AND WHERE SHOWN, - 3rd party injuries CAREFULLY FOLLOW THE This manual covers the operation and maintenance of the Timberwolf TW 13/75G. INSTRUCTIONS. All information in this manual is based on the latest product information available at the time of purchase.
PARTS LOCATOR 3 / 32 TW 13/75G GRIP MANUAL CANNISTER DISCHARGE HANDLE DISCHARGE BUCKET TOP ROTOR HOUSING GUARD FUNNEL BELT GUARD LIFTING EYE OPENING HANDLE PETROL TANK AIR FILTER COVER ROTOR HOUSING CATCH BOLT ENGINE SAFETY SWITCH EXHAUST GUARD THE TW13/75G HAS THE FOLLOWING FIXED GUARDS FOR PROTECTION OF THE OPERATOR, CHIPPER AND ENVIRONMENT: •...
SAFE WORKING 5 / 32 TW 13/75G OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT (PPE) • Chainsaw safety helmet (EN 397) fitted with mesh visor (EN 1731) and ear defenders (EN 352). • Work gloves with elasticated wrist. • Steel toe cap safety boots (EN 345-1).
STRING ROOTS BEDDING PLANTS NOISE TEST Machine: TW 13/75G Notes: Tested chipping 40mm x 40mm corsican pine 1.5m in length Noise levels above 80dB (A) will be experienced at the working position. Prolonged exposure to loud noise may cause permanent hearing loss. All...
ü ü Follow the recommissioning process before operation. NOTE: Regardless of storage time, all Timberwolf machines must be in a stable, level position to ensure the machine is unable to roll or move unintentionally during storage. C190-0187 25.01.2019 Rev: 1.0...
DELIVERY All Timberwolf TW 13/75G machines have a full pre - delivery inspection before leaving the factory and are ready to use. Read and understand this instruction manual before attempting to operate the chipper. In particular, read pages 5-6 which contain important health and safety information and advice.
OPERATING INSTRUCTIONS 9 / 32 TW 13/75G STARTING THE ENGINE • Turn the fuel valve to the ‘ON’ position. • Move the choke lever to the ‘CLOSE’ position. NOTE: Do not use the choke if the engine is warm or the air temperature is high.
40 degrees. When performing daily blade checks ensure blade edge is sharp and free from chips, if there is any evidence of damage, or the edge is “dull” change the blade(s). The TW 13/75G is fitted with one blade 177 mm (7") long.
This table is a troubleshooting guide to common problems. If your problem is not listed below, or is unresolved after following the guide, please contact your Timberwolf service agent, whose Timberwolf trained engineers can perform further fault finding. Before you call, please have this operating manual and the machine serial number ready.
SERVICE INSTRUCTIONS 12 / 32 TW 13/75G SERVICE SCHEDULE Daily SERVICE SCHEDULE Check Hours Hours Hours ü Check engine oil - top up if necessary (10W-30). ü Check for engine oil leaks. ü Check fuel level. ü Check feed funnel and belt guard are securely fitted.
CHECK FITTINGS The Timberwolf TW13/75G is subject to large vibrations during the normal course of operation. Consequently there is always a possibility that nuts and bolts will work themselves loose. It is important that periodic checks are made to ensure the security of all fasteners.
Petrol • Copper Ease MATERIAL SAFETY DATA SHEETS FOR HAZARDOUS MATERIALS SUPPLIED WITHIN TIMBERWOLF MACHINES ARE AVAILABLE ON REQUEST. REFER TO THESE FOR FIRST AID AND FIRE PROTECTION MEASURES. Always follow recommended procedures for safe handling, removal and disposal of hazardous materials. Safety precautions should be taken when handling hazardous materials (use of oil-resistant gloves and saftey glasses are recommended - respiratory protection is not required).
Retighten the screws to 30Nm (22lb/ft). This torque setting is vitally important to ensure your bolts come out at a later date. Timberwolf recommend you purchase a torque wrench for this and other jobs on the chipper. Remove Rotor Retaining Pin.
If it has become seriously rounded then it is appropriate to change it. Turning or replacing the anvil should be carried out by a Timberwolf dealer. ENGINE SERVICING All engine servicing must be performed in accordance with the Engine Manufacturer’s handbook provided with the machine.
TW 13/75G TIMBERWOLF NO-NONSENSE WARRANTY All new Timberwolf machines come with peace of mind built in. Our no-nonsense warranty is your guarantee of your Timberwolf wood chipper not letting you down. Your warranty statement is included in your manual pack. Please ensure you register your machine with your dealer to ensure you are eligible for the full Timberwolf warranty period.
DECALS 20 / 32 TW 13/75G Decal Description Decal Description 2944 Danger Warning. Beware of sharp blades when the Hot exhaust. rotor housing is open. 2949 Lifting eye is designed to lift the machine’s weight only. Do not use hoist hook on lifting eye. Use correctly rated safety shackle Warning.
Page 23
DECALS 21 / 32 TW 13/75G Decal Description Decal Description 18322 P637 Danger. Caution. Rotating blades inside. Stop Do not put road sweepings in engine and remove spark plug machine as grit will damage cap before removing discharge blades. unit.
Take the reading from the deflection scale of the tension meter (read at the lower edge of the 'o'-ring) & compare this value with that given in the table. Tighten or loosen belts as required following procedure given in this operator's manual. Tension gauges are available from Timberwolf spares, quoting part no. 18091 Rotor Pulley Engine Pulley...
WARRANTY SERVICE CHECK RECORD 24 / 32 TW 13/75G Model number: Serial number: Date of delivery/ Options/extras: handover: Dealer pre delivery check: Inspected by: 50 HOUR WARRANTY SERVICE CHECK Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due:...
SERVICE RECORD 25 / 32 TW 13/75G Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due: Authorised dealer stamp Date: Hours: Invoice number: Signature: Next service due:...
PARTS LIST 26 / 32 TW 13/75G PARTS LISTS THE FOLLOWING ILLUSTRATIONS ARE FOR PARTS IDENTIFICATION ONLY. THE REMOVAL OR FITTING OF THESE PARTS MAY CAUSE A HAZARD AND SHOULD ONLY BE CARRIED OUT BY TRAINED PERSONNEL. Page No. CHASSIS / ROTOR HOUSING...