O P E R A T I N G M A N U A L FIBARO DOOR/WINDOW SENSOR FGK-10x CONTENTS v2.0 #1: Description and features #7: Operating the device #2: Basic activation #8: Association #3: Adding/removing the device #9: Advanced parameters...
General information about the FIBARO System FIBARO is a wireless smart home automation system, based on the Z-Wave protocol. All of available devices can be controlled through a computer (PC or Mac), smartphone or tablet. Z-Wave devices are not only receivers, but can also repeat the signal, increasing the Z-Wave network’s range.
#1: Description and features FIBARO Door/Window Sensor is a wireless, battery powered reed sensor compatible with the Z-Wave standard. Changing the device’s status will automatically send signal to the Z-Wave controller and associated devices. Sensor can be used to trigger scenes and everywhere there is a need for information about opening or closing of doors, windows, garage doors, etc.
#2: Basic activation 1. Open the cover. NOTE The antenna should be placed above the battery. never cut, shorten or bend the antenna. Its length is suited to the band at which the system op- erates. 2. Remove the battery blocker. NOTE Metal surfaces in close vicinity...
#3: Adding/removing the device Adding (Inclusion) - Z-Wave device learning mode, allowing to add NOTE the device to existing Z-Wave network. Adding security To add the device to the Z-Wave network: mode must be per- 1. Close the cover. formed up to 2 meters from the controller.
#4: Temperature sensor The DS18B20 temperature sensor may be installed anywhere where CAUTION temperature readouts are necessary. If adequately protected, the DS18B20 sensor may be installed in humid conditions, under water, Connected the device in accordance with sealed in concrete or placed under the floor. the wiring diagram.
#5: Button or external sensor Door/Window Sensor is equipped with a potential-free input. It allows NOTE to change device state using the external button or sensor through Potential-free input is GnD signal. a type of input contact If the Door/Window Sensor will be used only as a binary sensor, do which does not have not install the magnet.
#6: Physical installation To install the Door/Window Sensor: 1. Stick the included self-adhesive pads to the bottom of the device and magnet. 2. Peel off the protective layer of the sticker. 3. Stick the device onto the door/window frame. 4. Stick the magnet onto the moving part of the door/window, no further than 5mm from the sensor.
Controlling the Door/Window Sensor with FIBARO Home Center controller: After adding the Sensor to the FIBARO System, it will be represented by one or two icons in home Center interface. Sensor without connected DS18B20 sensor or used with a button connected to In input (without magnet), will be represented by a sin- gle icon.
Page 11
(on default settings). plosion if the battery is replaced with an In FIBARO home Center controller current battery level is displayed incorrect type. Batter- in the interface. If a battery icon turns red, it means the battery needs ies should be recycled replacement.
#8: Association Association (linking devices) - direct control of other devices within NOTE the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter Association allows di- or scene (may be controlled only through a Z-Wave controller). rect transfer of control commands between devices, is performed The Door/Window provides the association of five groups:...
#9: Advanced parameters The Door/Window Sensor allows to customize its operation to user’s needs. Settings are available in the FIBARO interface as simple op- tions that may be chosen by selecting the appropriate box. In order to configure the Door/Window Sensor (using the home Center controller): 1.
Page 14
3. Visual LED indications NOTE This parameter defines events indicated by the visual LED indicator. Values of parameter Disabling events might extend battery life. 3 may be combined, e.g. 1+2=3 means Available settings: 0 - no indications opening/closing and 1 - indication of opening/closing status change wake up will be indi- (input In) cated by the visual in-...
Page 15
13. Value of OFF command frame sent to 2nd association group The value of 0 turns OFF the device, 255 turns it On. In case of asso- ciating the Dimmer or Roller Shutter module, values 1-99 allow to set an associated device to a specified level. Available settings: 0-99 or 255 Default setting: Parameter size:...
Page 16
50. Interval of temperature measurements This parameter defines how often the temperature will be measured. The shorter the time, the more frequently the temperature will be measured, but the battery life will shorten. Available settings: 0 - temperature measurements disabled 5-32400 - time in seconds Default setting: 300 (5min)
Page 17
56. Low temperature alarm threshold If temperature is lower than the set value, underheat notification will be sent and low temperature scene will be triggered (if activated). Available settings: -300-700 (-30-70°C, 0.1°C step) 40 (4°) 2 [bytes] Default setting: Parameter size: 70.
Page 18
72. Associations in Z-Wave network Security Mode NOTE This parameter defines how commands are sent in specified associa- Operating in Z-Wave tion groups: as secure or non-secure. Parameter is active only in Z-Wave network security network security mode. It does not apply to 1st group “Lifeline”. mode automatical- ly disables sending...
#10: Specifications Power supply: 3.6V DC battery CAUTION using batteries other Battery type: ER14250 ½ AA than specified may result in explosion. Inputs: single, potential-free (In) Dispose of properly, observing environ- Eu directives compliance: RohS 2011/65/Eu mental protection R&TTE 1999/5/EC rules.
All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or upda- te its products, software, or documentation without any obligation to notify any individual or entity.
Page 21
第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用 者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現 有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性 電機設備之干擾。 Declaration of conformity hereby, Fibar Group S.A. declares that FIBARO Door/Window Sensor is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. REGuLATIOnS...
Need help?
Do you have a question about the FGK-10x and is the answer not in the manual?
Questions and answers