Norac UC5 Installation Manual
Spray height control system.
john deere gs2 2600, 1800 and gs3 2630
jd 4630 display kit
Hide thumbs
Also See for UC5:
- Operator's manual (68 pages) ,
- Installation manual (50 pages) ,
- Instruction manual (35 pages)
Related Manuals for Norac UC5
Summary of Contents for Norac UC5
- Page 1 John Deere GS2 2600, 1800 and GS3 2630 JD 4630 Display Kit Installation Manual GS2-SP02...
- Page 2 4630 Display Kit) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...
-
Page 3: Table Of Contents
Item C26: 43240-26 – Cable UC5 Switch Box ....................7 Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT ..................8 Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M ................9 ... -
Page 4: Introduction
UC5 Spray Height Control Installation Manual. This manual provides instructions to interface the UC5 Control Module to the John Deere GS2 2600, 1800 and GS3 2630 Display. For installation of the rest of the UC5 Spray Height Control System please refer to the sprayer specific manual provided with the kit. -
Page 5: Technical Specifications
2 Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 6: Installation
3 Installation CANbus Interface Installation 1. Securely mount the control module (E01) inside the sprayer cab. 2. Tee the CANbus interface cable (C40) in to the John Deere CANbus. The John Deere CANbus connection can be found in the right hand armrest. The connector is a 4 pin Deutsch plug labeled “CAN 2”. -
Page 7: Switch Box Installation
Switch Box Installation 1. This step of the installation assumes that the input module and all required cables are installed. 2. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge from the face of the 12 pin Deutsch plug. The wedge is removed by inserting a small flat implement underneath the wedge and lifting it up. -
Page 8: Cable Drawings
4 Cable Drawings Item C25: 44602-01 – Switch Remote Hand Control... -
Page 9: Item C26: 43240-26 - Cable Uc5 Switch Box
Item C26: 43240-26 – Cable UC5 Switch Box... -
Page 10: Item C40: 43260-08 - Cable Uc5 Canbus 4 Pin Dt
Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT... -
Page 11: Item C41: 43210-01 - Cable Uc5 Network 18 Awg - 1M
Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M... - Page 12 Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P 0A6 United States NORAC, Inc. Phone: (+1) 952 224 4142 Toll Free: 1 866 306 6722...
Need help?
Do you have a question about the UC5 and is the answer not in the manual?
Questions and answers