Related Manuals for Proceq hygropin
Summary of Contents for Proceq hygropin
-
Page 1: Operating Instructions
Operating Instructions Moisture Meter ... more than 50 years of know-how you can measure! Made in Switzerland... -
Page 2: Table Of Contents
5. Step by Step Guide “Relative Humidity Testing according to ASTM F2170” 6. Example of Test Report 7. Technical Specifications 8. Part Numbers and accessories 8.1 Units 8.2 Parts and Accessories 9. Maintenance and Support 9.1 Support Concept 9.2 Standard Warranty and Extended Warranty © by Proceq SA... -
Page 3: Safety And Liability
1.2 Liability and warranty Proceq’s “General Terms and Conditions of Sale and Delivery” apply in all cases. Warranty and li- ability claims arising from personal injury and damage to property cannot be upheld if they are due to one or more of the following causes: •... -
Page 4: Tutorial
% RH, a temperature difference of 1°C (1.8 °F) typically results in an error of 3 %RH on relative humidity. When using Hygropin, it is good practice to monitor the display for temperature stability. The probe should be given sufficient time to come to equilibrium with the environment to be measured. The larger the initial temperature difference between the probe and the environment, the more time is required for temperature equilibrium. -
Page 5: Overview Keypad
ENTER Confirm a selection and data capture. 3.4 Standard Display Depending on the settings the Hygropin is able to display: • relative humidity and temperature measured by two probes • calculate psychrometric parameters like dew / frost point etc. for both probes •... -
Page 6: Overview Screens & Menu Structure
3.5 Overview Screens & Menu Structure Standard Large H+T+Calc © by Proceq SA... -
Page 7: Detailed Menu Structure & Settings
Date separator “.” or ”/” Time format 24 h / 12 h Unit system Metric / English Real time clock does not auto adjust for daylight saving time. © by Proceq SA... - Page 8 Range (analog probe) … Calculated Parameters The Hygropin can calculate any of the following psychrometric parameters based on humidity and temperature: • Dew point (Dp) above and below freezing • Frost point (Fp) below freezing and dew point above freezing •...
- Page 9 • Select the target data batch with the • Press to trigger the Data Capture function • Data capture is confirmed on the Hygropin display Data Capture Data Batch 1 [Numbers of Records] … Data Batch 8 [Numbers of Records] Select data batch to be viewed Submenu Batch 1..8...
-
Page 10: Hygrolink
When recording data from two probes at the same time, the recording capacity per probe is cut in half. The Hygropin features two data logging mode: start-stop (recording ends when the memory is full) and loop (when the memory is full, the oldest record is dumped to make room for a new record) Data logging can be started and stopped from the keypad. -
Page 11: Step By Step Guide "Relative Humidity Testing According To Astm F2170
Check for stable value Measure ambient sleeve equilibrium (trend indicator) before condition record data Step 8: Report (Chapter 11, ASTM F2170-9) Use the Test Report template (chapter 6) to record and report all necessary informa- tion. © by Proceq SA... -
Page 12: Example Of Test Report
Instrument used: Last calibration date of probe Test performed: Name Test performed: Date Test performed: Company name Test performed: Company address Location Map Instructions: Indicate sensor locations with symbol and number of test hole. Show doors, rooms, columns or other location indicators. © by Proceq SA... -
Page 13: Technical Specifications
± 1.5 % RH / ± 0.3 K Response time < 15 s Dimension Ø 5 mm (Ø 0.2 in.) Cable length 200 cm (79 in.) Maximum air velocity at probe 20 m/s (3,935 ft /min) © by Proceq SA... -
Page 14: Part Numbers And Accessories
ASTM F 2170-09 Special note NIST traceability: All probes for the Hygropin are factory calibrated referring to the Swiss Calibration Service (SCS). An individual calibration certificate is included with each probe. SCS is accredited with the Swiss Federal Office of Metrology which is a signatory of the BIPM (http://www.bipm.org/) Under the Mutual Recognition Agreement NIST recognizes all registered in the BIPM database. - Page 15 © by Proceq SA...
- Page 16 Shanghai, 200050 Phone +86 21-63177479 +86 21 63175015 info-china@proceq.com www.proceq.com Subject to change without notice. Copyright © 2010 by Proceq SA, Schwerzenbach Part number: 820 780 01 E ... more than 50 years of know-how you can measure! Made in Switzerland...