FIBARO SWIPE FGGC-001 Operating Manual

FIBARO SWIPE FGGC-001 Operating Manual

Swipe gesture controller
Hide thumbs Also See for SWIPE FGGC-001:

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SWIPE FGGC-001 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for FIBARO SWIPE FGGC-001

  • Page 1: Table Of Contents

    O P E R A T I N G M A N U A L FIB AR O FIBARO SWIPE FGGC-001 CONTENTS v1.0 #1: Description and features #8: Sequences of gestures #2: Gestures overview #9: Powering modes #3: Basic activation...
  • Page 2 General information about the FIBARO System FIBARO is a wireless smart home automation system, based on the Z-Wave protocol. All of available devices can be controlled through a computer (PC or Mac), smartphone or tablet. Z-Wave devices (non- battery powered) are not only receivers, but can also repeat the signal, increasing the Z-Wave network’s range.
  • Page 3: 1: Description And Features

    #1: Description and features #2: Gestures overview FIBARO Swipe is a revolutionary battery gesture control pad that Basic gestures are used to turn On and OFF associated devices or allows you to control devices in your Z-Wave network without actually trigger scenes.
  • Page 4: 3: Basic Activation

    #3: Basic activation 9. Plug the power source into the micro-uSB port if required. 1. Remove the front magnetic cover. 10. Set the main controller in (security/non-security) add mode (see the controller’s manual). 11. Move and hold your hand close to the center of the pad. 2.
  • Page 5: 4: Adding The Device

    #4: Adding the device #5: Removing the device Adding (Inclusion) - Z-Wave device learning mode, allowing to add Removing (Exclusion) - Z-Wave device learning mode, allowing to NOTE NOTE the device to existing Z-Wave network. remove the device from existing Z-Wave network. Adding security Removing the Swipe...
  • Page 6: 6: Operating The Device

    #6: Operating the device #7: Scene ID Acoustic and visual indications: Scene ID: NOTE NOTE The Swipe is equipped with a buzzer and LED diode, signalling ges- Every basic gesture and sequence has its own Scene ID that is send Gestures are not in- Toggle Mode (param- ture detection, menu position and status of the device.
  • Page 7: 8: Sequences Of Gestures

    #8: Sequences of gestures Creating and configuring sequences in the Home Center interface: 1. Go to the device options by clicking the icon on its bar: 2. Drag and drop two or three gestures to create a desired sequence. 3. Confirm the selection by clicking “Confirm a new sequence”. Sequences: 4.
  • Page 8: 9: Powering Modes

    #9: Powering modes #10: Additional features There are two powering modes of the Swipe. By default, powering Service button B: CAUTION mode of the device is updated automatically (in intervals specified in The Swipe is equipped with a service B-button, which allows to use using batteries other parameter 5) after changing type of supply.
  • Page 9: 11: Associations

    The Swipe allows to customize its operation to user’s needs. The set- participation of the the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter tings are available in the FIBARO interface as simple options that may main controller and or scene (may be controlled only through a Z-Wave controller).
  • Page 10 3. LED diode - visual indicator settings 10. Scenes sent to the controller NOTE visual indication of gestures detection. Defines which actions result in sending scenes to 1st “Lifeline” group. Parameter 10 values may be combined, Available settings: 0 - gestures detection is not indicated Available settings: 1 - scenes for flick uP gesture enabled e.g.
  • Page 11 13. Rate of smooth level control 25. SWITCH OFF control frame value for FLICK LEFT gesture Parameter allows to choose how long the hand has to be held near the This parameter allows to set value sent in SWITCh OFF command center of the pad after "AirWheel"...
  • Page 12: 13: Specifications

    #13: Specifications 33. 3rd gestures sequence (SLOT 3) value containing sequence of gestures. See "Sequences of gestures" on page 12 for more information. Available settings: 0-1076 2 [bytes] Default setting: Parameter size: Power supply: 5v DC power supply and/or batteries CAUTION 34.
  • Page 13: 14: Regulations

    All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or upda- te its products, software, or documentation without any obligation to notify any individual or entity.

Table of Contents