Related Manuals for Oliver 702
Summary of Contents for Oliver 702
- Page 1 Grand Rapids, Michigan, U.S.A. 49504-5298 USER’S OPERATING AND INSTRUCTION MANUAL MODEL 702 MODEL 702-SE MODEL 702-SS BUN SLICERS 0702S20000-CVR...
- Page 2 MODEL 702, 702SE and 702SS BUN SLICERS INDEX SLICER SPECIFICATIONS................ 0702S20019 Description ..................0702S20019-1/2 Specifications ................0702S20019-1/2 Product Capacities ................ 0702S20019-2/2 SAFETY INSTRUCTIONS................0702S20020 DEFINITIONS ................... GEN 931118 ADJUSTMENTS..................0702S20022 Outside Side Guide ............... 0702S20022-1/2 Table Height .................. 0702S20022-1/2 Inside Side Guide ................0702S20022-1/2 Slow-Down Door ................
-
Page 3: Specifications
MODEL 702, 702SE and 702SS BUN SLICERS SPECIFICATIONS DESCRIPTION These bun slicers have welded steel frames and stainless steel chutes. They are compact, durable slicers for counter top use in slicing a variety of buns with speed and economy. SPECIFICATIONS •... - Page 4 MODEL 702, 702SE and 702SS BUN SLICERS • Machine dimensions: Model 702SS • Weight: Approximately (70) pounds. • Standard Color: Gloss white enamel. • Standard Electrical Service: 1/3 HP, 1725 RPM, 1-60-115 Volts AC, 6 Amps. • Optional Electrical Services: 1/3 HP, 1725 RPM, 1-60-230 Volts AC, 3.5 Amps.
-
Page 5: Safety Instructions
MODEL 702, 702SE and 702SS BUN SLICERS SAFETY INSTRUCTIONS Every effort has been made by Oliver Products Company to provide you with a safe machine. It is essential, however, that machine operators and maintenance personnel observe the following safety precautions. - Page 6 GENERAL DEFINITIONS The use of the words WARNING, CAUTION, and NOTE in this manual should be guided by the following. WARNING AN OPERATING PROCEDURE, TECHNIQUE, ETC., WHICH MAY RESULT IN PERSONAL INJURY IF NOT CAREFULLY FOLLOWED. CAUTION AN OPERATING PROCEDURE, TECHNIQUE, ETC., WHICH MAY RESULT IN DAMAGE TO EQUIPMENT IF NOT CAREFULLY FOLLOWED.
- Page 7 MODEL 702, 702SE and 702SS BUN SLICERS ADJUSTMENTS WARNING NEVER ATTEMPT TO ADJUST OR SERVICE THIS MACHINE UNTIL YOU ARE SURE THE BLADE HAS STOPPED. OUTSIDE SIDE GUIDE This guide is used to determine the amount of "Hinge" left on the product and can be adjusted from leaving approximately a 1/2"...
- Page 8 MODEL 702, 702SE and 702SS BUN SLICERS If it seems necessary to adjust this guide loosen the two knobs which are on the top and to the inside of the table, then slide the guide in or out to conform with product width.
- Page 9 END OF THE CHUTE. KEEP YOUR HANDS AWAY FROM THE MOVING PARTS OF THE MACHINE. On Model 702 machines, should the sliced bun stop under the discharge door, the next bun through the blade will generally dislodge it. If this does not happen, re-adjust the slow down door or inside guide, see adjustment section of this manual.
- Page 10 MODEL 702, 702SE and 702SS BUN SLICERS MAINTENANCE/CLEANING/LUBRICATION WARNING NEVER ATTEMPT TO CLEAN OR SERVICE THIS MACHINE UNTIL IT HAS BEEN DISCONNECTED FROM THE POWER SUPPLY AND YOU ARE SURE THE BLADE HAS STOPPED. ALSO REMEMBER TO USE CARE WHENEVER YOU ARE WORKING NEAR THE BLADE.
-
Page 11: Changing The Blade
MODEL 702, 702SE and 702SS BUN SLICERS CHANGING THE BLADE WARNING NEVER ATTEMPT TO CLEAN OR SERVICE THIS MACHINE UNTIL IT HAS BEEN DISCONNECTED FROM THE POWER SUPPLY AND YOU ARE SURE THE BLADE HAS STOPPED. ALSO REMEMBER TO USE CARE WHENEVER YOU ARE WORKING NEAR THE BLADE. -
Page 12: Troubleshooting
MODEL 702, 702SE and 702SS BUN SLICERS TROUBLE SHOOTING WARNING NEVER ATTEMPT TO CLEAN OR SERVICE THIS MACHINE UNTIL IT HAS BEEN DISCONNECTED FROM THE POWER SUPPLY AND YOU ARE SURE THE BLADE HAS STOPPED. THE SLICER MOTOR WILL NOT START. - Page 13 MODEL 702, 702SE and 702SS BUN SLICERS REPLACEMENT PARTS LIST ITEM NO. PART DESCRIPTION PART NUMBER Frame 0702-0010-003 Adapter-Blade 0702-0025 Guard-Blade 0700-0003 Screw-Clamp 4560-2510-1104 Bushing-Strain Relief 5765-1071 Screw-Thumb 3/6-16 x 1-1/2 5843-0545 Foot-Rubber 5902-0011 Knife-Scalloped StSt 7107-7053 Guide-Outside (Model 702)
- Page 14 MODEL 702, 702SE and 702SS BUN SLICERS ASSEMBLY DRAWING MODEL 702 REV. 7/7/10 0702S20021...
- Page 15 MODEL 702, 702SE and 702SS BUN SLICERS ASSEMBLY DRAWING MODEL 702SE REV 7/7/10 0702S20029...
- Page 16 MODEL 702, 702SE and 702SS BUN SLICERS ASSEMBLY DRAWING MODEL 702SS REV 7/7/10 0702S20030...
-
Page 17: Wiring Diagrams
MODEL 702, 702SE and 702SS BUN SLICERS WIRING DIAGRAMS Wiring Diagram (1/3 HP, 1Ph, 50/60 Hz, 115 VAC) Diagram No. 0702C12007 Wiring Diagram (1/3 HP, 1Ph, 50/60 Hz, 230 VAC) Diagram No. 0702C12008 0702S20025... -
Page 18: Warranty
Oliver Packaging & Equipment Company (Oliver) warrants that if any part of the equipment (other than a part not manufactured by Oliver) proves to be defective (as defined below) within one year after shipment, and if Buyer returns the defective part to Oliver within one year, Freight Prepaid to Oliver’s plant in Grand Rapids, MI, then Oliver, shall, at Oliver’s option, either repair or replace the... -
Page 19: Warranty Procedure
4. The service dealer will then complete an invoice and send it to the Parts and Service Department at Oliver Products Company. 5. The Parts and Service Manager of Oliver Packaging and Equipment Company will review the invoice and returned parts, if applicable, and approve for payment. -
Page 20: Returned Parts Policy
This policy applies to all parts returned to the factory whether for warranted credit, replacement, repair or re-stocking. Oliver Packaging and Equipment Company requires that the customer obtain a Return Material Authorization (RMA) number before returning any part. This number should appear on the shipping label and inside the shipping carton as well.
Need help?
Do you have a question about the 702 and is the answer not in the manual?
Questions and answers