Related Manuals for Fisher & Paykel ACTIVESMART RS9120WRJ
Summary of Contents for Fisher & Paykel ACTIVESMART RS9120WRJ
- Page 1 ACTIVESMART™ INTEGRATED REFRIGERATOR FRAMELESS CABINETRY RS9120W Models INSTALLATION GUIDE NZ AU GB IE HK SG IN 846806 A 07.17...
- Page 3 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY NOTE: PRODUCT IS DESIGNED FOR INTEGRATED INSTALLATION ONLY FISHER & PAYKEL: RS9120W(R/L)J AND RS9120WRU models FRAMELESS CABINETRY FRAMED CABINETRY (Frameless: Aligns the refrigerator with the cabinetry) (Framed: Aligns the refrigerator with the frame of the cabinetry) Note: shown with custom panel Note: shown with custom panel and handles attached to fridge...
-
Page 5: Safety And Warnings
SAFETY AND WARNINGS BEFORE INSTALLATION Please follow the installation steps specified to ensure your appliance is installed and WARNING! operates correctly. Electric Shock Hazard Refrigeration alcove preparation Read and follow the safety and warnings outlined in this installation For integrated installation, a finished return of solid material is required across the top and guide before operating this appliance. -
Page 6: Components List
COMPONENTS LIST Door panel fittings – Included with standard refrigerator. #8 x 16 mush washer screw Door hanging bracket Drawer hanging bracket Side bracket Side strap M5 x 10 pan head (35) Phillips screw ((12) for Side trim attachment: Fixed screw method only) #8 x 16 Mush Washer M5 x 10... - Page 7 COMPONENTS LIST Optional accessories – The standard appliance does not include a door panel set. Fisher & Paykel (EZKleen stainless steel) door panel sets are available. For models with a water dispenser, the stainless steel door panel sets are required. For complete integration of Automatic ice models a custom door panel set is required.
- Page 8 COMPONENTS LIST Product hardware – Included with standard refrigerator. Kickstrip filter Top kickstrip grille Bottom kickstrip grille Stainless steel toe kick Cabinet side trim Cabinet top trim* Cabinet top trim joining bracket* Air divider Screw cover Cabinet side trim Fixing bracket Spring Clip (6) Side base bracket Allen key...
-
Page 9: Plan View
PLAN VIEW PLAN VIEW PRODUCT & CAVITY DIM PRODUCT AND CAVITY DIMENSIONS – WITH RD9121WR/RD9121WRU DOOR PANEL SET PRODUCT & CAVITY DIM Flush with front PLAN VIEW of cabinetry PLAN VIEW PLAN VIEW PRODUCT DIMENSIONS Overall height of refrigerator* 2130 Overall width of refrigerator Minimum cabinetry gap clearance from edge of refrigerator Overall depth of refrigerator... - Page 10 PRODUCT AND CAVITY DIMENSIONS – WITH RD9121W DOOR PANEL SET For 90° door swing a hinge limiting pin is supplied with your appliance. This pin fits in the boreholes of the top hinge (refer to Z). WARNING! Before opening the doors, ensure that the refrigerator is ●...
- Page 11 PRODUCT AND CAVITY DIMENSIONS Flush with front of cabinetry PLAN VIEW Note: Shown with custom panel Note: shown with custom and handle attached to fridge panel and handles attached to fridge Note: Shown with custom panel and handle attached to fridge PRODUCT DIMENSIONS Overall height of refrigerator* 2028...
-
Page 12: Product And Cavity Dimensions
PRODUCT AND CAVITY DIMENSIONS For 90° door swing a hinge limiting pin is supplied with your appliance. This pin fits in the boreholes of the top hinge (refer to Z). WARNING! Before opening the doors, ensure that the refrigerator is ●... -
Page 13: Custom Door Panel Dimensions
CUSTOM DOOR PANEL DIMENSIONS Note: Top trim supplied for Note: top trim supplied for 84" installation 2134mm installation PROFILE VIEW CUSTOM PANEL DIMENSIONS Height of top door panel* 1150/1252 Width of top door and bottom drawer panel Height of bottom drawer panel** 722 –... - Page 14 CUSTOM DOOR PANEL DIMENSIONS The drawings below apply to Automatic ice models, (RS9120W(R/L)J). Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on http://thekitchentools.fisherpaykel.com 764mm 558mm 347mm 141mm...
- Page 15 CAVITY PREPARATIONS Left side of cavity 756mm Alternative area above cavity for electrical connections 143mm Floor 51mm 73mm Electrical and water connections must be within this space if located behind the refrigerator Frameless: Finished return Frameless: Finished return top and sides REAR OF CAVITY side and top IMPORTANT!
- Page 16 MAXIMUM DISTANCE OF HOSE AND POWER CORD Power cord (excl. plug) – 700mm LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose – 1350mm Water inlet hose –2120mm Power cord (excl. plug) – 2051mm Power cord (excl. plug) – 2051mm...
- Page 17 2134mm HEIGHT CAVITY – ATTACH ANTI-TIP BRACKET Note: the recommended height of cavity is 2134mm for use with stainless door panels. IMPORTANT! Safety requires refrigerators to be stable when door and/or drawer, are open. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load.
- Page 18 2134mm HEIGHT CAVITY – ATTACH TOP TRIM WARNING! Take care when working with the refrigerator outside of the finished enclosure, as the refrigerator is not secured and has the possibility of tipping forward. Tipping of refrigerator can lead to serious injury or death. Ensure all external packaging material is removed from the refrigerator before installation.
- Page 19 2032mm HEIGHT CAVITY – ATTACH ANTI-TIP BRACKET Note: the overall cavity height of 2032mm is an optional installation for custom panels only. IMPORTANT! Safety requires refrigerators to be stable when door and/or drawer, are open. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 100kg load.
- Page 20 ATTACH SIDE BASE BRACKETS AND DOOR STUDS WARNING! Take care when working with the refrigerator outside of the finished enclosure, as the refrigerator is not secured and has the possibility of tipping forward. Tipping of refrigerator can lead to serious injury or death. Ensure all external packaging material is removed from the refrigerator before installation.
-
Page 21: Connect To Water And Electrical Supply
CONNECT TO WATER AND ELECTRICAL SUPPLY IMPORTANT! The water connection instructions below are intended only for the professional installer. ● ● DO NOT use with water that is microbiologically unsafe or of unknown quality. ● ● WARNING – connect to potable drinkable water supply only. ●... - Page 22 CONNECT TO WATER AND ELECTRICAL SUPPLY At the back of your refrigerator, connect the refrigerator to the electrical supply (230VAC, Thread the free end of the water line hose into the dedicated hole located in the base of the refrigerator, through to the back of the refrigerator (refer to C). 50Hz) with the fitted plug and lead, and turn on.
- Page 23 PRE-ALIGN YOUR PRODUCT INSIDE CABINETRY IMPORTANT! It is important that the doors are in line with the cabinetry front and the refrigerator is centred before following these steps. ● ● It is important that all four corners of the refrigerator are supported firmly onto the floor to eliminate any movement. ●...
- Page 24 INSTALL WATER FILTER CARTRIDGE AND KICKSTRIPS IMPORTANT! The water filter head must be firmly pushed into the refrigerator and secured, incorrect installation can lead to water leaks. ● ● It is not necessary to shut off the water supply when installing the water filter. ●...
- Page 25 ASSEMBLE DOOR PANEL SET The assembly of Fisher & Paykel (EZKleen stainless steel) door panels and custom door panels are outlined below. To protect the finish of the Fisher & Paykel EZKleen stainless steel door panels, leave the protective film on the panels when hanging and remove the film only when the installation is complete. If using custom door panels, ensure they are prepared as per ‘Custom door panel dimensions’...
- Page 26 HANG WATER DISPENSING DOOR PANEL For Fisher & Paykel EZKleen stainless steel door panels only. Remove the external display Connect display harness module from inside the onto the refrigerator door refrigerator. by inserting firmly until you feel it clip securely Thread the display harness (refer to B).
- Page 27 HANG NON-WATER DISPENSING DOOR PANELS For Fisher & Paykel EZKleen stainless steel door panels and custom panels. All door panels have full axis adjustment to ensure they are flush with adjacent walls. To adjust the IMPORTANT! height of each panel turn clockwise to raise stud or counter-clockwise to lower stud (refer to A).
- Page 28 ICE AND WATER INITIATION Now it is time to carry out the ice and water initiation to ensure you are free of leaks before fully installing the product. Ensure the appliance is switched on and the isolation tap has been connected and turned on.
- Page 29 ATTACH FIXING BRACKETS Carefully open the refrigerator door Slide screw cover in between the fixing to attach fixing brackets. Place fixing bracket and the side bracket on the bracket over the side of the appliance and appliance x1. secure mid-way with screws x2 (M5 x 8 countersunk Phillips screws).
- Page 30 ATTACH COVERS If applicable, remove any remaining protective film on your door panels. Open the refrigerator door, firmly push Press the 3M Dual Lock™ tabs together to form pairs (refer to D) and remove the adhesive top cover (refer to A) over the top studs. backing on one side only.
- Page 31 ATTACH TOE KICK The standard appliance includes a stainless steel toe kick (102mm) and the hardware required to mount the toe kick (102mm). Alternatively, the customer can supply their own toe kick (102 – 152mm) for complete integration of the refrigerator. Installing toe kick Place toe kick in front of the brackets and gently push towards the refrigerator until flush Unscrew the toe kick bracket screws mid-way, and bring forward (refer to A and B).
- Page 32 MATCHING HOLES ON PLASTIC PARTS ATTACH BOTTOM KICKSTRIP For custom toe tick greater than 102mm For toe kick installation at 102mm Measure the required height for the bottom grille. On a board, carefully score/cut With the grille tabs facing upwards, align the grille clips to the bottom of the plinth’s slots, DETAIL A the un-required vanes from the bottom of the kickstrip grille and discard (refer to A).
- Page 33 TWO METHODS ARE AVAILABLE FOR ATTACHING SIDE TRIM BRACKETS: (A) FLEXIBLE SPRING CLIP METHOD – RECOMMENDED METHOD (B) FIXED SCREW METHOD – METHOD TO USE IF CABINET IS NOT TO SPECIFICATION (Attempt method A. If method A results in poor fitment of side trims due to cabinetry that is uneven or out of specification, use method B). ATTACH SIDE TRIM BRACKETS –...
- Page 34 ATTACH SIDE TRIM BRACKETS – (A) FLEXIBLE SPRING CLIP METHOD Spring clip Side trim lip Top view of spring clip correctly inserted between side trim and side trim bracket Insert the spring clip into the gap between the side trim and side trim bracket, Open refrigerator door.
- Page 35 ATTACH SIDE TRIM BRACKETS – (B) FIXED SCREW METHOD If method A has resulted in poor fitment of side trims due to cabinet being out of spec, use method B. 50mm IMPORTANT! Before installing your appliance, ensure the dimensions of the finished enclosure are 1753mm correct for your appliance following the ‘Product and cavity dimensions’...
- Page 36 ATTACH SIDE TRIM BRACKETS – (B) FIXED SCREW METHOD Place the side trim against the alcove side wall with the shorter lip facing the bottom (refer to D). Ensure the side trim is positioned as high as it will go. ●...
- Page 37 ADJUST HINGE TENSIONING SCREWS Hinge tensioning screws can be tightened if increased door closing force is required. To tighten the screw, hold the door open at 90 degrees, and rotate the screw clockwise until it has moved sideways from position 0 to position 1, and then continue tightening until the screw has fully bottomed out.
-
Page 38: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door/drawer can open and close freely with no resistance from surrounding cabinetry. - Page 40 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2017. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.