Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Coemar Par Lite LED White
Summary of Contents for Coemar Par Lite LED White
- Page 2 Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro Par Lite Led White: ci permetteranno di assistervi con la massima rapidità e precisione. Please note in the space provided above the relative service information of the model and the retailer from whom you purchased your Par Lite Led White : this information will assist us in providing spare parts, repairs or in answering any technical enquiries with the utmost speed and accuracy.
-
Page 3: Table Of Contents
English Index 1. Packaging and transportation Pag. 4 1.1. Packaging “ 1.2. Transportation “ 2. General information Pag. 4 2.1. Important safety information “ 2.2. Warranty conditions “ 2.3. CE Certification “ 3. Product specifications Pag. 5 3.1. Technical characteristics “... -
Page 4: Packaging
2. For mains connection, adhere strictly to the guidelines outlined in this manual. 3. The level of technology inherent in the Par Lite Led White requires the use of specialised personnel for all service applications; refer all work to your authorised Coemar service centre. -
Page 5: Technical Characteristics
212mm 7.24” 8.35” 268mm 10.5” 3.3. Projector components The principal components of the Par Lite Led White are shown in the diagram below. Components description 1. IP20 rear panel 2. IP66 rear panel 3. Projector body 4. Dip-switch panel 5. Led control PCB 6. -
Page 6: Mechanical Installation
Par Lite Led White may be floor mounted or hung from an appropriate structure in any position. Permanent installation Use the three holes “A” (Ø13) on the yoke of the Par Lite Led White for robust, permanent installation. Mobile installations If hanging the fixture from a lighting truss or similar, we recommend the use of appropriate clamps “B”, affixed to the yoke in the holes... -
Page 7: Adjusting Beam Direction
4.2. Safety chain When hanging the Par Lite Led White we recommend the use of a safety chain “C” affixed to the yoke and to the suspension device. The safety chain should be either a metal wire rope or a metal chain, both suitably rated for the purpose. -
Page 8: Opening And Closing Up The Projector
4.5. Adjusting the beam angle Several optional optical groups are available for Par Lite Led White. They are used to vary the beam dimension and make it suitable for different lighting applications and specifically: a group of lenses for a larger projection angle, a flood reflector and se veral filters that can be fitted either internally or externally to the unit The standard optical group, fitted on Par Lite Led White, is composed by a group of lenses that gives 12°... - Page 9 To vary the wideness of the beam without opening the unit, it’ s possible to install an external filter holder “S” (code CO9169/1), as shown on following drawing. The following table details the range of beam angle and diffusion filters available for the Par Lite Led White. Optical group...
-
Page 10: Operating Voltage And Frequency
• Prior to connecting the device to mains power, ensure that the mains characteristics are within the recommended range for use with the Par Lite Led White. • A good earth connection is essential for the correcdt operation of the Par Lite Led White. Never install the unit unless the yellow/gree earth cable is securely connected. -
Page 11: Connecting Dmx Signal
Control signal is digital and is transmitted via two pair screened cable, as recommended in international standards for the transmission of DMX512. Connection is serial, utilising the XLR3 sockets located on the rear panel of the Par Lite Led White. -
Page 12: Dmx Addressing
1. Setting a dip-switch to the ON position activates its function 2. The DMX address may be altered without the need to turn the Par Lite Led White off. 3. To set the 3 channels mode set the dip-switch 3Ch to the on position. - Page 13 English 7. Test function With the dip-switch set to the ON position, Par Lite Led White will test each individual channel without the need for a DMX controller to be connected. For example: set the dip-switch to ON on the Par Lite Led White.
-
Page 14: Master/Slave Mode
9.1. MASTER/SLAVE mode In MASTER/SLAVE mode, it is possible to control, via a projector set as MASTER, a series of Par Lite Led White units set to act as SLAVE fixtures. The table below displays the settings required for fixtures to be connected in this manner. -
Page 15: Stand Alone Mode
ALONE running program 1 8 16 32 64 128 To configure the Par Lite Led White as STAND ALONEsimply set dip-switch Auto to the ON position and select the program you wish to run and the hold and crossfade times to... -
Page 16: Fuse Replacement
11. Thermal protection A thermal sensor in the body of the Par Lite Led White protects the fixture against overheating. The sensor operates by removing power to the leds should the operating temperature exceed the factory preset. 12. Maintenance Whilst every possible precaution has been taken to ensure the trouble-free operation of your Par Lite Led White , the following peri- odic maintenance is highly recommended. -
Page 17: Periodic Maintenance
13. Spare parts All the components of the Par Lite Led White are available as spare parts from your Coemar service centre . Accurate description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effective manner. - Page 18 Coemar Lighting Srl via Carpenedolo, 90 - 46043 Castiglione delle Stiviere (Mantova) Italy ph. +39 03761514412 - fax +39 03761514380 info@coemar.com Coemar si riserva il diritto di apportare modifiche senza preavviso. Coemar reserves the right to effect modifications without notification...
Need help?
Do you have a question about the Par Lite LED White and is the answer not in the manual?
Questions and answers