Oliver 732-N User's Operating And Instruction Manual
  1. Manuals
  2. Brands
  3. Oliver Manuals
  4. Kitchen Appliances
  5. 732-N
  6. User's operating and instruction manual

Oliver 732-N User's Operating And Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Grand Rapids, Michigan, U.S.A. 49504-5298
USER'S OPERATING AND INSTRUCTION MANUAL
MODEL 732-N
BREAD SLICER
0732S20000-CV
PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Advertisement

Table of Contents
loading

Related Manuals for Oliver 732-N

Summary of Contents for Oliver 732-N

  • Page 1 Grand Rapids, Michigan, U.S.A. 49504-5298 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 732-N BREAD SLICER 0732S20000-CV PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...

  • Page 2: Table Of Contents

    732-N Front Load Slicer INDEX Section Description Document No. Page No. SAFETY INSTRUCTIONS -------------------------------------- 0732S20002 --------------------------- 1-1 DESCRIPTION/SPECIFICATIONS --------------------------- 0732S20003---------------------------- 2-1 Description -------------------------------------------------------------------------------------------------- 2-1 Specifications----------------------------------------------------------------------------------------------- 2-1 INSTALLATION INSTRUCTIONS ---------------------------- 0732S20004 --------------------------- 3-1 Slicer Installation ------------------------------------------------------------------------------------------ 3-1 OPERATING INSTRUCTIONS -------------------------------- 0732S20005 --------------------------- 4-1...
  • Page 3 732-N Front Load Slicer INDEX (Continued) REPLACEMENT PARTS SECTION (Continued) Section Description Document No. Page No. COVERS ------------------------------------------------------------ 0732S20010 --------------------------- 9-1 Drawing ------------------------------------------------------------------------------------------------ 9-1 Parts List ----------------------------------------------------------------------------------------------- 9-2 PUSHER ------------------------------------------------------------ 0732S20011 -------------------------- 10-1 Drawing ----------------------------------------------------------------------------------------------- 10-1 Parts List ---------------------------------------------------------------------------------------------- 10-2...

  • Page 4: Safety Instructions

    732-N Front Load Slicer SAFETY INSTRUCTIONS WARNING VARIOUS SAFETY DEVICES AND METHODS OF GUARDING HAVE BEEN PROVIDED ON THIS MACHINE. IT IS ESSENTIAL HOWEVER THAT THE MACHINE OPERATORS AND MAINTENANCE PERSONNEL OBSERVE THE FOLLOWING SAFETY PRECAUTIONS. IMPROPER INSTALLATION, MAINTENANCE, OR OPERATION OF THIS EQUIPMENT COULD CAUSE SERIOUS INJURY OR DEATH.

  • Page 5: Description/Specifications

    DESCRIPTION/SPECIFICATIONS Description The Oliver Model 732-N Counter Top Bread Slicer is of a compact, sturdy, time tested design, which has been used in bakeries worldwide for many years. The machine is easy to operate and can be loaded and unloaded from the front of the machine. It is capable of slicing either hard crusted breads or soft-textured sandwich loaves with ease and precision.
  • Page 6 732-N Front Load Slicer Product Capacities: Length 16 Inches Width 5-1/2 inches (See Note) Height 5-1/2 inches (See Note) NOTE WIDTH AND HEIGHT DIMENSIONS ARE FOR A SQUARE PRODUCT. LOWER AND WIDER PRODUCTS MAY ALSO BE SLICED BY TAKING CARE IN LOADING THE PRODUCT.

  • Page 7: Installation Instructions

    732-N Front Load Slicer INSTALLATION INSTRUCTIONS Slicer Installation: Before starting the Installation process make sure you observe the following three caution notes. CAUTION THE SLICER IS HEAVY, USE PROPER TECHNIQUE WHEN LIFTING. KEEP BACK STRAIGHT, KNEES BENT, AND LIFT WITH LEGS.

  • Page 8: Operating Instructions

    732-N Front Load Slicer OPERATING INSTRUCTIONS WARNING ALWAYS USE CARE WHENEVER WORKING NEAR THE CUTTING KNIVES. To operate the slicer, stand in front of the machine and grasp the lever with your right hand. Pull the lever all the way down and hold it in that position. Using your left hand load the product into the machine.
  • Page 9 732-N Front Load Slicer Operating Instructions (Continued) When the slicing operation is complete the machine will automatically stop. Once stopped, remove the product from the cradle. Use of the standard front mounted bagging scoop will ease packaging of your product.

  • Page 10: Troubleshooting

    732-N Front Load Slicer TROUBLE SHOOTING WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK, INCLUDING TROUBLESHOOTING. The Slicer Will Not Start (Motor Is Not Humming) • The machine is not plugged in.

  • Page 11: The Slicer Will Not Start (Motor Is Humming)

    732-N Front Load Slicer Trouble Shooting (Continued) The Slicer Will Not Start (Motor Is Humming) CAUTION DO NOT ALLOW THE MOTOR TO HUM WITHOUT STARTING. OVERHEATING CAN PERMANENTLY DAMAGE THE MOTOR. NOTE A SPECIAL NON-VENTILATED MOTOR MUST BE USED WITH THIS SLICER.

  • Page 12: Bread Slices Vary In Thickness

    732-N Front Load Slicer Trouble Shooting (Continued) Bread Slices Vary in Thickness • The blade frames are out of adjustment. (See the “Maintenance” section of this manual under “Adjusting the Blade Frames When Slices Vary in Thickness” on how to correct this problem.) The Blade Frames Are Knocking •...

  • Page 13: The Bread Is Cutting Slowly Or Is Being Damaged

    732-N Front Load Slicer Trouble Shooting (Continued) The Bread is Cutting Slowly or is Being Damaged • The product you are attempting to slice is below the minimum height capacity of the machine. • You are pushing the lever of the machine in an attempt to speed slicing. This may not only damage the product but may also damage the machine.

  • Page 14: Maintenance

    732-N Front Load Slicer MAINTENANCE Removing The Blade Frames WARNING ALWAYS UNPLUG THE SLICER BEFORE PERFORMING ANY TYPE OF MAINTENANCE TASK. Remove the bagging scoop, the top and front covers by removing the ten knobs which secure them. Only remove the infeed table in the event that you MUST remove the lower blade frame.
  • Page 15 732-N Front Load Slicer Removing The Blade Frames (Continued) NOTE DO NOT LOOSEN THE NUTS WHICH SECURE THE ECCENTRIC PINS. Pull the clip from the eccentric pin and slide the link toward the eccentric pin mounting plate. See the illustration below.
  • Page 16 732-N Front Load Slicer Removing The Blade Frames (Continued) WARNING BLADES ARE EXTREMELY SHARP ALWAYS HANDLE BLADE FRAMES WITH CARE. Carefully lift the upper blade frame from the slicer. NOTE REMOVAL OF THE LOWE BLADE FRAME IS NOT REQUIRED TO CHANGE ITS BLADES...

  • Page 17: Replacing The Blade Frames

    732-N Front Load Slicer Replacing The Blade Frames WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. Replacement of the blade frames is done by reversing the removal procedures. Ensure that the feet of the blade frames rest snuggly on the swing shafts and that you have included the Belleville washers with the eye bolts.

  • Page 18: Changing The Blades

    732-N Front Load Slicer Changing The Blades WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. WARNING BLADES ARE EXTREMELY SHARP ALWAYS HANDLE WITH CARE. NOTE WHEN REPLACING ALL THE BLADES, ALWAYS REMOVE AND REPLACE ONE BLADE AT A TIME.
  • Page 19 732-N Front Load Slicer Changing The Blades (Continued) The new knife can be installed in the upper blade frame by reversing the removal procedure. A paper clip can be used to hold the knife in position on the lower pin to ease installation.

  • Page 20: Tightening The Belt

    732-N Front Load Slicer Tightening the Belt WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. CAUTION OVER-TIGHTENING THE DRIVE BELT MAY CAUSE BEARING OR MOTOR FAILURE. Remove the top cover by removing the six knobs which secure it. Then using a wrench loosen, but do not remove, the four nuts which secure the motor mounting plate to the machine.

  • Page 21: Replacing The Belt

    732-N Front Load Slicer Replacing the Belt WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. Remove the top cover by removing the six knobs which secure it. Using a wrench, loosen but do not remove the four nuts which secure the motor mounting plate to the machine.

  • Page 22: Replacing The Gas Spring

    732-N Front Load Slicer Replacing The Gas Spring WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. The Gas Spring is located on the right hand side of the machine, therefore the right hand cover must be removed.
  • Page 23 732-N Front Load Slicer Replacing the Gas Spring (Continued) WARNING THE GAS SPRING IS IN A COMPRESSED STATE, USE CARE WHEN REMOVING IT FROM THE MACHINE. To remove the gas spring, remove the push-on clip at the top of the gas spring by prying it off with a screw driver.
  • Page 24 732-N Front Load Slicer Replacing the Gas Spring (Continued) Using two people, grasp the spring as shown in the next illustration and slide the gas spring over the same upper pin that the old gas spring was removed from. See the caution statement below.

  • Page 25: Adjusting The Gas Spring

    732-N Front Load Slicer Adjusting The Gas Spring WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. CAUTION FREQUENT ADJUSTMENT OF THE GAS SPRING IS NOT RECOMMENDED. The gas spring must be removed and relocated to adjust its force. To remove the gas spring, see “Replacing the Gas Spring”...

  • Page 26: Adjusting The Blade Frames When Slices Vary In Thickness

    732-N Front Load Slicer Adjusting The Blade Frames When Slices Vary In Thickness WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. Assuming that the lower blade frame has been installed and centered in the machine, meaning that it has been aligned with the slots in the top cover and holddown, and secured with the locking cams, proceed as follows to adjust the upper blade frame.

  • Page 27: Adjusting The Clearance Between The Blade Frames

    732-N Front Load Slicer Adjusting The Clearance Between The Blade Frames WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. Start by removing the bagging scoop and the top and front covers by removing their knobs.

  • Page 28: Lubrication

    732-N Front Load Slicer Lubrication WARNING ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE TASK. Once a month put a drop of a food approved lubricant on the plastic links at the top of the blade frames.

  • Page 29: Recommended Spare Parts

    Clip-Push On 5251-0030 Bearing-5/8 Cam Follower 5251-0091 Bearing-3/4 Cam Follower *For Other Electrics Contact the Factory For Service Parts Call Oliver Products @ 800-253-3893 REV 6-8-04 0732S20008 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 30 THIS PAGE WAS INTENTIONALLY LEFT BLANK. GEN020319 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...

  • Page 31: Main Frame

    732-N Front Load Slicer MAIN FRAME REV 7/22/04 0732S20009 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...

  • Page 32: Parts List

    Knob W/Stud M5 x .8 x 15mm LG 5911-7210 Pin-Eccentric 0730-0031 Link-Blade Frame 0711-0002 Clip-Hairpin 5835-7705 NOTE: Bold text represents optional parts available FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 1/30/07 0732S20009 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 33 732-N Front Load Slicer COVERS REV. 7/22/04 0732S20010 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 34 Cover-Electrical Box 0732-0008 Cover-Electrical Box (Black) 0732-0008-002 Cover-Switch Enclosure 0732-0009 NOTE: Bold text represents optional part available FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 1/30/07 0732S20010 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 35 732-N Front Load Slicer PUSHER REV. 10/18/05 0732S20011 10-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 36 0732-0023 Washer-Special 4655-0309-1603 Bearing-3/4 Dia. Cam Follower 5251-0091 Bearing-Bronze Flange 5254-3139 Lever-Pusher 0732-0024 Knob-Ball 5911-7120 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 10/18/05 0732S20011 10-2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 37 732-N Front Load Slicer ROCKER REV. 7/22/04 0732S20012 11-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 38 Cap-Ball Bearing 4090-0232-0018 Bearing-Ball 5220-0020 Collar-Hold Down 0797-0031-002 Collar-Locating 0797-0031-003 Rod-Nylon Threaded 3/8-16 5840-8076 Cap-Clamp 0730-0023 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 7/22/04 0732S20012 11-2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 39 732-N Front Load Slicer DRIVEN PULLEY REV. 7/22/04 0732S20013 12-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 40 0730-0005-001 Stud 0797-0058-019 Stud-Swing 0797-0057-219 Rod Assembly W/Bearings 0797-0071-3 Ring-Retaining 5840-2825 Bearing-Ball 5220-5040 Ring-Retaining 5840-1040 FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 7/22/04 0732S20013 12-2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 41 732-N Front Load Slicer SLICE PARTS REV. 7/22/04 0732S20014 13-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 42 Cover-Top 0732-0015-0XX Knob W/Stud M5 x .8 x 15mm Lg. 5911-7210 * Specify Slice Thickness FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 Rev. 8/11/04 0732S20014 13-2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 43 732-N Front Load Slicer ELECTRICAL PARTS REV. 12/13/05 0732S20015 14-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 44 Plug-Hole 5769-3008 Green Grounding Screw 6-32 3/8” 5841-9501 For other Electrics Consult the Factory Continued FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV 10/5/06 0732S20015 14-2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 45 Nameplate-Wiring Diagram (Single Phase) 6402-3103 Plug-Power 1-60-230 5765-2030 Plug-Hole 5769-3013 For other Electrics Consult the Factory FOR SERVICE PARTS CALL OLIVER PRODUCTS @ 800-253-3893 REV. 12/13/05 0732S20015 14-3 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 46 732-N Front Load Slicer WIRING DIAGRAM 1-60-115/230 & 1-50-110/220 • For other Electrics Consult the Factory 0732S20016 15-1 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor...
  • Page 47 Oliver) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver within one year, Freight Prepaid to Oliver’s plant in Grand Rapids, MI, then Oliver, shall, at Oliver’s option, either repair or replace the defective part, at Oliver’s expense.
  • Page 48 4. The service dealer will then complete an invoice and send it to the Customer Service Department at Oliver Products Company. 5. The Customer Service Manager of Oliver Products Company will review the invoice and returned parts, if applicable, and approve for payment.
  • Page 49 This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Products Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.

Table of Contents