JLG G5-18A Service Manual page 45

a. DIN 24° CONE (MBTL & MBTS)
TYPE/FITTING IDENTIFICATION
Material Type
DIN 24° CONE
FLARELESS
BITE (MBTL)
FITTING
STEEL
FITTINGS
WITH STEEL Type
MATING
COMPONENTS
DIN 24° CONE
FLARELESS
BITE (MBTS)
FITTING
NOTE: * ØA, ØB,C, & ØD thread dimensions for reference only.
** Refer to Section 2.8.15, "FFWR and TFFT Methods. " , for FFWR procedure requirements.
G5-18A, 2505
Tube Thread
ØA*
O.D. M Size
(mm) (Metric) (mm) (mm)
6 M12 x 1.5 10.50 12.00
8 M14 x 1.5 12.50 14.00
10 M16 x 1.5 14.50 16.00
12 M18 x 1.5 16.50 18.00
15 M22 x 1.5 20.50 22.00
18 M26 x 1.5 24.50 26.00
22 M30 x 2 27.90 30.00
28 M36 x 2 33.90 36.00
35 M45 x 2 42.90 45.00
42 M52 x 2 49.90 52.00
Tube Thread
ØA*
O.D. M Size
(mm) (Metric) (mm) (mm)
6 M14 x 1.5 12.50 14.00
8 M16 x 1.5 14.50 16.00
10 M18 x 1.5 16.50 18.00
12 M20 x 1.5 18.50 20.00
14 M22 x 1.5 20.50 22.00
16 M24 x 1.5 22.50 24.00
20 M30 x 2 27.90 30.00
25 M36 x 2 33.90 36.00
30 M42 x 2 39.90 42.00
38 M52 x 2 49.90 52.00
General Information and Specifications
DIN 24° CONE FLARELESS BITE FITTING
ØB* C* ØD*
(mm) (mm) Min
7.00 6.20
7.00 8.20
FFWR is the recommended method of
7.00 10.20
7.00 12.20
Torque values are application specific
due to variability in the fitting supplier,
7.00 15.20
coating, lubrication, and other physical
7.50 18.20
7.50 22.20
7.50 28.20
10.50 35.30
11.00 42.30
ØB* C* ØD*
(mm) (mm) Min
7.00 6.20
FFWR is the recommended method of
7.00 8.20
7.50 10.20
7.50 12.20 Torque values are application specific
due to variability in the fitting supplier,
8.00 14.20
coating, lubrication, and other physical
8.50 16.20
10.50 20.20
12.00 25.20
13.50 30.20
16.00 38.30
(WITH OR WITHOUT O-RING)
Torque
[Ft-Lb] [Nm]
Nom Max Min Nom
fitting assembly.
characteristic of the connection.
Consult Engineering on the
generation of torque values for the
particular application.
Torque
[Ft-Lb] [Nm]
Nom Max Min Nom
fitting assembly.
characteristics of the connection.
Consult Engineering on the
generation of torque values for the
particular application.
MAE9160
Flats From
Wrench
Resistance
Max
(F.F.W.R)**
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
Flats From
Wrench
Resistance
(F.F.W.R)**
Max
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
1.5 to 1.75
2-33