Page 1
Information furnished by DAQ system is believed to be accurate and reliable. However, no responsibility is assumed by DAQ system for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or copyrights of DAQ system.
Module IO Decoder PCI-DIO6402 DOut 64bit Output [Figure 1-1. PCI-DIO64xx Internal Block Diagram] The PCI-DIO6402 is designed for high performance digital logger with PCI Interface. It has a Isolated 64 Digital Output port for external interface like Figure 1-1. http://www.daqsystem.com...
PCI-DIO6402 Users Manual (Rev 1.0) 2. Connector Pin Map The PCI-DIO6402 board is equipped with 37 pin D-SUB connector for external digital output in standard PCI Bracket. Figure 2-1 shows the bracket and connector of the board. [Figure 2-1. PCI-DIO6402 Bracket & Board Layout] [Figure 2-2.
PCI-DIO6402 Users Manual (Rev 1.0) 3. Digital Output Circuit OUT_POWER OUT_VDD +3.3V out0 DOUT0 out1 DOUT1 out63 DOUT63 [Figure 3-1. Digital Output Circuit] Figure 3-1 shows that the digital output is isolated by photo-coupler. The “OUT_POWER” is connected commonness to an output circuit. The “OUT_VDD” works external power or 5V PCI of internal board or ISO 5V (DC-DC Output power) according to connector J2 jumper setting.
PCI-DIO6402 Users Manual (Rev 1.0) 4. External Connection (OUTPUT) PCI-DIO6402 Board J2 Jumper Setup External DC-DC Connection Power OUT_POWER PCI Power JP1 Jumper Setup OUT_VDD Load +3.3V DOUT 31 - 0 POWER OUT31-0 External GROUND GROUND [Figure 4-1. Output Port External Connection] The OUTPUT can use to select the external power or internal power.
Page 10
PCI-DIO6402 Users Manual (Rev 1.0) OUT_POWER OUT_VDD POWER OUT 31-0 GROUND [Figure 4-2. External Connection] Figure 4-2 shows the making an output port connection as it uses a 37pin D-Sub connector. http://www.daqsystem.com...
PCI-DIO6402 Users Manual (Rev 1.0) 5. Board Option Setup DC-CD POWER Converter J2 JP1 (선택사양) GROUND [Figure 5-1. cPCI-DIO6402 Appearance] 5-1. Power Option Setup If usable environment don’t use external power, it can use at boards which it supplied the power.
Page 12
PCI-DIO6402 Users Manual (Rev 1.0) 5.1.1 J2 Jumper Setup J2 Jumper Setup POWER PIN Floating(External Power Use) DC-DC converter Power PC +5V Output * Refer Figure 5-1 5.1.2 JP1 Jumper Setup JP1 Jumper Setup PC GROUND * Refer Figure 5-1 * The basic option doesn’t work to set up a jumper setting in case of shipment.
Page 13
PCI-DIO6402 Users Manual (Rev 1.0) 5-2. Board Address Setup Several DIO6402 series boards classify each board address, you shall use it at systems that a lot of I/O ports was required. Distribution of each board sets it up through 4 pin switch (SW1) in a board. A system is designed of 4 maximum boards at the same time so as usable.
PCI-DIO6402 Users Manual (Rev 1.0) 6. Installation The installation order is as follows, explain Windows XP basis if there isn’t special explanation. (1) If new hardware is found, Wizard will ask you to install the corresponding driver. For installation of the driver, select the item “Install from a list or specific location (Advanced)” and click “Next”...
Page 15
PCI-DIO6402 Users Manual (Rev 1.0) (3) When you click Next, the driver files are installed. (4) When the installation is complete, normally same as the picture below. http://www.daqsystem.com...
Page 16
PCI-DIO6402 Users Manual (Rev 1.0) (5) If the installation is completely finished, you confirm it in the following ways. Do the following steps to show up the “Device Manager” window. [My Computer -> properties -> Hardware -> Device Manager -> Multifunction Adaptors -> PCI-DIO6400] [Figure 6-2.
Page 17
If you can see the “PCI-DIO6400” at Multifunction Adaptors, the driver installation is to have been over. (Check the red circle) The PCI-6402 driver is the same as the PCI-DIO6402. Notice : After installation, you should re-boot the system for the proper operation.
7. Sample Program Explanation 7-1 Program Interface DAQ system provides a sample program to make the user be familiar with the board operation and to make the program development easier. You can find the sample program in the CDROM accompanying with the board. One of the execution file is “PCI_DIO6400.exe”.
Page 19
PCI-DIO6402 Users Manual (Rev 1.0) 7-2 Function Explanation Name Description Note Model No Select the Model Name PCI-DIO6400 selection Board No Select the Board Number (Board#0 ~ #3) By SW1 Setup Open Device Open the selected Board List Device It displays a board number which installed in a Not Used currently.
Page 20
PCI-DIO6402 Users Manual (Rev 1.0) References 1. PCI System Architecture -- MindShare Inc. 2. PCI Local Bus Specification -- PCI-SIG 3. General information on PCI board API -- DAQ system 4. AN201 How to build application using APIs -- DAQ system 5.