Related Manuals for FIBARO FGPB-101-5
Summary of Contents for FIBARO FGPB-101-5
-
Page 1: Table Of Contents
O P E R A T I N G M A N U A L FIBARO BUTTON FGPB-101 CONTENTS v1.1 #1: Description and features #5: Associations #2: Basic activation #6: Advanced parameters #3: Adding/removing the device #7: Specifications #4: Operating the device... - Page 3 General information about the FIBARO System FIBARO is a wireless smart home automation system, based on the Z-Wave protocol. All of available devices can be controlled through a computer (PC or Mac), smartphone or tablet. Z-Wave devices are not only receivers, but can also repeat the signal, increasing the Z-Wave network’s range.
-
Page 4: 1: Description And Features
FIBARO Button is a compact, battery-powered, Z-Wave Plus compatible device. It allows you to control devices through the Z-Wave network and run various scenes defined in FIBARO System. Different actions may be triggered with one to five clicks or by holding the button down. -
Page 5: 2: Basic Activation
#2: Basic activation 1. Press and turn the button counter-clockwise to open the casing. 2. Remove the paper strip underneath the battery. 3. Press and turn the button clockwise to close the casing. 4. Place the device within the direct range of your Z-Wave controller. 5. -
Page 6: 3: Adding/Removing The Device
#3: Adding/removing the device Adding (Inclusion) - Z-Wave device learning mode, allowing to add NOTE the device to existing Z-Wave network. Adding Security To add the device to the Z-Wave network: Mode must be per- formed up to 2 meters 1. -
Page 7: 4: Operating The Device
#4: Operating the device Operating the Button: 1 click: send action to associated devices (switch on/off by de- fault) and/or trigger a scene 2 clicks: send action to associated devices (switch on maximum level by default) and/or trigger a scene 3 clicks: send action to associated devices (no action by default) and/or trigger a scene... -
Page 8: 5: Associations
GET commands and will not respond with a Basic Report. FIBARO Button in 2nd, 3rd and 4th group allows to control 5 regular or multichannel devices per an association group, with the exception NOTE of “LifeLine” that is reserved solely for the controller and hence only 1... -
Page 9: 6: Advanced Parameters
#6: Advanced parameters The Button allows to customize its operation to user’s needs. The set- tings are available in the FIBARO interface as simple options that may be chosen by selecting the appropriate box. In order to configure the Button (using the hC controller): 1. - Page 10 3. Associations in Z-Wave network Security Mode NOTE This parameter defines how commands are sent in specified associa- values of parameter tion groups: as secure or non-secure. Parameter is active only in Z-Wave 3 may be combined, network Security Mode. It does not apply to 1st „Lifeline” group. e.g.
- Page 11 14. Key Pressed 3 times – command sent to 2nd association group This parameter defines commands sent to devices associated in 2nd association group after a triple click. Available settings: 0 - no action 1 - SWITCh On 2 - SWITCh OFF 3 - SWITCh On/OFF –...
- Page 12 23. Key Pressed 2 times – value of SWITCH ON command sent to 3rd association group This parameter defines value of SWITCh On command sent to devices in 3rd association group after a double click. Available settings: 1-255 - sent value 2 [bytes] Default setting: Parameter size:...
-
Page 13: 7: Specifications
#7: Specifications Battery type: ER14250 ½AA 3.6v CAUTION using batteries other Battery life: est. 2 years (with default settings and than specified may max. 10 pushes per day) result in explosion. Dispose of properly, Operating temperature: 0 - 40°C (32 - 104°F) observing environ- mental... -
Page 14: 8: Regulations
All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to no- tify any individual or entity. - Page 15 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用 者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現 有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性 電機設備之干擾。 Declaration of conformity hereby, Fibar Group S.A. declares that FIBARO Button is in compliance with the essential requirements and other relevant provisions of Di- rective 1999/5/EC. REGuLATIOnS...