FIBARO FGBHDW-002 Operating Manual
  1. Manuals
  2. Brands
  3. FIBARO Manuals
  4. Accessories
  5. FGBHDW-002
  6. Operating manual

FIBARO FGBHDW-002 Operating Manual

Fibaro door/window sensor
Hide thumbs Also See for FGBHDW-002:
Table of Contents

Advertisement

Quick Links

Download this manual
FIBARO DOOR/WINDOW SENSOR
CONTENTS
O P E R A T I N G
M A N U A L
FGBHDW-002
3
4
5
6
7
EN
v1.1
8
9
10
11

Advertisement

Table of Contents
loading

Related Manuals for FIBARO FGBHDW-002

Summary of Contents for FIBARO FGBHDW-002

  • Page 1: Table Of Contents

    O P E R A T I N G M A N U A L FIBARO DOOR/WINDOW SENSOR FGBHDW-002 CONTENTS v1.1 #1: Description and features #6: Functionalities #2: Powering the accessory #7: Configurable parameters #3: Pairing the accessory #8: Specifications...

  • Page 2: Important Safety Information

    HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod touch. After installing your FIBARO Door/Window Sensor, configure it from a compatible app with just a few simple steps. You can even create your own custom scenes to control your home settings.

  • Page 3: 1: Description And Features

    #1: Description and features FIBARO Door/Window Sensor is a HomeKit-enabled Hall effect sensor using Bluetooth® low energy technology. Along with detecting opening/closing, the accessory measures the ambient temperature. Opening is detected by separating the sensor’s body and the magnet. Tampering is detected whenever the accessory is detached from the surface or casing is opened.

  • Page 4: 2: Powering The Accessory

    #2: Powering the accessory 1. Open the cover. 2. Remove the battery blocker. 3. The accessory will glow blue for 1.5 seconds – it is ready to be paired. NOTE 4. Close the cover paying attention to the correct orientation of the if after powering ac- cover and sensor’s body.

  • Page 5: 3: Pairing The Accessory

    #3: Pairing the accessory 1. Open the Settings app on your iOS device. 2. Go to the Bluetooth® section and turn the Bluetooth® on. 3. Place the accessory next to your iOS device. 4. Open a HomeKit compatible app of your choosing on your iOS device.

  • Page 6: 4: Physical Installation

    #4: Physical installation To install the Door/Window Sensor: 1. Peel off the protective layer from the sticker on the accessory. 2. Stick the accessory onto the door/window frame. 3. Peel off the protective layer from the sticker on the magnet. 4.

  • Page 7: 5: Reset

    #5: Reset Resetting the Door/Window Sensor to factory defaults: Reset procedure allows to restore the accessory back to its factory settings including HomeKit pairing. 1. Open the cover. 2. Press the button 3 times then press and hold the button. Button 3.

  • Page 8: 6: Functionalities

    #6: Functionalities Opening/closing detection: The Door/window Sensor detects opening/closing using Hall effect sensor and reports it to your iOS device. Opening is detected by separating the sensor’s body and the magnet. Changing the state is indicated with one blink. Tamper detection: The Door/window Sensor detects tampering whenever the accesso- ry is detached from the surface or casing is opened and reports it to your iOS device.

  • Page 9: 7: Configurable Parameters

    #7: Configurable parameters 1. Opening/closing detection – LED indication This parameter allows choose if opening/closing is indicated by the built-in LeD diode. Available settings: 0 – indications disabled 1 – indications enabled 1 (indications enabled) Default setting: 2. Door/window state This parameter allows to set in what state is door/window when the magnet is close to the sensor.

  • Page 10: 8: Specifications

    #8: Specifications Power supply: 3.6V DC battery CAUTION using batteries other Battery type: eR14250 ½ AA than specified may result in explosion. eu directives compliance: RoHS 2011/65/eu Dispose of properly, ReD 2014/53/eu observing environ- mental protection Radio protocol: Bluetooth® low energy rules.

  • Page 11: 9: Regulations

    #9: Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including inter- ference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 12 All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to no- tify any individual or entity.
  • Page 13 Directive 2014/53/eu. The full text of the eu declaration of conformity is available at the following internet address: www.manuals.fibaro.com WEEE Directive Compliance Device labelled with this symbol should not be disposed with other household wastes.

Table of Contents