6: Operating The Device; 7: Scene Id - FIBARO SWIPE FGGC-001 Operating Manual

10

#6: Operating the device

Acoustic and visual indications:
i
NOTE
The Swipe is equipped with a buzzer and LED diode, signalling ges-
Gestures are not in-
ture detection, menu position and status of the device.
dicated by the LED
diode by default. In
validity of every detected gesture or sequence is signalled by:
order to enable it, set
• 2 short beeps (GREEn) - gesture/sequence is valid
the value of parame-
ter 3 to 1.
• Intermittent tone (GREEn) - smooth control using circular
gesture
• 1 long beep (RED) - gesture/sequence is invalid
Menu allows to perform Z-Wave network actions. In order to use the
i
NOTE
menu:
If the device is battery
1. Move and hold your hand close to the center of the pad.
powered, high pitch
beep will signalize ex- 2. Loud sound sequence will confirm entering the menu, keep
iting from the Standby
holding your hand.
Mode before entering
3. Wait for the buzzer to indicate the desired menu position:
the menu.
• 1 short beep (WhITE indicator colour) - wake up the device
i
NOTE
• 2 short beeps (GREEn indicator colour) - learning mode
Menu can also be (adding/removing)
operated using the
• 3 short beeps (YELLOW indicator colour) - the device reset
service button B (see
"Additional features"
4. To select current position, withdraw the hand and perform swiping
on page 15).
up gesture to confirm selection (two beeps will confirm validity).
Waking up the device:
The Swipe needs to be woken up to receive information about the
new configuration from the Z-Wave controller, like parameters and
associations. use 1st menu position to wake up the device or click the
i
NOTE
button on the back of the device once.
Resetting the device is
not the recommend-
Reset procedure of the Swipe:
ed way of removing
the device from the
Reset procedure allows to restore the device back to its factory set-
Z-Wave network. use
tings, which means all information about the Z-Wave controller and
the reset procedure
user configuration will be deleted. In order to reset the device:
only if the primary
1. Make sure the device is powered.
controller is missing
or inoperable. Certain
2. Choose 3rd menu position (3 short beeps).
device removal can be
achieved by the pro- 3. After few seconds the device will be restarted. not being added
cedure of removing
to the Z-Wave network will be signalized with sequence of 2 short
described in "Adding
beeps, pause, 1 short beep (RED).
the device" on page
8.
OPERATInG ThE DEvICE

#7: Scene ID

Scene ID:
Every basic gesture and sequence has its own Scene ID that is send
to the main controller after recognizing it. Scene activation for basic
gestures is send after second gesture or timeout.
Scene Gesture or se-
Attribute
ID quence
/\ Key Pressed 1 time
1
/\ /\ Key Pressed 2 times
\/ Key Pressed 1 time
2
\/ \/ Key Pressed 2 times
< Key Pressed 1 time
3
< < Key Pressed 2 times
> Key Pressed 1 time
4
> > Key Pressed 2 times
Key held Down
Circular gesture
5
(clockwise)
Key Released
Key held Down
Circular gesture
6
(counter-clockwise)
Key Released
7 1st sequence Key Pressed 1 time
8 2nd sequence Key Pressed 1 time
9 3rd sequence Key Pressed 1 time
10 4th sequence Key Pressed 1 time
11 5th sequence Key Pressed 1 time
12 6th sequence Key Pressed 1 time
11
i
NOTE
Toggle Mode (param-
eter 12) disallows dou-
bled gestures.
Default action
On
OFF
On
OFF
On
OFF
On
OFF
Change state
uP
STOP
Change state
DOWn
STOP
user-defined
user-defined
user-defined
user-defined
user-defined
user-defined
SCEnE ID