Table of Contents
Advertisement
EventLogFilter
Specifies what events to include in the event log display. Type
"get EventLogFilter" for a list of valid subsystems. Specify a
subsystem with "none" to disable event display for that
subsystem. Levels are "info", "warn" and "crit". Specify "info" to
display all levels, "warn" to display warnings and critical events,
"crit" to display only critical events. Events are classified
"factory" or "user" (factory events provide detailed information
for factory debug, and they are marked with a dash.) Specify
"factory" to display all events, or specify "user" to display only
user events.
Default: [ECC | ENET | GEN | HTTP | NVRAM | FC | SAS
| BACKDEV] Info Factory
set EventLogFilter [subsys | all] [[info | warn | crit] [factory
| user]] | none]
get EventLogFilter
Exit
Exit terminates the current CLI session over Telnet. This
command has no effect if used during a serial RS-232 session.
Exit
FCConnMode
(all but SC 8250)
FCConnMode specifies the connection mode used when
communicating across a Fibre Channel network. The system
will connect to an arbitrated loop (FC_AL) if 'loop' is selected.
The system will connect in point-to-point mode if 'ptp' is
selected. The options of 'loop-ptp' (AL Preferred) and 'ptp-loop'
(PTP Preferred) allow auto-negotiation while indicating a
preference.
Default: loop
set FCConnMode [fp | all] [loop | ptp | loop-ptp | ptp-loop]
get FCConnMode [fp | all]
FCDataRate
(all but SC 8250)
FCDataRate specifies the Fibre Channel data rate at which
operation will occur. Choices are 2Gb/s, 4Gb/s, 8Gb/s or Auto-
negotiated. Note - the FCDataRate displayed in the "info" output
will toggle between 1Gb (5550 only), 2Gb, 4Gb, and 8Gb (8550
only) on 8Gbit-capable hardware if no connection has been
established.
set FCDataRate [fp | all] [2Gb | 4Gb | 8Gb | auto]
get FCDataRate [fp | all]
FCHard
(all but SC 8250)
FCHard enables and disables Fibre Channel hard address
assignment. When FCHard is enabled, the internal hard
address will be used as the loop address on the Fibre Channel
loop. Under soft addressing, the loop address is assigned
during loop initialization.
set FCHard [enabled | disabled]
get FCHard
xvi
ATTO Technology Inc. FastStream SC Installation and Operation Manual
FCHardAddress
(all but SC 8250)
FCHardAddress specifies the value used as the FC-AL hard
address. This value represents the address that will be used if
hard addressing is enabled. The range of valid Fibre Channel
Hard Address values is 0 through 125.
set FCHardAddress [fp | all] [address]
get FCHardAddress [fp | all]
FCMultiNode
(all but SC 8250)
FCMultiNode determines the reported identity of Fibre Channel
ports. When enabled, each port reports a separate unique Node
Name and logical units may be mapped to either port. When
disabled, each port reports the same Node Name and each
logical unit mapping is applied to all ports.
set FCMultiNode [enabled | disabled]
get FCMultiNode
FCPortErrors
(all but SC 8250)
FCPortErrors displays the number of Fibre Channel errors that
have occurred since the last reboot/power-on or
ResetFcPortErrors.
get FCPortErrors [fp | all]
FCPortList
(all but SC 8250)
FCPortList displays a list of available Fibre Channel ports and
their current status. Valid status values are: Up, Down, Failed,
Reserved, and Disabled.
FCPortList
FCWWName
(all but SC 8250)
FCWWName reports the World Wide Node Name of the Fibre
Channel interface referenced. Each Fibre Channel port has an
individual and unique 8-byte Node Name if the FCMultiNode
setting is enabled.
get FCWWName [fp | all]
FirmwareRestart
FirmwareRestart resets and reinitializes the firmware. Use the
'forced' option to override any CLI reservations held by other
sessions.
FirmwareRestart <forced>
FlashImages
FlashImages displays the metadata for software images
currently stored in the Flash device. The optional parameter
"validate" also validates the CRC of the flash images. Note that
the CRC validation causes a multi-second delay.
FlashImages <validate>
Advertisement
Table of Contents
