Related Manuals for CAME KR302
Summary of Contents for CAME KR302
- Page 1 GEARMOTOR FOR SWING GATES FA 00290 - EN INSTALLATION MANUAL KR300 - KR302 - KR310 - KR312 KR510 - KR512 English...
- Page 2 THE PHOTOCELLS ARE WORKING PROPERLY HIS IS THE ONLY WHICH IT WAS EXPLICITLY DESIGNED NY OTHER USE IS DANGEROUS MAINTENANCE OPERATION TO DO WITH THE POWER ON ONSTANTLY CLEAN THE CAME S. LIABLE DAMAGE CAUSED • K PHOTOCELLS GLASS COVERS USING A SLIGHTLY WATER...
-
Page 3: Intended Use
This gearmotor is designed to power and operate swing gates in private homes and apartment blocks. Any installation and/or use other than that specifi ed in this manual is forbidden. Limits to use KR510 - KR512 KR300 - KR302 - KR310 - KR312 1200 1000 5,25 Gate-leaf length (m) We suggest you always fi... - Page 4 Dimensions (mm) 956 * - 1356 ** 304 * - 504 ** * KR300 - KR302 - KR310 - KR312 ** KR510 - KR512 Description of parts 1. Gearmotor 2. Cover 3. Post braces with bushing, fastening screw and self-locking nut 4.
- Page 5 GENERAL INSTALLATION INDICATIONS Only skilled, qualified staff must install this product. Preliminary checks Before beginning, do the following: • check that the gate structure is sturdy enough, the hinges work efficiently and that there is no friction between the fixed and moving parts; •...
-
Page 6: Installation
Establish the point the gate and post braces will be fitted, while respecting the quotas shown on the table. Post bracket Gate bracket Application dimension (mm) KR300 - KR302 - KR310 - KR312 Leaf opening arc (°) C MAX 90°... - Page 7 Assemble and weld the two parts of the post brace. Fasten the brace to the established point, using suitable plugs and screws. If the post is metallic, weld the brace. Weld the gate brace to the leaf following the measurements shown on the table. ...
-
Page 8: Connecting To The Control Panel
Fastening the gearmotor Lubricate the bushing and fit into one of the post brace holes (the holes on the brace are for varying the gate's opening angle. Fasten the joint to the post brace using the bolt and nut. Open the leaf, fit the pinion into the gate brace and fasten it using the supplied washer and nut. Connecting to the control panel Warning! Before working on the control panel, cut off the main current supply and, if present, remove any batteries. -
Page 9: Establishing The Limit-Switch Points
Establishing the limit-switch points Before establishing the limit-switch points, you must remove the cover by loosening the fastening screw. The closing microswitches are positioned at the far ends of their travel range. For closing Release the gearmotor. Push the leaf to its closing strike position. Send a (2-4) closing command and turn the threaded rod counter clock-wise until the closing microswitch activates to stop the gearmotor. - Page 10 Measure quotas A and B (while respecting the quotas shown on the table) to establish the point where the post brace joined with non-supplied supplementary brace will be fastened. Application dimension (mm) KR300 - KR302 - KR310 Leaf opening arc (°) 90°...
- Page 11 Assemble and weld the supplementary brace to the post brace. Fasten the supplementary brace to the post. Open the gate to 90°, weld or fasten the gate brace using suitable bolts (while respecting quota E as shown in the table). Fasten the gearmotor to the braces by using the supplied nuts and bolts.
- Page 12 Connecting to the control panel Warning! Before working on the control panel, cut off the main current supply and, if present, remove any batteries. 230 V AC gearmotor fi tted on the left (inside 230 V AC gearmotor fi tted on the right (inside view), with delayed closing.
-
Page 13: Final Operations
FINAL OPERATIONS Proceed with the fi nal steps, only once you have completed all connections and made the gate operational. Fit the cover and fasten the screw. RELEASING THE GEARMOTOR This procedure must be done with the main power cut off . The gearmotor's manual release may cause unwanted movement of the gate, if the latter has any mechanical issues or if it is not balanced. -
Page 14: Troubleshooting
TROUBLESHOOTING TROUBLES POSSIBLE CAUSES FIXES It neither opens • Power supply missing • Check main power supply nor closes • The gearmotor is stuck • Lock the gearmotor • The transmitter's battery is run down • Replace the batteries • The transmitter is broken •... -
Page 15: Dismantling And Disposal
__________________________________________________________________________________________ DISMANTLING AND DISPOSAL ☞ CAME S.p.A. applies a certified Environmental Management System at its premises, which is compliant with the UNI EN ISO 14001 standard to ensure the environment is safeguarded. Please continue safeguarding the environment. At CAME we consider it one of the fundamentals of our operating and market strategies. Simply... - Page 16 Came S.p.A. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c 31030 Dosson di Casier Dosson di Casier 33079 Sesto al Reghena Sesto al Reghena Treviso Treviso - Italy Pordenone Pordenone - Italy (+39) 0422 4940 (+39) 0434 698111...