Home Screen; Temperature Control; Temperature Lock; Locking Features - HotSpring LimeLight GLEAM Owner's Manual

HOME SCREEN

MEMORY
This feature will recall the last active setting for jets and lights prior to
pressing the All Off button.
IMPORTANT: If the jet pump will not engage, make sure SPA LOCK is
deactivated. SPA LOCK disables the controls on both the Control panels.
ALL OFF
This feature will shut all jets and lights off immediately, while saving the
last active jets and lights settings.
AUDIO
If you purchased music or TV accessories with your spa, this feature will
take you to the Audio menu.
CLEAN
Provided as a convenient timer for water maintenance, this function
activates the jet pump on high for a ten minute period. The jet icon will
flash (on the Home Screen) to indicate the jet pump is engaged and
in the clean cycle. Next you may add properly measured spa water
chemicals into the filter compartment. The jet pump and clean icon will
automatically shut off after ten minutes.
IMPORTANT: Some soft key functions will only be illustrated if the
accessory has been installed.

TEMPERATURE CONTROL

setting programmed at the factory. After the spa has been set up and
used, the last temperature value set by the user will be stored in memory.
If power is disconnected from the spa, it will automatically revert to the last
set temperature when power is reapplied.
To display the set temperature of the spa:
• Press the OPTIONS hard button on the Control panel .
• Press the soft button next to Temperature. The set temperature screen
will be displayed. This screen will automatically revert to the Home
screen after 45 seconds of non-use.
The temperature displayed in the
center of the Home screen is the
actual temperature of the spa water.
If the READY icon is lit and solid
on the screen, then the actual spa
temperature is within 1°C (2°F) of
the set temperature. The corner soft
button functions are as follows:
The set temperature range is from 26°C
to 40°C (80°F to 104°F).
(The water temperature of any spa
may rise or lower slightly depending on
the current use and condition of your
spa and on outside temperatures.)
The set temperature of the spa water
will default to 38°C (100°F) the first
time that power is applied. This is the
To increase the set temperature of the spa water:
• Press the soft button next to ▲.
Each time the button is pressed,
the set temperature display will
increase by 0.5°C. If the button is
held down, the set temperature
display will increase by 0.5°C every
half-second.
To decrease the set temperature of the spa water:
• Press the soft button next to ▼.
Each time the button is pressed, the
set temperature display will decrease
by 0.5°C. If the button is held down,
the set temperature display will
decrease by 0.5°C every half-second.
If the set temperature value does not
change, check to see whether the
TEMP LOCK or SPA LOCK features
are on. When either of these features is activated, the temperature
control is disabled.
The temperature can be displayed in Fahrenheit or Celsius. Press the
soft button next to the °F/°C to choose one or the other.

LOCKING FEATURES

The two locking features, Temperature Lock and Spa Lock, are
activated at the Control panel. Once activated, a lock will remain active
until the specific button combination is pressed to disable the lock.
Even if power to the spa is disconnected even briefly, the lock will
remain activated.

TEMPERATURE LOCK

To activate the Temperature Lock:
• Press the OPTIONS hard button at the Control panel.
• Press the soft button next to Temperature to advance the screen.
• Press the soft button next to Temp Lock Off to change the screen to
Temp Lock On.
IMPORTANT: The Temperature/Spa Lock icon will be displayed on
the Home Screen during a temperature lock condition.
To deactivate the Temperature Lock:
• Press the OPTIONS hard button at the Control panel.
• Press the soft button next to Temp Lock.
• Press the soft button next to Temp Lock On to change the screen to
Temp Lock Off to turn the Temp Lock and icon off.
Page 14
When activated, the Temperature
Lock feature prevents a change
in your desired water temperature
setting. All other functions on the
control panel will operate normally
while the temperature lock is "ON".
This feature prevents others from
changing the owner's desired
settings.
Operating Instructions