Page 1
C O M B I V E R T GB Installation manual Encoder interfaces COMBIVERT with safety function STO F5-K/ -L/ -P Original manual Mat.No. Rev. DXF5ZEM-K001...
Contents Table of contents Preface ......................5 Information on special measures ..................5 Documentation ........................5 Validity and liability ......................5 Copyright ..........................6 1.5 Specified application ......................6 Product description ......................7 Safety Instructions ..................8 Preparatory measures ......................9 Secure customer parameterization ..................9 Mechanical installation ................10 Housing D and E ........................10 3.1.1 Demounting the device ......................10...
Page 4
Contents List of figures Figure 1: Demounting of the device housing D and E ............10 Figure 2: Installation of the encoder interface housing D and E ..........11 Figure 3: Demounting the device housing G and H ...............12 Figure 4: Installation of the interface board housing G and H ..........13 Figure 5: Installation of the interface board housing R ............14 GB - 4...
Precondition for all further steps is the knowledge and observance of the safety and operating instructions (Instruction manual Part 1). This is provided accompanied by the device or by the download site of www.keb.de. Non-observance of the safety and operating instructions leads to the loss of any liability claims.
The used semiconductors and components of Karl E. Brinkmann GmbH are developed and di- mensioned for the use in industrial products. If the KEB COMBIVERT F5 is used in machines, which work under exceptional conditions or if essential functions, life-supporting measures or an extraordinary safety step must be fulfilled, the necessary reliability and security must be ensured by the machine builder.
The functionality of the drive/servo can change by installation, alteration or replacement of encoder interfaces. The functionality is dependent on the setting/programming by the ma- chine manufacturer. COMBIVERT F5 with safety function is marked in the material number in the fifth position with the letters K, L or P: •...
In the range of safety technology, authorized personnel must be confirmed in written document by KEB. Warning Note capacitor discharge time Before any installation and connecting work, the unit must be disconnected from mains and secure it accordingly.
Safety Instructions Warning Do not open any electrical connections No internal electrical connections may be opened during installation or changing of the encoder interface. The certification for "functional safety" expires in case of contravention. The opening of electrical connections with the following required tests is only permissible of authorized personnel by Karl E.
Mechanical installation Mechanical installation Housing D and E The mechanical installation is dependent on the housing. The housing can be identified through the 7th digit of the material number: • xxF5xxD-xxxx => housing D • xxF5xxE-xxxx => housing E 3.1.1 Demounting the device 1 fixing bolt 2 Cover plate...
Mechanical installation 3.1.2 Installation of the interface board 1 Guide rail 2 Socket connector 3 Latch 4 Interface board 5 fixing bolt 6 Cover Figure 2: Installation of the encoder interface housing D and E Installation of the interface board •...
Mechanical installation Housing G and H The mechanical installation is dependent on the housing. The housing can be identified through the 7th digit of the material number: • xxF5xxG-xxxx => housing G • xxF5xxH-xxxx => housing H 3.2.1 Demounting the device 1 Cut-outs for cover fixing 4 Operator 2 Screws M2.5 x 6...
Mechanical installation 3.2.2 Installation of the interface board 1 Cut-outs for cover fixing 4 Cover 2 Screws M2.5 x 6 5 Operator 3 Interface board 6 Cut-outs for cover fixing Figure 4: Installation of the interface board housing G and H Installation of the interface board •...
Mechanical installation Housing larger H The mechanical installation is dependent on the housing. The housing can be identified through the 7th digit of the material number: • xxF5xxP-xxxx => housing P • xxF5xxR-xxxx => housing R • xxF5xxU-xxxx => housing U •...
Page 15
Mechanical installation Preparing for Installation • Pull cover fixings (5) upwards and remove cover (6) • Solve operator (4) by pressing on the latch and pull upwards • Solve screws (7) and remove carrier plate (3) • Unscrew screws (2) from the distance pins (included distance pins are not required for devices with functional safety.
Serial number of the inverter Status of the material number: Material number as shown above is released Material number check / awarded by KEB Material number of the en- coder interface New type plate required ? Consignment with costs by KEB? The service employee confirms with his signature that all work has been carried out carefully and completely in accordance with this instruction.