Related Manuals for GE JSC1300
Summary of Contents for GE JSC1300
- Page 1 Owner’s Manual Supervised Security System Model JSC1300 DISARM LIGHTS LIGHTS PANIC...
- Page 2 FCC Caution Contents This equipment generates and uses radio frequency To be certain of the number of devices that may be Introduction ....................4 energy, and if not installed and used properly, that is, connected to a line, as determined by the total Installation ......................
-
Page 3: Locating Security System Components
• Up to 30* magnetic switch operated Wireless Door/Window Sensors. • Up to 30* Wireless PIR Motion Detectors. • Optional X10 and/or GE Home Automation modules such as plug-in lamp and appliance modules and wired-in replacement wall switches can be added to the Kitchen system, to flash house lights on and off when the alarm trips. -
Page 4: Installation
Installation Installation Security Console Fitting the backup batteries Attaching cables Install 4 AA alkaline batteries (not supplied) in the battery compartment. It is not A telephone cord terminated at each end with an RJ11 connector is provided for necessary to disconnect power to the Console when fitting or replacing batteries. telephone connection. -
Page 5: Overview
* for each number entered. 0-9 Used for all number entries. **** On Used to send a X10/GE On message or to enter am in a time. 12:00 am Off Used to send a X10/GE Off message or to enter pm in a time. - Page 6 Installation Installation First Menu Level Sub-menus After pressing a menu up/down button and entering the PIN, the First Level menu is Once you’ve arrived at your desired first level menu and pressed OK, you can select the displayed, as shown below: sub-menus under that menu item.
-
Page 7: Registering Door/Window Sensors
Installation Installation Initializing Keyfob Remotes Initializing Door/Window Sensors Press and hold the ARM button on the Keyfob remote for 3-4 seconds Pry the two halves of the Door/Window Sensor apart and install and then release it. This initializes the remote and picks a random 2 AAA alkaline batteries inside. - Page 8 Installation Installation Now move the magnet away from the Door/Window Sensor. The Console acknowledges Installing the Door/Window Sensors that it has been registered with a chime and by displaying ZONE 1 SET. Repeat this for any other Door/Window Sensors you want to register. The display increments to ZONE 2 SET, etc.
-
Page 9: Removing Motion Detectors
Installation Installation Initializing Motion Detectors Now simply press the TEST button on the back of the Motion Detector (or turn the unit over so that it sees motion). The Console will acknowledge that it has been registered by displaying (for example) ZONE 3 SET. Remove the cover on the front of the Motion Detector and install 2 AA alkaline batteries in the compartment. -
Page 10: Installing The Motion Detector
Installation Installation Installing the Motion Detector Hard-Wired Inputs You can also connect two hard-wired magnetic contact switches to the console. • Attach the Motion Detector to a wall at a height of 5 to 6 ft. using the mounting bracket and screws provided. -
Page 11: Setting The Clock
Installation Installation Setting the Clock Setting the phone numbers Press either of the Menu up/down buttons (under the lid to the bottom left of the display). Press either of the Menu up/down buttons (under the lid to the bottom left of the display). The display then shows ENTER PIN (Personal Identification Number) in the top line. - Page 12 Installation Installation Recording your outgoing phone message Press 1 for RECORD , then press OK. The display shows: Press either of the Menu up/down buttons (under the lid to the bottom left of the display). PLEASE WAIT The display then shows ENTER PIN (Personal Identification Number) in the top line. ENTER PIN Then: 12:00 am...
-
Page 13: Clearing The Memory
Installation Installation Changing your Personal Identification Number (PIN) Clearing the memory Press either of the Menu up/down buttons (under the lid to the bottom left of the display). Press either of the Menu up/down buttons (under the lid to the bottom left of the display). The display then shows ENTER PIN (Personal Identification Number) in the top line. -
Page 14: Setting Options
(Default 30 seconds) 2. SIREN OFF (Silent Alarm, but Console still dials out) EXIT DELAY (Default 60 seconds) HOUSECODE For X10/GE Module (Chosen by Menu up/down buttons) LIGHTCODE For flashing lights (Chosen by Menu up/down buttons) DIAL DELAY (Default 5 seconds) -
Page 15: Setting Timers
Installation Installation Setting Timers to turn lights on and off (requires X10/GE Modules) To enter a new timer you must be on the NEW TIMER screen. Then press OK. The display shows UNIT NUMBER on the top line. Using the number keys, enter a valid number (1-16) and press OK. -
Page 16: Canceling Timers
Installation Installation Reviewing/Canceling Timers You can cycle through (Review) your stored timers by pressing the up or down Menu buttons. This will show the stored timers in the form below: Press either of the Menu up/down buttons (under the lid to the bottom left of the display). 12ON 12:34am The display then shows ENTER PIN (Personal Identification Number) in the top line. -
Page 17: Using The System
Using the system Using the system Arming the system If there’s a problem Press ARM HOME on the Console to arm ALL Door/Window Sensors instantly. Motion If a door or window is open and you try to arm the system the display looks as below. Detectors will not trip the system when it is armed in the ARM HOME mode. - Page 18 • A loud siren sounds. • Lights (set to the security code) flash on and off (if you set up X10/GE modules). Controlling lights and appliances See pages 26, 36, and 37. If you install one or more Lamp Modules (sold separately), see pages 36 and 37, you can •...
- Page 19 Testing The GE Module(s) Testing The X10 Module(s) Make sure the lamp's switch is on. Plug the GE Module into the same wall outlet as your Make sure the lamp's switch is on. Plug the X10 Lamp Module into the same wall outlet as your Console’s power supply, press the number button on the Console that...
-
Page 20: Security Console
You will NOT lose its stored telephone numbers, recorded message, or installed If you install X10 or GE modules (sold separately), see pages 36 and 37, you can control sensors and remotes, but you WILL need to reset the clock for the correct time of day. -
Page 21: Problem Zones
Battery Information Troubleshooting Door/Window Sensors and Motion Detectors PROBLEM SOLUTION If the system does not arm. • Check that the indicator on the Remote Battery Replacement turns on when you press ARM. If a zone has not reported in to the Console during the last four hours, the display will Replace the batteries and reregister show PROBLEM and the appropriate zone number when you try to arm the system. -
Page 22: Troubleshooting
Troubleshooting Troubleshooting PROBLEM SOLUTION PROBLEM SOLUTION If the alarm trips when you enter the Arm the system in the AWAY mode. If you do not hear a beep from the Console Reinitialize the remote (see page 12). house before you have time to disarm it. when you press ARM to install a Remote. -
Page 23: Expanding Your System
Troubleshooting Expanding Your System The GE Security System can flash lights on and off when the alarm trips. You connect the PROBLEM SOLUTION lights you want it to control to X10 and/or GE Lamp Modules, Wall Switch Modules, and Screw-in Modules (sold separately). The SC13A Security Console acts as a “Transceiver”... - Page 24 Notes Notes...
- Page 25 Jasco Products Company 311 N.W. 122nd Oklahoma City, OK 73114 JSC1300 -02/05 Supervised Security System...