [None] Use the Pending Operation option to schedule an operation for the security device.  No operation. None EFAULT  Clear TPM status. TPM Clear 5.3.3 ACPI Settings The ACPI Settings menu (BIOS Menu 5) configures the Advanced Configuration and Power Interface (ACPI) options.

  • Page 80: Sata Configuration

    TANK-870AI Embedded System 5.3.4 SATA Configuration Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced SATA Configuration Enable or disable SATA Device.

  • Page 81: Amt Configuration

    TANK-870AI Embedded System  Disabled Disables the hot plug function. EFAULT  Enables the hot plug function. Enabled 5.3.5 AMT Configuration The AMT Configuration menu (BIOS Menu 7) allows the advanced power management options to be configured. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced Intel AMT [Enabled]...

  • Page 82: F81866 Super Io Configuration

    TANK-870AI Embedded System  Disabled Not perform ME unconfigure EFAULT  To perform ME unconfigure Enabled 5.3.6 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the serial ports. Aptio Setup Utility –...

  • Page 83: Serial Port N Configuration

    TANK-870AI Embedded System 5.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced Serial Port n Configuration Enable or Disable Serial Port (COM) Serial Port [Enabled]...

  • Page 84: Serial Port 2 Configuration

    TANK-870AI Embedded System  IO=3F8h; IRQ=3, Serial Port I/O port address is 3F8h and the 4, 7, 9, 10, 11 interrupt address is IRQ3, 4, 7, 9, 10, 11  Serial Port I/O port address is 2F8h and the IO=2F8h; IRQ=3, interrupt address is IRQ3, 4, 7, 9, 10, 11 4, 7, 9, 10, 11 ...

  • Page 85: Serial Port 3 Configuration

    TANK-870AI Embedded System  IO=2E8h; IRQ=3, Serial Port I/O port address is 2E8h and the 4, 7, 9, 10, 11 interrupt address is IRQ3, 4, 7, 9, 10, 11 5.3.6.1.3 Serial Port 3 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. ...

  • Page 86: Serial Port 4 Configuration

    TANK-870AI Embedded System 5.3.6.1.4 Serial Port 4 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disabled Disable the serial port  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.

  • Page 87: Serial Port 6 Configuration

    TANK-870AI Embedded System  Enabled Enable the serial port EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.  The serial port IO port address and interrupt Auto EFAULT address are automatically detected.

  • Page 88: Rtc Wake Settings

    TANK-870AI Embedded System  Disabled Disable the serial port  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto The serial port IO port address and interrupt EFAULT address are automatically detected.

  • Page 89: Bios Menu 10: Rtc Wake Settings

    TANK-870AI Embedded System Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date:: hr:: min::sec specified ---------------------- : Select Screen ↑...

  • Page 90: Serial Port Console Redirection

    TANK-870AI Embedded System 5.3.8 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 11) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port. Aptio Setup Utility –...

  • Page 91: Console Redirection Settings

    TANK-870AI Embedded System  Enabled Enabled the console redirection function 5.3.8.1 Console Redirection Settings The Console Redirection Settings menu (BIOS Menu 12) allows the console redirection options to be configured. The option is active when Console Redirection option is enabled. Aptio Setup Utility –...
  • Page 92 TANK-870AI Embedded System  Bits per second [115200] Use the Bits per second option to specify the transmission speed of the serial port.  The transmission speed is 9600 9600  The transmission speed is 19200 19200  38400 The transmission speed is 38400 ...

  • Page 93: Intel Txt(Lt) Configuration

    TANK-870AI Embedded System  Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit. ...

  • Page 94: Usb Configuration

    TANK-870AI Embedded System  Enabled Enables the Intel Trusted Execution Technology. 5.3.2 USB Configuration Use the USB Configuration menu (BIOS Menu 14) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB...

  • Page 95: Iei Feature

    TANK-870AI Embedded System  Enabled Legacy USB support enabled EFAULT  Legacy USB support disabled Disabled  Auto Legacy USB support disabled if no USB devices are connected 5.3.3 iEi Feature Use the iEi Feature menu (BIOS Menu 15) to configure the iEi features. Aptio Setup Utility –...

  • Page 96: Iwdd H/W Monitor

    TANK-870AI Embedded System 5.3.4 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 16) shows the operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Advanced PC Health Status Offset from factory set Tcc activation CPU Temperature :+46 C...

  • Page 97: Smart Fan Mode Configuration

    TANK-870AI Embedded System +V5S +V12S +VDDQ MBATTERY_IN1_EC SBATTERY_A_EC  Tcc Activation Offset Use the Tcc Activation Offset option to change the Tcc Activation Offset value. If CPU Temperature reaches Tcc Activation Offset then reduces CPU Frequency.  Minimum Value: 0°C ...

  • Page 98: Chipset

    TANK-870AI Embedded System  Auto Mode The fan adjusts its speed using these EFAULT settings: CPU_FAN1 Start Temperature CPU_FAN1 Off Temperature CPU_FAN1 Start PWM  Manual Mode The fan spins at the speed set in the manual setting  CPU_FAN1 Start/Off Temperature Use the + or –...

  • Page 99: System Agent (Sa) Configuration

    TANK-870AI Embedded System Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset > System Agent (SA) Configuration System Agent (SA) > PCH-IO Configuration Parameters --------------------- : Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. General Help Previous Values Optimized Defaults Save &...

  • Page 100: Memory Configuration

    TANK-870AI Embedded System  Enabled Enable VT-d support. 5.4.1.1 Memory Configuration Use the Memory Configuration submenu (BIOS Menu 20) to view memory information. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset Memory Information Maximum Value of TOLUD. Dynamic assignment would Total Memory 8192 MB...

  • Page 101: Graphics Configuration

    TANK-870AI Embedded System  2.75 GB  3 GB  3.25 GB  3.5 GB 5.4.1.2 Graphics Configuration Use the Graphics Configuration (BIOS Menu 21) menu to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset Graphics Configuration Select which of...
  • Page 102 TANK-870AI Embedded System  Internal Graphics [Enabled] Use the Internal Graphics option to keep IGFX enabled or disabled based on the setup options.  Auto  Disabled  Enabled Default  DVMT Pre-Allocated [256M] Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots.

  • Page 103: Peg Port Configuration

    TANK-870AI Embedded System  DP (Pin Header) 5.4.1.3 PEG Port Configuration Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset PEG Port Configuration Configure PEG 0:1:0 Max Speed PEG 0 :1 :0 Not Present Max Link Speed [Auto] PEG 0 :1 :1 Not Present ----------------------...

  • Page 104: Pch-Io Configuration

    TANK-870AI Embedded System 5.4.2 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 23) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Chipset PCH-IO Configuration Select the state system should be when restoring Auto Power Button Status [Disabled(ATX)] on AC Power Loss.

  • Page 105: Pci Express Configuration

    TANK-870AI Embedded System  Enabled Power saving function is enabled. It will reduce power consumption when the system is off.  USB Power SW1 [+5V DUAL] Use the USB Power SW1 BIOS option to configure the USB power source for the corresponding USB connectors.

  • Page 106: Hd Audio Configuration

    TANK-870AI Embedded System  Disabled  Enabled Default  PCIe Speed Use PCIe Speed option to select the speed type of the PCIe Mini slot. The following options are available:  Auto Default  Gen1  Gen2  Gen3 5.4.2.2 HD Audio Configuration Use the HD Audio Configuration submenu (BIOS Menu 25) to configure the High Definition Audio codec.

  • Page 107: Security

    TANK-870AI Embedded System  HD Audio [Auto] Use the HD Audio BIOS option to enable or disable the High Definition Audio controller.  The High Definition Audio controller is disabled. Disabled  The High Definition Audio controller is enabled. Enabled ...

  • Page 108: Boot

    TANK-870AI Embedded System 5.6 Boot Use the Boot menu (BIOS Menu 27) to configure system boot options. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Boot Boot Configuration Select the keyboard Bootup NumLock State [On] NumLock state Quiet Boot [Enabled] Launch PXE OpROM [Disabled]...
  • Page 109 TANK-870AI Embedded System  Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.  Normal POST messages displayed Disabled  OEM Logo displayed instead of POST messages Enabled EFAULT  Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.

  • Page 110: Save & Exit

    TANK-870AI Embedded System  Hard Drive BBS Priorities Use the Hard Drive BBS Priorities option to set the order of the legacy devices in this group. 5.7 Save & Exit Use the Save & Exit menu (BIOS Menu 28) to load default BIOS values, optimal failsafe values and to save configuration changes.

  • Page 111: Server Mgmt

    TANK-870AI Embedded System  Restore Defaults Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this operation.  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. ...

  • Page 112: System Event Log

    TANK-870AI Embedded System 5.8.1 System Event Log Use the System Event Log menu (BIOS Menu 30) to configure the event log. Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. Server Mgmt Enabling/Disabling Options Change this to anable or SEL Components [Enabled] disable all features of...

  • Page 113: Bmc Network Configuration

    TANK-870AI Embedded System  When SEL is Full [Do Nothing] Use When SEL is FULL option to select options for reactions to a full SEL. The following options are available:  Do Nothing Default  Erase Immediately 5.8.2 BMC network configuration Use the BMC network configuration menu (BIOS Menu 31) to configure BMC network parameters.

  • Page 114: A Regulatory Compliance

    TANK-870AI Embedded System Appendix Regulatory Compliance Page 100...
  • Page 115 TANK-870AI Embedded System DECLARATION OF CONFORMITY This equipment is in conformity with the following EU directives:  EMC Directive (2004/108/EC, 2014/30/EU)  Low-Voltage Directive (2006/95/EC, 2014/35/EU)  RoHS II Directive (2011/65/EU, 2015/863/EU) If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply.
  • Page 116 TANK-870AI Embedded System Eesti [Estonian] IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 2014/53/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Español [Spanish] IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU. Ελληνική...
  • Page 117 TANK-870AI Embedded System Magyar [Hungarian] IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 2014/53/EU irányelv egyéb elõírásainak. Polski [Polish] IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU. Português [Portuguese] IEI Integration Corp declara que este equipamento está...
  • Page 118 TANK-870AI Embedded System FCC WARNING This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and   This device must accept any interference received, including interference that may cause undesired operation.

  • Page 119: Bbios Options

    TANK-870AI Embedded System Appendix BIOS Options Page 105...
  • Page 120 TANK-870AI Embedded System Below is a list of BIOS configuration options in the BIOS chapter.  System Date [xx/xx/xx] ......................60  System Time [xx:xx:xx] ....................... 60  Intel (VMX) Virtualization Technology [Enabled] .............. 63  Active Processor Cores [All] ....................63 ...
  • Page 121 TANK-870AI Embedded System  Data Bits [8] .......................... 78  Parity [None] ......................... 78  Stop Bits [1] .......................... 79  Intel TXT(LT) Support [Disabled] ..................79  USB Devices ......................... 80  Legacy USB Support [Enabled] ..................80  Auto Recovery Function [Disabled] ...................
  • Page 122 TANK-870AI Embedded System  Hard Drive BBS Priorities ....................96  Save Changes and Reset ....................96  Discard Changes and Reset ....................96  Restore Defaults ........................97  Save as User Defaults ......................97  Restore User Defaults ......................97 ...

  • Page 123: C Terminology

    TANK-870AI Embedded System Appendix Terminology Page 109...
  • Page 124 TANK-870AI Embedded System AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
  • Page 125 TANK-870AI Embedded System Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
  • Page 126 TANK-870AI Embedded System Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.

  • Page 127: D Safety Precautions

    TANK-870AI Embedded System Appendix Safety Precautions Page 113...

  • Page 128: Safety Precautions

    WARNING: The precautions outlined in this appendix should be strictly followed. Failure to follow these precautions may result in permanent damage to the TANK-870AI series. Please follow the safety precautions outlined in the sections that follow: D.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times.
  • Page 129 Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-870AI series. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the TANK-870AI series is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to.

  • Page 130: Maintenance And Cleaning Precautions

    The mark on electrical and electronic products only applies to the current European Union Member States. Please follow the national guidelines for electrical and electronic product disposal. D.2 Maintenance and Cleaning Precautions When maintaining or cleaning the TANK-870AI series, please follow the guidelines below. Page 116...
  • Page 131 Some components in the TANK-870AI series may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the TANK-870AI series. ...

  • Page 132: E Digital I/O Interface

    TANK-870AI Embedded System Appendix Digital I/O Interface Page 118...

  • Page 133: Introduction

    TANK-870AI Embedded System E.1 Introduction The DIO connector on the TANK-870AI series is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.

  • Page 134: Assembly Language Sample 1

    TANK-870AI Embedded System E.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value E.3 Assembly Language Sample 2 AX, 6F09H ;setting the digital port as output BL, 09H...

  • Page 135: F Hazardous Materials Disclosure

    TANK-870AI Embedded System Appendix Hazardous Materials Disclosure Page 121...
  • Page 136 TANK-870AI Embedded System The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 137 TANK-870AI Embedded System 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代) 标准规定的限量要求以下。...

Table of Contents