Agilent Technologies N6700 Series User Manual page 69

SCPI Command
OUTPut (continued)
:PROTection
:CLEar (@chanlist)
:COUPle <Bool>
:DELay <NRf+>, (@chanlist)
:RELay [:STATe] <Bool>, (@chanlist)
SENSe
:CURRent [:DC]
:RANGe [:UPPer] <NRf+>, (@chanlist)
:FUNCtion "VOLTage" | "CURRent", (@chanlist)
:SWEep
:OFFSet:POINts <NRf+>, (@chanlist)
:POINts <NRf+>, (@chanlist)
:TINTerval <NRf+>, (@chanlist)
:VOLTage [:DC]
:RANGe [:UPPer] <NRf+>, (@chanlist)
:WINDow [:TYPE] HANNing | RECTangular, (@chanlist)
[SOURce:]
CURRent
[:LEVel]
[:IMMediate][:AMPLitude] <NRf+>, (@chanlist)
:TRIGgered [:AMPLitude] <NRf+>, (@chanlist)
:MODE FIXed | STEP | LIST, (@chanlist)
:PROTection
:STATe <Bool>, (@chanlist)
:RANGe <NRf+>, (@chanlist)
DIGital
:INPut:DATA?
:OUTPut:DATA <NRf>
:PIN1 | :PIN2 | :PIN3
:FUNCtion DIO | DINP | TOUT | TINP | FAUL
:POLarity POSitive | NEGative
LIST
:COUNt <NRf+> | INFinity, (@chanlist)
:CURRent [:LEVel] <NRf> {,<NRf>. . .}, (@chanlist)
:POINts? (@chanlist)
:DWELl <NRf> {,<NRf>. . .}, (@chanlist)
:POINts? (@chanlist)
:STEP ONCE | AUTO, (@chanlist)
:TERMinate
:LAST <Bool>, (@chanlist)
:TOUTput
:BOSTep[:DATA] <Bool> {,<Bool>. . .}, (@chanlist)
:POINts? (@chanlist)
:EOSTep[:DATA] <Bool> {,<Bool>. . .}, (@chanlist)
:POINts? (@chanlist)
:VOLTage[:LEVel] <NRf> {,<NRf>. . .}, (@chanlist)
:POINts? (@chanlist)
STEP
:TOUTput <Bool>, (@chanlist)
Series N6700 User's Guide
Description
Resets latched protection
Enables/disables channel coupling for protection faults
Sets over-current protection programming delay
Sets the relay state independently of the output state (Note 3)
Selects the current measurement range (Note 4)
Selects the measurement function
Defines the trigger offset in the measurement sweep (Note2)
Defines the number of data points in the measurement (Note 2)
Sets the measurement sample interval (Note 2)
Selects the voltage measurement range (Note 4)
Sets measurement window function (Note 2)
Sets the output current
Sets the triggered output current
Sets the current trigger mode
Enables/disables over-current protection on the selected output
Sets the output current range (Note 4)
Reads the state of the digital port pins
Sets the digital port
| INH Sets the selected pin's function (
1 2
Sets the selected pin's polarity
Sets the list repeat count (Note 2)
Sets the current list (Note 2)
Returns the number of current list points (Note 2)
Sets the list of dwell times (Note 2)
Returns the number of dwell list points (Note 2)
Specifies how the list responds to triggers (Note 2)
Sets the list termination mode (Note 2)
Sets the steps to generate triggers at the Begin Of Step (Note 2)
Returns the number of beginning of step list points (Note 2)
Sets the steps to generate triggers at the End Of Step (Note 2)
Returns the number of end of step list points (Note 2)
Sets the voltage list (Note 2)
Returns the number of voltage level points (Note 2)
Generate a trigger output on the voltage or current step transient
SCPI Command Summary
PIN1 only; PIN3 only)
1 2
69