Control Panel; Product View And Features; Wireless Remote Control; Home Screen - HotSpring Grandee NXT Owner's Manual

o I
peratInG nStructIonS
W r
IreleSS emote

WIRELESS REMOTE CONTROL

OPERATING YOUR REMOTE
When activating a function or feature, press
with a light but distinctive touch, the function
or feature will activate as your finger is
removed from the touchscreen.
• The wireless remote control panel should be placed in the docking
tray when not in use.
• Remote control can be placed into docking tray facing either direction.
• Maximum recommended operable distance between remote and dock
is 30 feet. Any obstructions between remote and dock may prevent the
remote from communicating, including through the spa water.
• A convenience tray on the bartop is available as a secondary
placement location while spa is in use. The remote should always
be returned to the docking tray before placing cover over your spa.
VERY IMPORTANT: Your wireless remote is a high tech device
designed for use in your spa, handle accordingly!
• The wireless remote control (IP67 rated) is immersible and
floatable if it is inadvertently dropped into the spa water.
• Never immerse or float remote in the spa for any extended period
of time.
• Do not allow remote to float inside filter area. Extreme turbulence
and impact can render the remote permanently inoperable.
• Dropping the remote on any hard surface may break the screen
rendering the remote permanently inoperable. Physical abuse is
not covered under warranty.
• Remote control will NOT communicate to spa dock if underwater.
• Remote should NOT be docked or stored in ambient temperature
ranges outside of -20º F to +122º F (-30º C to +50º C).
• Radio environments will vary and may occasionally lose
connection between remote and spa or possibly return you
back to the home screen on the remote. This is normal and
regular operation should resume within a few seconds. If loss of
communication persists, consult Troubleshooting section.
• Do not leave remote exposed to direct sunlight for long periods of
time, as solar heat could cause issues with the touch screen.
BATTERY
For best battery performance, place the wireless remote back in the
charging dock when not in use. When not in dock, even in sleep mode,
the battery will consume power.
If battery is depleted, return remote control to the dock for immediate
recharging.
When returned to the dock, all spa functions will be operable but the
remote should remain in the dock until fully charged. Under normal
Operating Instructions
c p
ontrol
The HOT SPRING Wireless Control Panel
features a full color LCD touchscreen to
operate all spa functions and features,
wireless communication to the control
system, and wireless charging via the
bartop dock.
conditions a fully drained battery will take 6-8 hours to recharge.
Contact your authorized HOT SPRING Dealer for replacement of your
anel Lithium Ion battery.
CARE OF YOUR REMOTE:
Use only a clean microfiber cloth and water to clean your LCD screen.
Abrasive cloths, towels, paper towels, and similar items may cause
damage to the remote screen. Don't use around aerosol sprays, solvents,
or abrasives.
WIRELESS REMOTE DISPLAY TIME OUTS:
Full
1 minute
The remote screen will dim after 1 minute and sleep after 5 minutes.
* Remote will only shut down if it is NOT in the docking station for 24
hours. To restart, press the touchscreen and wait for 40 seconds as
remote re-boots and loads screens.

HOME SCREEN

The Home screen is the default screen. The temperature displayed inside
the Home screen is the actual temperature of the spa water.
Home Screen
Functions
NOTE: The wireless remote will revert back to the Home screen after 45
seconds of non use in any other screen.
Home Screen Functions:
Home Screen Features
Page 13
Dim
Sleep
5 minutes
{
Home Screen Features
Press this icon to turn jets on
high and all lights on blue if both
are currently off, or will turn all
Power Button
jets, lights, and music off if those
features are currently on.
Memory Press this icon to access the
Screen Memory screen.
Press this icon to access the Clean
Clean Cycle
Cycle screen. Icon will flash when
Clean Cycle is on.
Settings Press this icon to access the first
Screen Settings screen.
Press this icon to access the Jets
Jets
Control screen.
If installed, press this icon to
ACE
access the ACE Water Care
screen.
*Shut down
24 hours
Status
Indicators
Temperature
Control