1. Manuals
  2. Brands
  3. General DataComm Manuals
  4. Network Card
  5. spectracomm ip
  6. Installation & operation manual

General DataComm spectracomm ip Installation & Operation Manual

Router card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
6SHFWUD&RPP#,3#
ROUTER CARD
Installation & Operation Manual
076R200-000
Issue 2
October 2002

Advertisement

Table of Contents
loading

Summary of Contents for General DataComm spectracomm ip

  • Page 1 6SHFWUD&RPP#,3# ROUTER CARD Installation & Operation Manual 076R200-000 Issue 2 October 2002...
  • Page 2 General DataComm, Inc. The information in this document is subject to change without notice. General DataComm assumes no responsibility for any damages arising from the use of this document, including but not limited to, lost revenue, lost data, claims by third parties, or other damages.

  • Page 3: Table Of Contents

    Initializing the SC-IP for Configuration ................3-2 Configuring SC-IP with Smart CLI ..................3-3 Access to SC-IP Command Line Interface (CLI).............3-3 Static Routing in a Frame Relay T1 Network ..............3-4 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 4 Command Overview ......................B-4 Clear Commands......................B-4 Configure Accounts Commands ..................B-5 Configure Frame Relay Commands.................B-6 Configure Interfaces Commands ..................B-7 Configuration Tutorials ......................B-8 Example 1: Configuring SC-IP for IP Routing (Frame Relay)........B-8 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 5 Table of Contents Example 2: Configuring SC-IP for IP Routing (PPP) ........... B-12 Example 3: Configuring SC-IP for LAN-X Mode ............B-15 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 6 Table of Contents SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 7 The information in this manual has been carefully checked and is believed to be entirely reliable. However, as General DataComm improves the reliability, function and design of its products, it is possible that information may not be current. Check the General DataComm website at http://www.gdc.com for updated product information or contact your General DataComm...

  • Page 8: Preface

    If a wrist strap is not available, periodically touch an unpainted metal surface on the equipment. Never use a conductive tool, like a screw driver or paper clip to set switches. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...

  • Page 9: Compliance

    If so, the telephone company will notify you in writing. All repairs or modifications to the equipment must be performed by General DataComm. Any other repair or modification by a user voids the FCC registration and the warranty.

  • Page 10: Electromagnetic Compatibility

    Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada. NEBS Compliance Certified by independent labs for NEBS compliance to standards: GR63 - Physical Protection GR1089 - EMC and Safety viii SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 11: Support Services And Training

    Support Services and Training Support Services and Training General DataComm offers two comprehensive customer support organizations dedicated to pre-and post-sale support services and training for GDC products. Corporate Client Services and Factory- Direct Support & Repair assist customers throughout the world in the installation, management, maintenance and repair of GDC equipment.
  • Page 12 Preface Support Services and Training SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 13: Chapter 1: Introduction And Specifications

    Specifications About this Document This document describes in detail the initial feature set for the SpectraComm IP Router Card. Briefly mentioned are several additional features (DDS support and modem facilities) which are planned for a future release. For more information on the availability and operation of these additional features, refer to later issues of this document or contact your GDC Sales Representative.

  • Page 14: Features And Benefits

    • Supports major alarm reporting. • Provides access to the DDS network using an integral synchronous DTE interface to an external 56/64Kbps DSU. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 15: Csu/Dsu Functionality

    The modem port is designed to accept dial-up connections for direct VT-100 access (Hyperterm) or PPP session. Note For configuration of SC-IP interfaces, refer to Chapter 2: Installation and Set-Up. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 16: Sc-Ip Router Applications

    Network CRAFT DEVICES DEVICE 1 Future Use REMOTE DIAL-IN USER DEVICE 2 MODEM MANAGEMENT Public TERMINAL DEVICE 8 Switched Telephone MODEM Network Figure 1-1 Typical Deployment of SC-IP Router SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 17: Sc-Ip Lan-X Applications

    ETHERNET SPECTRACOMM 2000 SC-IP HOST TERMINAL MANAGED SERVER CRAFT DEVICES DEVICE 1 ETHERNET DEVICE 2 SPECTRACOMM 2000 SC-IP DEVICE 8 Figure 1-2 Typical Deployment of SC-IP in LAN-extension Mode 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 18: The Sc-Ip Front Panel

    Steady On (GREEN) indicates the Ethernet port (1 or 2) is connected and not passing data. SC-IP E1 ON (BLINKING) Blinking On (GREEN) indicates the Ethernet port (1 or 2) is connected and actively passing data. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 19: Sc-Ip Applications With Ethernet Switching

    LAN DEVICE 8 REMOTE DIAL-IN USER CRAFT DEVICE 1 MANAGEMENT TERMINAL CRAFT DEVICE 2 Public Switched Telephone Network CRAFT DEVICE 8 MODEM Figure 1-3 Deployment of SC-IP and SC-ES 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 20: Technical Specifications

    Technical Specifications Technical Specifications The following table describes the physical, operational, and environmental specifications for the SpectraComm IP. Conforming to these specifications ensures maximum system performance and reduces the chances of mechanical breakdown and personnel hazard. Table 1-2 SC-IP Specifications (Initial Feature Set)
  • Page 21 SC-IP Card Designed for NEBS Level III Compliance Compatibility FCC Part 68 approved; FCC Part 15 approved. UL Listed; CUL listed. Compliance with Bell Pub. 62310 and ANSI T1.410 standards 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 22 Introduction and Specifications Technical Specifications 1-10 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 23: Chapter 2: Installation & Connections

    Do not install the shelf directly above equipment such as power supplies, which generate large amounts of heat. SpectraComm IP Router Card Installation Guidelines • The SC-IP card may be installed in any slot in a SpectraComm shelf or enclosure.

  • Page 24: Unpacking Instructions

    SpectraComm IP Router Card LAN, T1/FT1 076P032-001 (rack-mounts in SC2000 or SC5000 shelf) (PPP , Ethernet) SpectraComm IP Router Card (for RA-1000 Enclosure) 076A032-015 Factory-installed Default Configuration Profile (01-99) Router or LAN-X modes 076U032-D## Cable, 8-pin modular to 8-pin modular straight-thru...
  • Page 25 MS-2 Mod. 12, (Mass Term) -48, -60 Vdc (redundant P .S.) 010M076-001 MS-2/DC Export Shelf -48, - 60 Vdc 010B152-001 DPS-11 Power Supply (2) 041P050-001 Z3-S-16DB25, 16-Slot DB25 (2) 010C339-001 UNIV Z1-50 Pin, 16-Slot 50 Pos 010C377-001 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 26: Shelf And Card Connections

    SC 2000 SHELF BACK PANEL TERM SERVER PORT SC-IP (To Craft Devices) SC 1001 ENCLOSURE BACK PANEL ETHERNET PORTS NTWK A NTWK B CRAFT PORT TERM Figure 2-1 SpectraComm Card and Shelf Connections SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 27: Interface Port Descriptions

    521A device for DDS network connections (a RJ45-to-DB25M adapter cable is required). The table below describes the AUX/Sync DTE port pinouts. Table 2-4 AUX/Sync DTE Port Pinouts RJ45 Pin Signal DB25M Pin Tx Clk Rx Clk 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 28 In order to establish a Craft session via the SC-IP’s Terminal Server port, some devices will require control leads tied to the appropriate state. For example, a device with a 25-pin terminal connection may need one or more pins driven to the EIA high state. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...
  • Page 29 Table 2-7 Ethernet LAN Port 1 & Port 2 Pinouts Signal Direction Description To SC-IP Receive Data To SC-IP Receive Data From SC-IP Transmit Data From SC-IP Transmit Data 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 30: Interface Cables & Adapters

    PORT 3 RJ-45 8-POS WHT/GRY BLU/RED RED/BLU RS-561 PORT 4 RJ-45 8-POS ORG/RED RED/ORG GRN/RED RS-561 PORT 5 Figure 2-2 Terminal Server DTE Cable Pinouts (Sheet 1 of 2) SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 31 PORT 6 RJ-45 8-POS GRY/RED RED/GRY BLU/BLK RS-561 PORT 7 RJ-45 8-POS BLK/BLU ORG/BLK BLK/BRN RS-561 PORT 8 Figure 2-3 Terminal Server DTE Cable Pinouts (Sheet 2 of 2) 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 32 PORT 3 RJ-45 8-POS WHT/GRY BLU/RED RED/BLU RS-561 PORT 4 RJ-45 8-POS ORG/RED RED/ORG GRN/RED RS-561 PORT 5 Figure 2-4 Terminal Server DCE Cable Pinouts (Sheet 1 of 2) 2-10 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 33 Y-Adapter Cable Pinouts Shelf Connector Switched Network T1 Line Signal Direction (RJ48) (RJ11) (RJ48) T1-Rx-Ring From line T1-Rx-Tip From line T1-Tx-Ring To Line T1-Tx-Tip To Line Modem-Tip two-wire bi-directional Modem-Ring 076R200-000 SpectraComm IP Router Card 2-11 Issue 2 Installation and Operation Manual...

  • Page 34: Sc-Ip Power-Up

    As a security precaution, do not connect the Modem and AUX ports to the network until the default password has been changed via the Craft port. (See Chapter 3: SC-IP Configuration Overview 2-12 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 35: Chapter 3: Sc-Ip Configuration

    Show system parameters _______________________Utility Commands______________________________ batch Store and/or run commands in batch mode exit Exit SpectraComm IP Command Line Interface flash Copy flash files/select flash boot file reboot Halt and perform a reboot tftp Enable/Disable TFTP Server (supports flash upgrade)

  • Page 36: Initializing The Sc-Ip For Configuration

    ASCII file, simplifying the configuration of multiple SC-IPs. This function can also be used to archive configuration data for specific unit or as a baseline for modified configurations. Refer to Appendix A, Application Guidelines Batch Up/Download Overview SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 37: Configuring Sc-Ip With Smart Cli

    3. Modify default admin and supervisor accounts by typing: [new admin password] configure accounts add admin [new suprv password] configure accounts add supervisor 4. Add a user account and password by typing: [name] [password] configure accounts add 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 38: Static Routing In A Frame Relay T1 Network

    7. Configure the Frame Relay LMI by typing: [cisco] configure frame-relay lmi type s0 configure frame-relay lmi n391 s0 configure frame-relay lmi n392 s0 configure frame-relay lmi n393 s0 [10] configure frame-relay lmi t391 s0 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 39 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 40 DEVICE 3 DEVICE 1 DEVICE 2 DEVICE 4 MANAGED CRAFT DEVICES DEVICE 7 DEVICE 5 DEVICE 6 DEVICE 8 Figure 3-1 SC-IP Router in a Typical Frame Relay T1 Network SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 41: Static Routing In A Leased Line (Ppp) T1 Network

    6. Enable the Ethernet interface by typing: configure interfaces enable ethernet0 Configure the serial0 interface for PPP by typing: configure interface link-encap serial0 ppp 8. When the Warning message appears, type Y. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 42 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 43 DEVICE 3 DEVICE 1 DEVICE 2 DEVICE 4 MANAGED CRAFT DEVICES DEVICE 7 DEVICE 5 DEVICE 6 DEVICE 8 Figure 3-2 SC-IP Router in a Typical PPP T1 Network 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 44: Lan-Extension For T1 Flat Networks

    [###.###.###.###] 5. Enter a description of the Ethernet interface by typing: [your_description] configure interfaces description ethernet0 6. Enable the Ethernet interface by typing: configure interfaces enable ethernet0 3-10 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 45 Once spanning tree is enabled, additional configurable options are available for that function. Do not change these additional spanning tree options from the default settings unless you have a comprehensive understanding of the spanning tree protocol. (Ref. IEEE 802.1D) 076R200-000 SpectraComm IP Router Card 3-11 Issue 2 Installation and Operation Manual...
  • Page 46 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. 3-12 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 47 MANAGEMENT CRAFT DEVICES ADDRESS 172.16.5.10/16 SC-IP General DEVICE 1 DataComm T1 INTERNAL TIMING DEVICE 2 DEVICE 8 Figure 3-3 SC-IP LAN-Extension in a Flat T1 Network (No Routing) 076R200-000 SpectraComm IP Router Card 3-13 Issue 2 Installation and Operation Manual...
  • Page 48 SC-IP Configuration Configuring SC-IP with Smart CLI 3-14 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 49: Chapter 4: The Web Interface

    Ethernet LAN or T1 (WAN) connection. 4. SC-IP permits up to eight authorized users and supervisors in simultaneous web management sessions. If eight sessions are in progress, any additional users will be denied access. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 50: Starting A Web Session

    (Admin commands must be entered via Telnet or Craft interface.) Note Access will be denied to any user or supervisor if there are already eight web sessions in progress. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 51: Sc-Ip Web Screens

    You must then logout and login to start a new web session. Note Whenever you use your browser’s Reload button, the system will always reload the Administration screen. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 52: Administration Web Screen

    Commands Save Button Click to save the administration data to the unit. Reset Button Click to discard unsaved edits and reset options to previous settings. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 53: Statistics Web Screen

    Read-only display of receive traffic conditions detected at the selected interface. Transmit Traffic Read-only display of transmit traffic conditions detected at the selected interface. Errors Read-only display of errors detected at the selected interface. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 54: Command Line Web Screen

    Configuration commands that are restricted to ADMIN mode will not be displayed . You must logout of the web interface and make a Telnet or terminal connection in ADMIN mode to access/execute those commands. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...

  • Page 55: Interface Web Screen

    At the web-based command line screen, up to 72 alphanumeric and other printable characters can be entered to describe an interface. Illegal characters include any non-printing characters, such as CTRL and ALT. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 56: Ip Static Route Web Screen

    (synchronous DTE port) or serial1. nnn (DLCI nnn on T1 port) modem0 (modem port) Line Protocol Displays the Layer 2 protocol for the interface (UP or DOWN). Type Displays the type of route. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 57: T1 Parameters Web Screen

    Select Timeslot: 1 - 24 Save Button Click to save the T1 configuration parameters to the unit. Reset Button Click to discard unsaved edits and reset options to previous settings. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 58: Terminal Server Web Screen

    At the web-based command line screen, up to 72 alphanumeric and other printable characters can be entered to describe a port. Illegal characters include any non-printing characters, such as CTRL and ALT. 4-10 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...

  • Page 59: Dlci Web Screen

    Displays the available sub-interfaces: serial0 or serial1. DLCI Displays the configured DLCI numbers for the associated sub-interface. IP Encapsulation Displays the IP encapsulation protocol for the associated sub-interface. 076R200-000 SpectraComm IP Router Card 4-11 Issue 2 Installation and Operation Manual...

  • Page 60: Lmi Web Screen

    Repeat steps 1-3 for the remaining interface. 4. When all desired changes have been made, click the Save button to save the LMI configuration data to the unit. 4-12 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 61: Traffic Shaping

    Repeat steps 1-3 for the remaining interface. 4. When all desired changes have been made, click the Save button to save the Traffic Shaping configuration data to the unit. 076R200-000 SpectraComm IP Router Card 4-13 Issue 2 Installation and Operation Manual...
  • Page 62 The Web Interface SC-IP Web Screens 4-14 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 63: Appendix A:application Guidelines

    Console authorization may be turned on in Admin mode by the configure accounts console enable command string. For Telnet connections, username/password login will always be required. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 64: Sc-Ip Default Configurations

    Add admin Escape sequence ^^^ Configuration Add supervisor Auto Reboot Disabled To enable, uncomment the Add gdc batch file line: # reboot Console (craft port) Authentication Disabled Spanning Tree Disabled SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 65: Using Sub-Interfaces For Frame Relay Pvcs

    IP-address ::= < > < > with a subnet mask of 192.168.11.1 255.255.255.0 Example: Shortened IP notation: 192.168.11.1/24 where the indicates that the first 3 octets comprise the network prefix. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 66 IP network if configured with DVMRP, PIM or MOSPF Table A-4 Private IP Addressing Network Class Private RFC 1918 Addresses 10.0.0.0 - 10.255.255.255 172.16.0.0 - 172.31.255.255 192.168.0.0 - 192.168.255.255 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 67: Establishing An Ip Address

    IP addresses or masks. LOCAL DEFAULT ROUTER NETWORK INCOMING 189.254.0.0 IP TRAFFIC 189.254.2.1 IP DESTINATION: 191.254.2.1 (NOT LOCAL) 189.254.2.4 Figure A-1 Using Subnet Masks 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 68: Ones Density Enforcement

    Application with 8(N+1) Enforcement Line Code Format Consecutive Enforcement B8ZS B8ZS Nx56K Consecutive None Nx64K Consecutive 8(N+1) Note The AMI line option code is not recommended for a 64kbps network rate. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 69: Batch Up/Download Overview

    Enter SUPERVISOR mode or ADMIN mode and activate the file transfer. 5. When the SC-IP# prompt returns to the screen, type batch show to view the downloaded commands. If desired, type batch run to execute the file. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 70: Troubleshooting Communications Problems

    SC-IP uses Java 1.1. If your Browser is Netscape 6.0 or later, Java will not be supported. You will need to acquire a Java plug-in in order to make a web connection with SC-IP. SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...

  • Page 71: Appendix B:cli Reference

    Show system parameters _______________________Utility Commands___________________________________ batch Store and/or run commands in batch mode exit Exit SpectraComm IP Command Line Interface flash Copy flash files/select flash boot file reboot Halt and perform a reboot tftp Enable/Disable TFTP Server (supports flash upgrade)
  • Page 72 When you type configure interfaces ip-address ? the screen will show the three required parameters and one optional parameter used to configure an IP address for an interface: Demo_unit%> configure interfaces ip-address ? SpectraComm IP Router Card 076R200-000 Installation and Operation Manual...
  • Page 73 Type show history to display a numbered history of the previous 20 commands. At the command prompt, type ![##] where ## is the history screen line number of the desired command. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 74: Cli Command Tables

    Clears login account statistics. clear login-stats (Must be in Suprv or Admin mode to execute this command.) Clears pvc counters. clear pvc-counters Clears the reboot counters. clear reboot-counter SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 75: Configure Accounts Commands

    Deletes username and password from accounts; Username and password are each 20 a/n chars max. Disables console user configure accounts console disable authentication. Enables console user configure accounts console enable authentication. 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 76: Configure Frame Relay Commands

    Optional parameter for Be bits per interval, excess (0-1536000) Enable traffic shaping [nnn] configure frame-relay ena-traffic Sub-interface name: serial [nnn] Disable traffic shaping configure frame-relay dis-traffic Sub-interface name: serial SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 77: Configure Interfaces Commands

    [n] frame-relay-dte Set link encapsulation for PPP for specified configure interfaces link-encap interface. [n] ppp Set link encapsulation for LAN-X for configure interfaces link-encap specified interface. [n] lanx 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...

  • Page 78: Configuration Tutorials

    If desired. type show T1 to check your current T1 entries. Modify, if needed. 3. Configure the Ethernet IP address and mask by typing: configure interfaces ip-address ethernet0 172.16.5.6 255.255.0.0 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 79 If a local router is used at the NOC instead of a SC-IP, consult your router documentation for static route configuration guidelines. Set up a static route at a remote site towards the NOC by typing: configure ip-route add serial0.17 128.1.0.0 255.255.0.0 128.1.1.10 1 076R200-000 SpectraComm IP Router Card Issue 2 Installation and Operation Manual...
  • Page 80 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. B-10 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 81 Frame Relay CRAFT DEVICES Network TERM1 192.160.1.12 DEVICE 1 DLCI 117 TERM2 DEVICE 2 TERM8 DEVICE 8 Figure B-1 Example: SC-IP Routing in a Frame Relay T1 Network 076R200-000 SpectraComm IP Router Card B-11 Issue 2 Installation and Operation Manual...
  • Page 82 Type show interfaces to check the interface entries. Modify, if needed. Configure and enable Terminal Server Port by typing: configure term-serv ip-address term1 192.160.1.12 configure term-serv description term1 "terminal_device" configure term-serv enable term1 B-12 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 83 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. 076R200-000 SpectraComm IP Router Card B-13 Issue 2 Installation and Operation Manual...
  • Page 84 MANAGED 128.1.1.10 CRAFT DEVICES TERM1 Network SC-IP 192.160.1.12 DEVICE 1 ROUTER TERM2 DEVICE 2 SC-ES TERM3 DEVICE 8 Figure B-2 Example: SC-IP in Back-to-Back Mode (using PPP Protocol) B-14 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...
  • Page 85 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. 076R200-000 SpectraComm IP Router Card B-15 Issue 2 Installation and Operation Manual...
  • Page 86 Type show config to display the current configuration of the SC-IP. • Test your example network by pinging from your PC/workstation at the NOC to equipment at the remote office, and vice-versa. B-16 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

  • Page 87: Cli Reference

    T1 INTERNAL TIMING TIMING TERM8 INBAND MANAGED MANAGEMENT CRAFT DEVICES ADDRESS 172.16.5.10/16 DEVICE 1 DEVICE 2 DEVICE 8 Figure B-3 Example: SC-IPs in LAN-X Mode (“Flat” IP Network) 076R200-000 SpectraComm IP Router Card B-17 Issue 2 Installation and Operation Manual...
  • Page 88 CLI Reference Configuration Tutorials B-18 SpectraComm IP Router Card 076R200-000 Installation and Operation Manual Issue 2...

This manual is also suitable for:

Sc-ip

Table of Contents