Fisher & Paykel ACTIVESMART RS90A Installation Manual
Integrated slide-in refrigerator
Hide thumbs
Also See for ACTIVESMART RS90A:
- User manual (48 pages) ,
- Installation instructions manual (25 pages) ,
- Installation manual (44 pages)
Related Manuals for Fisher & Paykel ACTIVESMART RS90A
Summary of Contents for Fisher & Paykel ACTIVESMART RS90A
- Page 1 ACTIVESMART™ INTEGRATED SLIDE-IN REFRIGERATOR RS90A & RS90AU models INSTALLATION GUIDE NZ AU GB IE HK SG IN 844219A 07.18...
-
Page 3: Table Of Contents
CONTENTS FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY 1 SAFETY AND WARNINGS 2 COMPONENTS LIST 3 PRODUCT AND CAVITY DIMENSIONS 4 DOOR PANEL DIMENSIONS 5 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS 6 DOOR OPENING ROTATION 7 ELECTRICAL AND PLUMBING 8 BEFORE INSTALLATION 9 ATTACH ANTI-TIP BRACKET !0 REMOVE HINGE END CAPS !1 CONNECT TO WATER AND ELECTRICAL SUPPLY !2 ALIGN YOUR PRODUCT INSIDE THE CABINETRY... -
Page 5: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT! WARNING! The water connection to your Ice & water refrigerator must be installed by an ● ● authorised plumber or Fisher & Paykel trained and supported service technician Electric Shock Hazard and comply with all state and local laws. Read and follow the safety and warnings outlined in this installation Installation and use MUST comply with all state and local plumbing codes. -
Page 6: Components List
COMPONENTS LIST MI (miscellaneous items) pack — included with the refrigerator Product accessories — included with the refrigerator ACTIVESMART™ ACTIVESMART™ INTEGRATED INTEGRATED REFRIGERATOR SLIDE-IN REFRIGERATOR RS90A, RS9120W, RS90A & RS90AU models RS36A72, RS36A80 & RS36W80 models SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA Toe kick filter (1x) Toe kick grille (1x) - Page 7 COMPONENTS LIST Door panel set Door panel fittings — included with the refrigerator French door hanging Drawer hanging Side screw (10x) Screw washer Custom door panel set Fisher & Paykel bracket (2x) bracket (1x) 4x14 (34x) is only applicable for (Stainless steel) non-Water dispensing door panel set is not included with...
-
Page 8: Product And Cavity Dimensions
PRODUCT AND CAVITY DIMENSIONS IMPORTANT! For ease of installation, ensure cavity width is consistent top to bottom and height is consistent left to right. h custom to fridge Flush with front of cabinetry TOP VIEW Note: shown with Standard Fisher & Paykel door panels (Stainless steel) attached to fridge FRONT VIEW PROFILE VIEW... -
Page 9: Door Panel Dimensions
DOOR PANEL DIMENSIONS FRONT VIEW PROFILE VIEW STAINLESS STEEL/CUSTOM DOOR PANEL DIMENSIONS Height of each top door panel 1096 Width of each top door panel Gap between top door panels Height of bottom drawer panel Height from bottom of product to top of bottom drawer panel Width of bottom drawer panel Gap between top door panels and bottom drawer panel Depth of each door panel (without handle) -
Page 10: Custom Door Panel Installation Dimensions
CUSTOM DOOR PANEL INSTALLATION DIMENSIONS CUSTOM PANEL PREPARATION The following drawings apply to non-Ice & Water models only. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com CUSTOM PANEL PREPARATION Handle details 392.3mm Top panel – Ensure handle is mounted 65mm from inner R1.25 REF edge of panel to the centre... -
Page 11: Door Opening Rotation
DOOR OPENING ROTATION Wall Wall 115° DOOR OPENING 90° DOOR OPENING (FULL ROTATION) 115° DOOR OPENING 115° DOOR OPENING 90° DOOR OPENING 90° DOOR OPENING [FULL ROTATION] [FULL ROTATION] For 90° door swing a hinge limiting pin is supplied with RS90A/RS90AU your refrigerator. -
Page 12: Electrical And Plumbing
ELECTRICAL AND PLUMBING WARNING! Electrical shock hazard. Assume all parts are live. Disconnect supply before servicing and installation. Left side of cavity Alternative area above cavity for connections 100mm Optional electrical and 130mm water connection location* 100mm Floor 72mm 145mm 355mm REAR VIEW OF CAVITY REAR VIEW OF CAVITY... - Page 13 ELECTRICAL AND PLUMBING Maximum distance of hose and power cord Water inlet hose* – 2250mm Power cord (excl.plug) – 800mm LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose* – 3180mm Water inlet hose* – 3930mm Power cord (excl.plug) – 2050mm Power cord (excl.plug) –...
-
Page 14: Before Installation
BEFORE INSTALLATION IMPORTANT! Ensure your refrigerator is not exposed to any heat generating appliance eg cooktop, oven or dishwasher. ● ● The refrigerator has front and rear rollers for moving the refrigerator forward and backward. Do not move the refrigerator sideways to avoid damaging the rollers or floor covering/surface. ●... -
Page 15: Attach Anti-Tip Bracket
ATTACH ANTI-TIP BRACKET IMPORTANT! WARNING! Ensure the refrigerator door is closed when rolling into cabinetry. Read the following reminders before fastening with masonry plugs and/or screws: ● ● DO NOT attempt to open the door until refrigerator is fully installed. Ensure the screws avoid electrical, gas and water conduits. -
Page 16: Remove Hinge End Caps
REMOVE HINGE END CAPS WARNING! Take care when working with the refrigerator outside of the finished enclosure, ● ● as the refrigerator is not secured and has the possibility of tipping forward. Tipping of refrigerator can lead to serious injury or death. ●... - Page 17 CONNECT TO WATER AND POWER SUPPLY IMPORTANT! The water connection instructions below are intended Fisher & Paykel water fittings are available (part number: 841301) and comply with local regulations. ● ● ● ● only for the professional installer. Ensure water tubing is routed away from any sharp objects, sharp corners, and not in a location where it can be kinked or ●...
- Page 18 ALIGN YOUR PRODUCT INSIDE THE CABINETRY IMPORTANT! Your product is fitted with front and rear rollers designed for moving the product in the forwards and backwards direction. ● ● Avoid moving the product in a sideways direction as this may damage the rollers or the floor covering/surface. ●...
- Page 19 ALIGN YOUR PRODUCT INSIDE THE CABINETRY IMPORTANT! Add ruler to show ushness x 4? It is important that all four corners of the product is supported firmly onto the floor to eliminate any movement. ● ● Installing the refrigerator on a soft or uneven/unlevelled floor may result in twisting of the product and poor door sealing. ●...
- Page 20 ASSEMBLE THE DOOR AND DRAWER PANELS IMPORTANT! Ensure door panel dimensions are correct for your refrigerator. ● ● The assembly of standard Fisher & Paykel kits (Stainless steel door panels) and custom door panels are outlined below. For standard Fisher & Paykel kits, only ●...
- Page 21 HANG THE DOOR PANELS For non-Ice & Water models only Secure top studs into the Secure side screws mid-way into Hang door panel onto the top refrigerator doors, ensure the the refrigerator doors x4 for each studs and align the side bracket open end faces the top.
- Page 22 HANG THE DOOR PANELS For Ice & Water models only Remove the external display Angle top display tabs into the Connect display harness onto the refrigerator door module from inside the product. door panel. Ensure the harness by inserting firmly until you feel it clip securely (B). is free of pinching.
- Page 23 FIX THE BRACKETS AND RE-INSTALL THE END HINGE CAPS Secure fixing bracket to the ceiling of the enclosure Left hinge end cap Right hinge end cap with wood screw (1x) (A). Align hinge cap to the product. Align hinge cap to product. Press and firmly slide the cap to the right (B).
- Page 24 INSTALL WATER FILTER AND TOE KICK GRILLE IMPORTANT! The water filter head must be firmly pushed into the product and secured. incorrect installation can lead to water leaks. ● ● Installing the water filter Installing the toe kick filter and grille Pull the freezer drawer out slightly and insert the filter into the casing at the bottom Remove filter from inside the product.
- Page 25 ATTACH COVERS AND DOOR/DRAWER TRIMS If applicable, remove any remaining protective film on your door panels. Open the refrigerator French doors, firmly push top cover (A) Press the dual adhesive tabs together to form pairs (E) and remove over the top studs. the adhesive backing on one side only.
- Page 26 ATTACH CABINET SIDE TRIMS IMPORTANT! Before installing your refrigerator, ensure the dimensions of the finished enclosure are correct for your refrigerator following the ‘Product and cavity dimensions’ sections. Side trim bracket Side trim Discard Top view of side trim engaged correctly in side trim bracket IMPORTANT! Each bracket has two engagement points for the side trim to locate.
- Page 27 ATTACH CABINET SIDE TRIMS Spring clip Side trim lip Top view of spring clip correctly inserted between side trim and side trim bracket IMPORTANT! IMPORTANT! Ensure spring clip is correctly oriented with the open loop facing the side trim lip. Ensure the side trim is positioned as high as it will go.
- Page 28 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the refrigerator is level. Ensure the refrigerator is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the doors/drawer can open and close freely with no resistance from surrounding cabinetry.