Quick Start-Up Instructions; Water Feature - HotSpring LimeLight GLEAM Owner's Manual

Hide thumbs Also See for LimeLight GLEAM:

Owner's manual (56 pages)

Table Of Contents

Table of Contents

MOTO-MASSAGE DX JET (GLEAM ONLY)

The MOTO-MASSAGE DX jet automatically travels up and down in a

sweeping motion, simulating the natural stroking effects of a manual

massage. The intensity of the MOTO-MASSAGE DX jet may be adjusted

by turning the AIR CONTROL lever.

The MOTO-MASSAGE DX jet has been factory adjusted to provide

maximum hydromassage, and to achieve full vertical travel with its

AIR CONTROL lever in the full air volume position. Should the MOTO-

MASSAGE DX jet not achieve full vertical travel and the problem is

not a closed air control valve or clogged filter cartridge, then your HOT

SPRING Service Center should be contacted.

IMPORTANT: A slow or non-moving MOTO-MASSAGE DX jet may

indicate that the filter cartridge pores are obstructed with dirt, body oils,

or calcification. Follow the filter cartridge cleaning procedures in the Spa

Care and Maintenance section of this manual.

DIRECT HYDROMASSAGE JETS

Direct Hydromassage jets are small, producing a precisely narrow

stream of massaging action. They are placed in groups to perform a

soft, soothing massage on your back, neck, and shoulders.

COMBINATION HYDROMASSAGE JETS

These jets deliver a great massage to the feet, back and shoulder areas.

These jets may be adjusted to provide either a stationary, direct stream,

or, by positioning the nozzle to one side, a variety of rotating massage

patterns. Also, the speed of the rotation can be changed by rotating

the jet faceplate from a full stream, to shutting the jet completely off. To

avoid damage to your spa's plumbing and components, do not turn off

more than half of these jets at the same time.

COMBINATION XL HYDROMASSAGE JETS

These large jets may be adjusted to provide either a stationary, direct

stream, or, by positioning the nozzle to one side, a variety of rotating

massage patterns. Also, the speed of the rotation can be changed by

rotating the jet faceplate from a full stream, to shutting the jet completely

off. To avoid damage to your spa's plumbing and components, do not

turn off more than half of these jets at the same time.

COMBINATION JETS MAINTENANCE

If you notice that either the Combination or Combination XL jets spin

slower than when the spa was new, or the jets are sticking, the cause

may be built-up deposits inside the jet bearings. To remove the deposits,

use the following instructions:

1. With the spa off, rotate the combination jet face counter-clockwise

until it stops.

2. Once the face stops rotating, push in and use a little extra force

to rotate the face even more counter-clockwise past the locking

position until it stops. Pull face with the body away from the spa.

3. After flushing the bearing inside the body with water, spin the

rotating eye, it should spin very freely. If it does not, place the

bearing end in a cup of vinegar (the vinegar will soften any

deposits). Leave soaking overnight. The next day, flush with water

and repeat the spin test.

NOTE: If it still doesn't spin freely, a second night of soaking is

required. If the bearing still does not spin, you will need to purchase

a replacement assembly from your HOT SPRING dealer.

4. To replace, position the cutout at the back end of the face body

downward and push the face body back into the spa fitting. Slightly

Getting Started

rotate face body in either direction until you feel the body align with

the fitting, then press firmly on the face body. Once seated, push

and rotate the face clockwise using a little extra force to overcome

the locking position. If the face does not rotate, remove and rotate

face body 180° and repeat this step. Turn the jet pump on, the

combination jet should spin freely.

WATER FEATURE

The GLEAM, PULSE /DL, FLAIR , and GLOW spas come equipped

with a VIDRO water feature. This water feature can be turned on or off

when the two-speed pump is on low speed (tranquil mode) or high speed.

To function correctly, the water feature on/off lever must be placed in the

full on position only.

If the lever is not in the full on position when the pump is on high speed,

it is likely that the water feature will project water substantially farther out

into the spa as the on/off lever is opened. This is not proper operation.

If this occurs, the pump should be turned off, the water feature lever

rotated to the full on position and the pump turned on again.

When not in use turn the on/off lever to the OFF position.

CAUTION: Partial blockage of water flow at entrance of water feature

will cause the water to flow farther into or over the spa.

HOT SPRING LOGO LIGHT

The HOT SPRING logo on the front of the spa illuminates a blue and

green color. These colors indicate the power and ready status of the spa

without having to open the cover to look at the control panel.

Green indicator - water is ready,

within 1°C of set temperature

Blue indicator - Power to spa is on

Green Indicator: The GREEN indicator will light when the spa water

temperature is within 1°C of the set temperature, and will turn off when

the temperature is outside of that range. If you increase or decrease

the temperature setting of the spa, the ready indicator will turn off

until the water temperature reaches the acceptable range for the new

temperature setting. A flashing GREEN indicator means a problem may

exists with the temperature sensor (see Troubleshooting section for

more information).

Blue Indicator: The BLUE indicator is 'on' when the spa is properly

supplied with power. It also provides a diagnostic function–a flashing

BLUE indicator indicates that the heater high limit has tripped, meaning

that either the spa water is above its acceptable temperature range,

or a malfunction has occurred within the spa (such as low circulation

due to clogged filters). An 'off' BLUE indicator means that there is a

problem with the spa control box or the power supplied to the spa (see

Troubleshooting section for more information).