Home Screen; Temperature Control; Locking Features - HotSpring Grandee GG Owner's Manual

®
HoT SPRINg logo lIgHT
The Hot Spring logo on the front of the spa illuminates a blue and
green color. These colors indicate the power and ready status of the
spa without having to
open the cover to look
at the control panel. The
green color is equivalent
to the ReAdy Indicator
described in the previous
section, and the blue
color is equivalent to
the PoWeR Indicator
described above.
If blue or green lights are flashing, refer to Troubleshooting section of
owner's Manual.

hOME SCREEN

The temperature displayed in
the center of the Home screen
is the actual temperature of the
spa water. If the ReAdy icon is
lit and solid on the control panel,
then the actual spa temperature
is within 2°F (1°c) of the set
temperature. The corner soft
button functions are as follows:
MeMoRy
This feature will recall the last active setting for jets and lights prior to
pressing the All off button.
ImporTanT: If the jet pump will not engage, make sure SPA lock
is deactivated. SPA lock disables the controls on both the main and
auxiliary control panels.
All oFF
This feature will shut jets and lights off immediately, while saving the
last active jets and lights settings.
AudIo
If you purchased music or TV accessories with your spa, this feature
will take you to the Audio menu.
cleAN
Provided as a convenient timer for water maintenance and activates
the jet pump on high for a ten minute period. The blue jet icon will
flash to indicate the jet pump is engaged and in the clean cycle. Next
you may add properly measured spa water chemicals into the filter
compartment. The jet pump and clean icon will automatically shut off
after ten minutes.
ImporTanT: Some soft key functions will only be illustrated if the
accessory has been installed.

TEMPERATURE CONTROl

The set temperature range is from 80°F to 104°F (26°c to 40°c). (The
water temperature of any spa may rise or lower slightly depending
on the current use and condition of your spa and on outside
temperatures.)
The set temperature of the spa water will automatically be 100°F
operating Instructions
green indicator - water is ready,
within 2°F of set temperature
Blue indicator - Power to spa is on
(38°c) the first time that power is applied. This is the setting
programmed at the factory. After the spa has been set up and used,
the last temperature value set by the user will be stored in memory. If
power is disconnected from the spa, it will automatically revert to the last
set temperature when power is reapplied.
To display the set temperature of the spa:
• Press the oPTIoNS hard button on the Main control panel .
• Press the soft button next to Temperature. The set temperature
screen will be displayed. This screen will automatically revert to Home
screen after 45 seconds of non-use.
To increase the set temperature of the spa water:
• Press the soft button next to ▲. Each time the button is pressed, the
set temperature display will increase by one degree. If the button is
held down, the set temperature
display will increase by one degree
every half-second.
To decrease the set temperature of
the spa water:
• Press the soft button next to ▼.
each time the button is pressed,
the set temperature display
will decrease by one degree. If
the button is held down, the set
temperature display will decrease by one degree every half-second.
If the set temperature value does not change, check to see whether
the TeMP lock and SPA lock features are on. When either of these
features is activated, the temperature control is disabled.
The temperature can be displayed in Fahrenheit or celsius. Press the
soft button next to the °f/°C to choose one or the other.

lOCkINg FEATURES

The two locking features, Temperature lock and Spa lock, are
activated at the main control panel. once activated, a lock will remain
active until the specific button combination is pressed to disable the
lock. even if power to the spa is disconnected even briefly, the lock will
remain activated.
TeMPeRATuRe lock
When activated, the Temperature lock feature prevents a change in
your desired water temperature setting. All other functions on the main
and auxiliary control panels will operate normally while the temperature
lock is "oN". This feature prevents others from changing the owner's
desired settings.
To activate the Temperature lock:
• Press the oPTIoNS hard button at
the Main control panel.
• Press the soft button next to
Temperature to advance the
screen.
• Press the soft button next to Temp
lock off to change the screen to
Temp lock on.
ImporTanT: The red Temperature/Spa lock icon will be lit during a
temperature lock condition.
To deactivate the Temperature lock:
• Press the oPTIoNS hard button at the Main control panel.
• Press the soft button next to Temp lock.
Page 13