Related Manuals for Fisher & Paykel ACTIVESMART RS9120WRJ1
Summary of Contents for Fisher & Paykel ACTIVESMART RS9120WRJ1
- Page 1 ACTIVESMART™ INTEGRATED REFRIGERATOR FREEZER RS9120W models INSTALLATION GUIDE NZ AU GB IE HK SG IN...
-
Page 3: Table Of Contents
CONTENTS SAFETY AND WARNINGS COMPONENTS TOOLS APPLIANCE AND CAVITY DIMENSIONS CABINETRY OPTIONS STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS CUSTOM DOOR PANEL INSTALLATION DIMENSIONS CUSTOM DOOR PANEL INSTALLATION TEMPLATE DOOR CLEARANCE ELECTRICAL AND PLUMBING BEFORE INSTALLATION CAVITY PREPARATION WATER AND POWER SUPPLY CONNECTION... -
Page 5: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT! WARNING! It is very important for the installer to follow the instructions in this installation guide to ensure proper installation and operation of the appliance. Ensure that you read the Electric Shock Hazard installation guide thoroughly and understand all information. Read and follow the safety and warnings The water connection to your Ice and water appliance must be installed by an authorized plumber or Fisher &... -
Page 6: Components
COMPONENTS Internal box (Installation kit) Located inside the appliance Anti-tip bracket Door panel Door / d rawer trim Cabinet side trim assembly kit attachment kit install kit install kit Anti-tip bracket Side bracket Dual adhesive tabs Side trim bracket (10) (12) Masonry plug Side strap Side cover Spring clip... - Page 7 COMPONENTS External box Ice and Water display Located at back panel of appliance (Ice and Water models only) Located inside the appliance Door side trim Drawer side trim Cabinet side trim Double-sided door panel template External display module Top trim Drawer top trim Top grille Toe kick...
-
Page 8: Tools
COMPONENTS TOOLS Door panel set Required tools Not supplied and must be purchased separately Not included with appliance Stainless steel (Fisher & Paykel) door panel set: Custom door panel set: Includes 1x single door panel and 1x drawer panel. Supplied by customer to match their cabinetry. Applicable for Non-water dispensing models only. -
Page 9: Appliance And Cavity Dimensions
APPLIANCE AND CAVITY DIMENSIONS IMPORTANT! For ease of installation, ensure cavity width is consistent top to bottom and height is consistent left to right. PLAN VIEW Flush install Flush install Frameless: Finished return top and sides Framed: Finished return top and sides CAVITY DIMENSIONS Overall height of cavity 2032... -
Page 10: Cabinetry Options
CABINETRY OPTIONS FRAMELESS CABINETRY FRAMED CABINETRY (Aligns the appliance with the cabinetry) (Aligns the appliance with the frame of the cabinetry) Note: Drawings are only for reference and not the actual cavity width of the cabinetry. -
Page 11: Stainless Steel Door Panel And Toe Kick Dimensions
STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS Available on Available on Ice and Water Ice and Water models only models only DOOR PANEL SET DOOR PANEL SET RD9120W / R D9120WRU RD9121W / R D9121WRU RD9120W / RD9121W ... -
Page 12: Custom Door Panel And Toe Kick Dimensions
CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS IMPORTANT! Custom door / d rawer panels are Note: Top trim supplied applicable for Non-water dispensing Note: Top trim supplied for for 2134mm installation 84" installation models only. PROFILE VIEW CUSTOM PANEL DIMENSIONS Height of top door panel 1150 – 1252 Width of top door and bottom drawer panel... -
Page 13: Custom Door Panel Installation Dimensions
CUSTOM DOOR PANEL INSTALLATION DIMENSIONS The drawings below apply to Non-water dispensing models only (RS9120WRJ and RS9120WLJ). Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com. 764mm 558mm 347mm... -
Page 14: Custom Door Panel Installation Template
CUSTOM DOOR PANEL INSTALLATION TEMPLATE This template is a single double-sided sheet used as DRAWER PANEL TOP EDGE a guide to drill screw holes for installing your Custom door and drawer panels. The actual template is included with this installation guide. DOOR PANEL LEFT SIDE DOOR PANEL RIGHT SIDE HANGING BRACKET HOLES... -
Page 15: Door Clearance
DOOR CLEARANCE Insert hinge limiting pin WARNING! Before opening the doors, ensure that the appliance is stable. Follow these steps to avoid risks that can cause serious injury or death. 115° DOOR OPENING 90° DOOR OPENING (FULL INTERNAL ACCESS) For 90° door swing, a hinge limiting pin is supplied with your appliance. -
Page 16: Electrical And Plumbing
ELECTRICAL AND PLUMBING IMPORTANT! WARNING! Electrical connection should be located in an adjacent cabinet to either side Electrical shock hazard. Assume all parts are live. of the appliance or above the appliance cavity. Disconnect supply before servicing and installation. We recommend to use an isolating switch that is easily accessible to the user after the appliance is installed. - Page 17 ELECTRICAL AND PLUMBING Maximum distance of hose and power cord Power cord (excluding plug) — 800mm LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose — 1350mm Water inlet hose — 2120mm Power cord (excl. plug) — 2051mm Power cord (excl. plug) — 2051mm ELECTRICAL SPECIFICATIONS PLUMBING SPECIFICATIONS Supply 230V, 50 Hz Supply 13mm or 19mm...
- Page 18 BEFORE INSTALLATION IMPORTANT! Be careful when unpacking to prevent damage to the surface of your appliance. Ensure that the feet of the appliance are retracted. Ensure that the appliance is stable to prevent from tipping over when unpacking. If the appliance is damaged, contact your Fisher & Paykel dealer. Do not open the doors to prevent the appliance from tipping over.
-
Page 19: Before Installation
BEFORE INSTALLATION IMPORTANT! Ensure your appliance is not exposed to any heat generating appliance eg cooktop, supported service technician to avoid faulty electrical connection and water leaks. oven or dishwasher. All connections for water, electrical power and grounding must comply with local codes The appliance has front and rear rollers for moving the appliance forward and backward. -
Page 20: Cavity Preparation
CAVITY PREPARATION Internal box IMPORTANT! WARNING! The anti-tip bracket and fittings supplied must be fitted to the wall Read the following before fastening with masonry plugs and/or screws: Anti tip of the finished enclosure to withstand 100kg load. Ensure the screws avoid electrical, gas and water conduits. bracket kit Ensure that anti-tip bracket is installed correctly to prevent the Ensure lightweight masonry material such as cinder block... -
Page 21: Water And Power Supply Connection
WATER AND POWER SUPPLY CONNECTION Water fittings kit IMPORTANT! Ensure that the water connection is performed by a professional installer. Ensure there is enough tubing for the water connection and to pull The product comes with a pre-connected plastic water tubing. the appliance out for service, if required. -
Page 22: Top Trim Installation
TOP TRIM INSTALLATION Internal box WARNING! Be careful when working with the appliance outside of the finished enclosure. Top trim Ensure that the appliance is secured to prevent tipping forward. Tipping of appliance can lead to serious injury or death. install kit Install top trim — for 2134mm cavity only Insert M5 nuts (A) into... -
Page 23: Side Bracket Installation
SIDE BRACKET INSTALLATION Internal box IMPORTANT! Ensure all external packaging materials are removed from the appliance before installation. Side bracket Ensure the door of the appliance is closed during installation. install kit Attach side base brackets Fix the side base brackets to the base left and right sides of the appliance Side base brackets (R/L) with M5x8 countersunk cross-head screws (A). -
Page 24: Positioning Into Cabinetry
POSITIONING INTO CABINETRY IMPORTANT! Ensure the hose is not run over by the appliance when pushing into the cabinetry to prevent damage and possible water leaks. Position the appliance into the cabinetry Coil the excess water hose and power cord flat behind the appliance (A). Push the appliance into the cabinetry until the anti-tip bracket overlaps the rear top edge of the appliance (B), and the doors are in line with the cabinet frame. -
Page 25: Aligning Inside Cabinetry
ALIGNING INSIDE CABINETRY Tools IMPORTANT! Ensure all four corners of the appliance is supported firmly onto the floor If using a Powered driver, use low torque setting to avoid damaging to eliminate any movement. the height adjustment system. DO NOT install the appliance on a soft, uneven, or unlevelled floor Ensure that the top, bottom and sidge gap differences are not greater to avoid twisting the appliance and poor door sealing. - Page 26 DOOR PANEL INSTALLATION — STAINLESS STEEL Internal box IMPORTANT! Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. Door panel Ensure to protect the finish of the Stainless steel door panels. attachment kit For non-water dispensing door panels: Leave the protective film on the panels when hanging and remove the film only when installation is complete. Remove hanging brackets Attach the door and drawer handles (C) Side bracket...
- Page 27 DOOR PANEL INSTALLATION — STAINLESS STEEL Ice and Water display IMPORTANT! (Ice and Water Failure to follow these steps can lead to difficulties in door panel adjustment and cosmetic cap fitment. models only) For water dispensing door panels: Remove the protective film from the appliance doors before hanging door panels. Connect the external display module (for Ice and Water models only) External display module Remove the external display module...
- Page 28 DOOR PANEL INSTALLATION — STAINLESS STEEL Tools Attach the door panels Open the door and loosen the M5x10 cross-head screws (do not remove) at the sides of the doors (A). Hang the door panel by inserting the M8 studs through the holes of the hanging bracket (B). FPA spanner Slide the forks of the side brackets onto the screws of the door (C).
- Page 29 DOOR PANEL INSTALLATION — STAINLESS STEEL IMPORTANT! Door panel Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. attachment Adjust the door panels Place a ruler on the front of the appliance to check 8x16 mush washer screw flushness top and bottom, left and right.
- Page 30 DOOR PANEL INSTALLATION — CUSTOM External box IMPORTANT! The template should be placed on the back side of the back side of front side of door panel. door panel door panel Door panel double-sided template (1) Using the installation template To mark the drill locations of middle screw holes, align the (for top door panel) screw holes of door hanging bracket with right and left Tools...
- Page 31 DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! back side of front side of The template should be placed on the back side of the door drawer panel door panel panel. Using the installation template To mark the drill locations of middle screw holes, align the (for drawer panel) screw holes of drawer hanging bracket with right and left drilled screw holes.
- Page 32 DOOR PANEL INSTALLATION — CUSTOM Internal box Attach the door and drawer handles (C) Remove hanging brackets Remove the M8 washers and M8 nuts from the M8 Align the handle holes with the door Door panel studs at the top the door (A) using the hex key and panel holes and secure the handle with attachment kit M5x25 pan head socket screws (4 for each...
- Page 33 DOOR PANEL INSTALLATION — CUSTOM Tools Attach the door panels Open the door and loosen the M5x10 cross-head screw (do not remove) at the sides of the doors (A). Hang the door panel by inserting the M8 studs through the holes of the hanging bracket (B). FPA spanner Slide the forks of the side brackets onto the screws of the door (C).
- Page 34 DOOR PANEL INSTALLATION — CUSTOM IMPORTANT! Door panel Follow these steps to avoid difficulties in door panel adjustment and cosmetic cap fitment. attachment Adjust the door panels Place a ruler on the front of the appliance to check flushness top 8x16 mush washer screw and bottom, left and right.
-
Page 35: G Fixing Bracket
FIXING TO CABINETRY Internal box Attach fixing brackets Fixing bracket install kit Fixing bracket M5x8 countersunk cross-head screw (8) Screw cover Open the top door carefully. Slide the screw cover between the fixing bracket Place the fixing brackets on the top and side base and the side bracket on the appliance (C). - Page 36 WATER FILTER INSTALLATION Miscellaneous IMPORTANT! items pack The water filter head must be firmly pushed into the appliance and secured. incorrect installation can lead to water leaks. Water filter Filter handle Filter cartridge tool Front view Filter in locked position Install the water filter Remove the plastic wrapping of the new filter.
- Page 37 TOE KICK INSTALLATION External box Install the toe kick filter and grille Fit the filter onto the rails and push until it clips securely (A). Align the top grille clips to the top plinth slots. Ensure the top grille is in the correct orientation (B). Push the grille firmly onto the appliance until the clips engage (C).
- Page 38 TOE KICK INSTALLATION IMPORTANT! Internal box The standard appliance includes a stainless steel toe kick 102mm and the components required to mount the toe kick. Door / d rawer Alternatively, the customer can supply their own custom toe kick 102 – 152mm for complete integration of the appliance. trim install kit For standard toe kick —...
- Page 39 DOOR AND DRAWER TRIMS INSTALLATION Internal box Attach the covers Attach the drawer top and side trims Open the top door. Attach the top cover Peel off two dual adhesive tabs and press them Door / d rawer (A) firmly over the top stud on the handle together to form a pair (E).
-
Page 40: Side Trim Bracket
TWO METHODS ARE AVAILABLE FOR ATTACHING CABINET SIDE TRIMS: [A] FLEXIBLE SPRING CLIP METHOD — RECOMMENDED METHOD [B] FIXED SCREW METHOD — METHOD TO USE IF CABINET IS NOT TO SPECIFICATION (Attempt method [A]. If method [A] results in poor fitment of side trims due to cabinetry that is uneven or out of specification, use method [B]). CABINET TRIMS INSTALLATION — [A] FLEXIBLE SPRING CLIP METHOD Internal box Break off the datum lip to each side trim... - Page 41 CABINET TRIMS INSTALLATION — [A] FLEXIBLE SPRING CLIP METHOD Insert the spring clip into the gap between the side trim and Open the French doors. Place the assembled side trim with brackets and spring side trim bracket, orientation as shown in figures (D) and (E). clips against the alcove side wall with the shorter lip facing the bottom (F).
-
Page 42: 8X16 Mush Washer Screw
CABINET TRIMS INSTALLATION — [B] FIXED SCREW METHOD Internal box Break off the datum lip to each side trim bracket and discard. Position three side trim brackets on one side trim. Refer to (B) for bracket locations. Repeat for all side trim brackets. Open the French doors. Measure 50mm from the front of cabinet Cabinet side (from behind the doors), to the front of the alcove and accurately trim install kit... - Page 43 CABINET TRIMS INSTALLATION — [B] FIXED SCREW METHOD Place the side trim against the alcove side wall with the shorter lip facing the bottom (E). – Ensure the side trim is positioned as high as it will go. Side trim Side trim bracket Top view of side trim engaged correctly in side trim bracket...
- Page 44 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Ensure all internal and external packaging is removed from the appliance before use. Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings.
- Page 48 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The appliance specifications in this document apply to the specific appliances and models described at the date of issue. Under our policy of continuous appliance improvement, these specifications may change at any time.