Timberwolf TW 18/100G Instruction Manual
  1. Manuals
  2. Brands
  3. Timberwolf Manuals
  4. Chipper
  5. TW 18/100G
  6. Instruction manual

Timberwolf TW 18/100G Instruction Manual

Wood chipper
Hide thumbs Also See for TW 18/100G:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
TW 18/100G WOOD CHIPPER
INSTRUCTION MANUAL
timberwolf-uk.com

Advertisement

Table of Contents
loading

Related Manuals for Timberwolf TW 18/100G

Summary of Contents for Timberwolf TW 18/100G

  • Page 1 TW 18/100G WOOD CHIPPER INSTRUCTION MANUAL timberwolf-uk.com...
  • Page 2 © Copyright Entec Industries Ltd 2015 The content of this publication may not be copied, reproduced, republished, posted, broadcast, transmitted or used in any way in any medium without the written permission of Entec Industries Ltd.

  • Page 3: Table Of Contents

    TIMBERWOLF CONTENTS TW 18/100G Section Page No. INTRODUCTION PURPOSE OF MACHINE MACHINE DIMENSIONS & SPECIFICATIONS PARTS LOCATION DIAGRAMS SAFE WORKING Operator’s Personal Protective Equipment Required Basic Woodchipping Safety General Safety Matters - Do’s and Dont’s Noise Test OPERATING INSTRUCTIONS Safe Transportation...

  • Page 4: Introduction

    - EqUIPMENT DAMAGE - DAMAGE TO PROPERTY - 3RD PARTY INjURIES This manual covers the operation and maintenance of the Timberwolf TW 18/100G. All information in this manual is based on the latest product information available at the time of purchase.

  • Page 5: Purpose Of Machine

    TIMBERWOLF TW 18/100G The Timberwolf TW 18/100G The Timberwolf 18/100G brushwood chipper is designed to chip solid wood material up to 100 mm in diameter. It is capable of chipping over 1.5 tonne of brushwood per hour. DIMENSIONS Serial No. Location...

  • Page 6: Parts Location Diagrams

    TIMBERWOLF TW 18/100G PARTS LOCATOR DISCHARGE BUCKET ROTOR HOUSING FUEL TANK FEED FUNNEL EXHAUST DISCHARGE TUBE jOCKEY DISCHARGE WHEEL CLAMPS ASSEMBLY HEAD ANTI-TRAP BAR RAIN FLAP CONTROL PANEL DRAW BAR RESTRAINING BELT CABLE GUARD ID PLATE SKID PLATE REFLECTORS...
  • Page 7 TIMBERWOLF TW 18/100G PARTS LOCATOR ROTOR CUTTER FAN SECTION (x 2) BLADES SPARE WHEEL DRIVE BATTERY BELTS DRIVE BELT COMPARTMENT TENSIONER PULLEY ROTOR DRIVE PULLEY ENGINE DRIVE PULLEY...

  • Page 8: Operator's Personal Protective Equipment Required

    TIMBERWOLF 125PH T IMBERWOLF TW 18/100G WARNING The chipper will feed material through on its own. To do this, it relies on sharp blades both on the feed rollers and the chipper rotor. To keep the blades sharp, only feed the machine with clean brushwood. DO NOT put muddy/dirty wood, roots, potted plants, bricks, stones or metal into the chipper.

  • Page 9: Safe Working

    TIMBERWOLF SAFE WORKING ü TW 18/100G GENERAL SAFETY MATTERS D O ’ S A N D D O N ’ T S ALWAYS stop the chipper engine before making DO NOT operate chipper unless available light is any adjustments, refuelling or cleaning.

  • Page 10: Noise Test

    TIMBERWOLF SAFE WORKING TW 18/100G NOISE TEST MACHINE: TW 18/100G NOTES: Tested chipping 50 mm x 50 mm corsican pine 1.5m in length Noise levels above 80dB (A) will be experienced at the working position. Wear ear protection at all times to prevent possible damage to hearing. All persons within a 4 metre radius must also wear good quality ear protection.

  • Page 11: Operating Instructions

    TIMBERWOLF OPERATING INSTRUCTIONS TW 18/100G DO NOT RIDE ON THE CHIPPER WHEN IT IS SAFE TRANSPORTATION WARNING BEING TOWED. WHEN towing a chipper the maximum speed limit is 60 mph. • ON rough or bumpy road surfaces reduce speed accordingly to protect your machine from •...

  • Page 12: Delivery

    TW 18/100G DELIVERY All Timberwolf TW 18/100G machines have a full pre - delivery inspection before leaving the factory and are ready to use. Read and understand this instruction manual before attempting to operate the chipper. In particular, read pages 5-7 which contain important health and safety information and advice.

  • Page 13: Stopping The Engine

    TIMBERWOLF OPERATING INSTRUCTIONS TW 18/100G STOPPING THE ENGINE Move throttle lever to ‘slow’ Push ‘on/off’ rocker switch position to ‘off’ position (pull start start only). Turn ignition key to ‘off’ position and remove (electric start engine only). Close fuel shutoff valve.

  • Page 14: Blade Wear

    “dull” change the blade(s). The TW 18/100G is fitted with 2 blades 177mm (7") long. They are 44 mm wide when new.

  • Page 15: Service Instructions

    MAINTENANCE THAT SHOULD BE APPLIED TO ANY PIECE OF MECHANICAL EQUIPMENT AND THE CHASSIS TO WHICH IT IS MOUNTED. AUTHORISED TIMBERWOLF SERvICE AGENTS ARE FULLY TRAINED IN ALL ASPECTS OF TOTAL SERvICE AND MAINTENANCE OF TIMBERWOLF WOOD CHIPPERS. YOU ARE STRONGLY ADvISED TO TAKE YOUR CHIPPER TO AN AUTHORISED AGENT FOR ALL BUT THE MOST ROUTINE MAINTENANCE AND CHECKS.

  • Page 16: Service Schedule

    RETURN TO DEALER Replace anvil when worn. NOTE: Your Timberwolf woodchipper is covered by a full 12 months parts and labour warranty. Subject to correct maintenance and proper machine usage, the bearings are guaranteed for 12 months regardless of hours worked by the machine. In conditions of 'heavy usage' - i.e. in excess of 500 hours per year - it is recommended that the bearings are changed annually to ensure that the machine retains optimum working performance.

  • Page 17: Spares

    Inspect the lifting eye prior to each use - DO NOT USE IF DAMAGED. CHECK FITTINGS The Timberwolf TW 18/100G is subject to large vibrations during the normal course of operation. Consequently there is always a possibility that nuts and bolts will work themselves loose. It is important that periodic checks are made to ensure the security of all fasteners.

  • Page 18: Copper Ease Safety Information

    SERVICE INSTRUCTIONS TIMBERWOLF TW 18/100G COPPER EASE SAFETY INFORMATION Product name: Copper Ease. Copper Ease contains no hazardous ingredients at or above regulatory disclosure limits, however, safety precautions should be taken when handling (use of oil-resistant gloves and saftey glasses are recommended - respiratory protection is not required).
  • Page 19 SERVICE INSTRUCTIONS TIMBERWOLF TW 18/100G BATTERY SAFETY INFORMATION...cont. 1. Storage and transport the positive output of the charger. Connect the - Batteries are filled with acid. negative terminal accordingly. - Always store and transport batteries upright - Switch on the charger only after the battery has...

  • Page 20: Change Blades

    NOTE: There will normally be a rapid drop in tension during run-in period for new belts. When new belts are fitted, check the tension every 2 - 3 hours and adjust until the tension remains constant. Belt failures due to lack of correct tensioning will not be covered under your Timberwolf warranty. Remove belt guard.

  • Page 21: Warranty Statement

    Industries Ltd as a hire chipper or long term demonstrator – in these situations they are duly authorised to transfer any remaining warranty period to their first end user. Any warranty offered by the Timberwolf Dealer beyond the original 36-month period will be wholly covered by said Dealer.

  • Page 22: Ec Declaration Of Conformity Certificate

    TIMBERWOLF TW 18/100G CERTIFICATE OF CONFORMITY...

  • Page 23: Identification Plate

    TIMBERWOLF TW 18/100G IDENTIFICATION PLATE...

  • Page 24: Decals

    TIMBERWOLF DECALS TW 18/100G Decal Description Decal Description 18393 New drive belts need re-tensioning. When new belts are fitted Hot exhaust check tension every 2-3 hours & adjust until tension remains constant. 2949 Lifting eye is designed to lift the machine’s weight only.
  • Page 25 DECALS TIMBERWOLF TW 18/100G Decal Description Decal Description P656 P653 Danger. Do not use this Danger. machine without the Rotating blades inside. discharge unit fitted. failure Stop engine and remove key to comply may result in before removing serious inury or damage.

  • Page 26: V-Belt Tensioning Data Table

    5. Take the reading from the deflection scale of the tension meter (read at the lower edge of the 'o'-ring) & compare this value with that given in the table. 6. Tighten or loosen belts as required following procedure given in this operator's manual. Tension gauges are available from Timberwolf spares, quoting part no. 18091 Rotor Pulley Belt Tensioner...

  • Page 27: Parts Lists

    TIMBERWOLF TW 18/100G PARTS LISTS The following illustrations are for parts identification only. The removal or fitting of these parts may cause a hazard and should only be carried out by trained personnel. Page No. BELT TENSIONER CHASSIS CHASSIS - DRAWBAR...
  • Page 28 TIMBERWOLF BELT TENSIONER TW 18/100G Item Part No Part Name q’ty 2988 M8/90 Bolt 0415 Heavy Washer 0491 Bearing 6205 0411M Pulley 0472M Pulley Boss N/A to purchase Slider 0469MS Slider Block 1342PS End Plate made in production Washer 0476...
  • Page 29 CHASSIS TIMBERWOLF TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty 19775 N/S Mudguard 0351 M8/30 Bolt 0350 M8/25 Bolt 0856 M5/20 Pan Pozi 0714 M8 Mudguard Washer 18922 Reflector 19689 Rain Flap Support 0236...
  • Page 30 27 CHASSIS - DRAWBAR TIMBERWOLF TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty P*75 jockey Wheel 19600 ID Plate 0382 M10/30 Bolt 0067 Pop Rivet 0701 M10 A Washer 0313 M12/100 Bolt 4345 M10 P Nyloc Nut...
  • Page 31 DISCHARGE TIMBERWOLF TW 18/100G...
  • Page 32 TIMBERWOLF DRIVE TRAIN TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty 0310 Belt Vee SPA 1060 0408 Taper Lock Bush 2012 1” 0410 Taper Lock Bush 2517 38 mm 0061 Key 1/4 x 1/4 x 1/2...
  • Page 33 ENGINE TIMBERWOLF TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty 19504 Engine 0712 M8 C Washer 19505 Muffler Kit 0354 M8/60 Bolt 4279 Muffler Deflector 0479 M8 P Nyloc Nut 0353 M8/50 Bolt 19506...
  • Page 34 TIMBERWOLF FUNNEL TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty 0693O Feed Tray 0046 M12 Plain Nut 0691O Funnel 0391 M6 T Nyloc Nut 0346 M8/20 Bolt 0709 M6 C Washer 0712 M8 C Washer...
  • Page 35 ROTOR TIMBERWOLF TW 18/100G Item Part No Part Name q’ty Item Part No Part Name q’ty 0959 Plastic Cap 1571 Fan Section 0884MS Front Bearing Housing 0386 M10/30 Caphead 0318 M12/20 Hex Set 0071MH Blade 0415 Heavy Washer 0065 Blade Bolts...
  • Page 36 TIMBERWOLF ROTOR HOUSING TW 18/100G Item Part No Part Name q’ty 19758FO Rotor Housing 1096FO Front Plate 0702 M12 A Washer 0045 M12 T Nyloc Nut 0524O Access Cover 0345 M8/18 Socket Caps 0105MH Anvil 0856 M5/20 Pan Pozi 18923 Reflector...

  • Page 37: Warranty Service Check Record

    TIMBERWOLF 125PH TIMBERWOLF WARRANTY SERVICE CHECK RECORD TW 18/100G 50 HOUR SERVICE Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: 11 MONTH WARRANTY SERVICE CHECK Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: 23 MONTH WARRANTY SERVICE CHECK...

  • Page 38: Service Record

    TIMBERWOLF 125PH T IMBERWOLF SERVICE RECORD TW 18/100G Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due:...
  • Page 39 Timberwolf Wood Chippers & Shredders Tomo Industrial Estate, Stowmarket, Suffolk IP14 5AY, United Kingdom T: +44 1449 765809 E: info@timberwolf-uk.com W: timberwolf-uk.com timberwolf-uk.com...

Table of Contents