Siemens SIWAREX FTA Device Manual page 56

Weighing Functions
Name
Max. waiting time for TIME
stand-still 1
Max. negative weight for BYTE
zero setting when
switching on
Max. positive weight for BYTE
zero setting when
switching on
Maximum negative BYTE
weight for zero setting
Maximum positive weight BYTE
for zero setting
Tare max. weight T- BYTE
Load cell type BYTE
Timeout digital LC WORD
Regulations STRING
[4]
Unit of measurement STRING
[4]
Stand-still range 2 REAL
Stand-still time 2 TIME
Max. waiting time for TIME
stand-still 2
Stand-still range 3 REAL
Stand-still time 3 TIME
Minimum waiting time at TIME
stand-still 3
Smallest set weight ∑min REAL
Distribution value dt REAL
5-44
Type Address Default
DBB100 2000
DBB104 10
DBB105 10
DBB106 1
DBB107 3
DBB108 100
DBB109 0
DBW110 240
DBB112
"----"
DBB118 kg
DBD124 0,02
DBB128 1000
DBB132 500
DBD136 0,02
DBB140 1000
DBB144 500
DBD148 100
Wizzard:
= WB
max
DBD152 0,1
Range of Values / Explanation
If there is no stand-still 1, the respective weighing
instruction will be rejected with an operational error
with a setting of 0 and otherwise, the waiting time
will elapse. If the max. waiting time has elapsed and
there is still no stand-still, an error message is sent.
For weighing instructions that are activated by an
operator, a setting around 2000 ms is reasonable.
(During the weighing cycle, this time is not
monitored)
Negative range for Switch-on zero setting device [in
% of weighing range ]
max
(Entry of Pos- + Neg. zero set value must not
exceed 20% with country code "OIML")
Positive range for Switch-on zero setting device [in
% of weighing range ]
max
(Entry of Pos- + Neg. zero set value must not
exceed 20% with country code "OIML")
Negative range for zero setting device [in % of
weighing range ]
max
(Entry of Pos- + Neg. zero set value must not
exceed 4% with country code "OIML")
Negative range for zero setting device [in % of
weighing range ]
max
(Entry of Pos- + Neg. zero set value must not
exceed 4% with country code "OIML")
Subtractive tare device range
[in % of WR with multi-range scale]
max
[in % of WR with multi-resolution scale]
1
(Value must not exceed 100%)
Range of the additive tare device
[in % of WB , only a single range scale is permitted
1
in conjunction with regulation code "OIML"]
(Value must not exceed 250%)
0: analog load cell
1: METTLER TOLEDO type WM or WMH
2: WIPOTEC digital load cell
3: PESA digital load cell
>3: analog load cell
Timeout in ms for receiving the cyclic weight value
of the digital load cell
"OIML" : = Regulation Code OIML
"----": = No Regulation Code
Stand-still range 2 cm weight unit Effective when
starting a weighing procedure
msec
Max. waiting time for stand-still when starting a
weighing (ms)
0: No waiting time active
Stand-still range 3 cm weight unit Effective after
switching off fine current.
msec
Minimum waiting time at stand-still after switching
off fine signal (msec)
0 No waiting time active
Must only be entered with AWI totalizing operating
mode.
dt can correspond with the numerical step in WB
Re-
ference
5.2.25
5.2.26
5.2.27
5.2.28
5.2.29
5.2.30
5.2.31
5.2.32
5.2.33
5.2.34
5.2.35
5.2.36
5.2.37
5.2.38
5.2.39
5.2.40
5.2.41
5.2.42
nmax
SIWAREX FTA