Advertisement
7PZ IP
LED Display On/Off:
To set the LED display to turn off after 60 seconds, press the MODE but-
ton until "don" is displayed, press the UP button to display "doff". Now
the display will disappear after 60s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.
To set the display press the MODE button until "dXX" is displayed. Use
the UP or DOWN buttons to select either:
"don" = LED display on at all times.
"doFF" = LED display shuts off after 60 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display can
be read upside down.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "Stnd" or "rev" is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The 7PZ
IP has 12 DMX modes. See pages 9-21 for each modes' DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode, enter the MENU screen by
pressing and holding the MODE button. Press the UP or DOWN
buttons until "Menu Set ADDR" is displayed. Press the ENTER
button then use the UP or DOWN buttons to select your desired
DMX address. Press ENTER after you have found your desired
address.
3. After you have set your desired DMX addresss, select your
desired DMX channel mode. Access the main menu and press
the UP or DOWN buttons until "Menu UserMode" is displayed.
4. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. When you have found your desired DMX Channel mode
ADJ Products, LLC - www.adj.com - 7PZ IP User Manual Page 22
Operating Instructions
7PZ IP
press ENTER.
5. Please see pages 9-21 for DMX values and traits.
6. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
Dimmer Curve Setting:
1. Plug the fixture in and access the main menu. Press the UP or
DOWN buttons until "Menu Function" is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until "Dim Curve" is displayed,
and press ENTER.
3. Press the UP or DOWN buttons to find your desired dimmer
curve. Press ENTER to select and confirm. Please see the
Dimmer Curve Diagram Chart on page 31 to see the settings and
their respective beginning and ending fade times.
Color Balance Mode:
1. Plug the fixture in and access the main menu. Press the UP or
DOWN buttons until "Menu Function" is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until "Settings WhiteBal" is dis-
played, and press ENTER. Use the UP or DOWN buttons to scroll
through the RGBW colors. When you find a color you would like
to adjust press ENTER. Use the UP or DOWN buttons to adjust
the color output and press ENTER when done.
3. When you are finished making your adjustments press the MODE
button to exit this menu.
No DMX Hold:
This mode is used as a precaution mode, that in case the DMX signal
is lost, the operating mode chosen in this setup is the running mode
the fixture will go into when the DMX signal is lost. You can also set this
as the operating mode you would like the unit to return to when power
is applied.
1. Plug the fixture in and access the main menu. Press the UP or
DOWN buttons until "Menu Function" is displayed, and press
ENTER.
2. Press the UP or DOWN buttons until "No DMX Hold" is dis-
ADJ Products, LLC - www.adj.com - 7PZ IP User Manual Page 23
Operating Instructions
Advertisement
