IBASE Technology IPPCxxB9-RE Series User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

www.ibase.com.tw

IPPCxxB9-RE Series

User Manual

IBASE Technology Inc.

Table of Contents

Need help?

Do you have a question about the IPPCxxB9-RE Series and is the answer not in the manual?

Questions and answers

Summary of Contents for IBASE Technology IPPCxxB9-RE Series

Page 1 IPPCxxB9-RE Series User Manual IBASE Technology Inc.
Page 3 IPPCxxB9-RE User Manual Copyright © 2013 IBASE Technology Inc. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of IBASE Technology INC.
Page 4: Table Of Contents
IPPCxxB9-RE User Manual Table of Contents Safety Information ........................iii Setting up your system ....................... iii Care during use ........................iv Acknowledgments ....................... v CHAPTER 1 INTRODUCTION ..................1 1.1 General Description ....................... 1 1.2 System Specification ...................... 2 1.2.1 Hardware Specifications ..................... 2 1.2.2 Dimensions .........................
Page 5: Safety Information
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THESTORAGE TEMPERATURE MAY GO BELOW -10° C OR ABOVE 60° C. THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 6: Care During Use
IPPCxxB9-RE User Manual Care during use  Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system.  When the system is turned off, a small amount of electrical current still flows. Always unplug all power, and network cables from the power outlets before cleaning the system.
Page 7: Acknowledgments
FINTEK is a registered trademark of FINTEK Electronics Corporation.  REALTEK is a registered trademark of REALTEK Electronics Corporation.  All other product names or trademarks are properties of their respective owners. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 9: Chapter 1 Introduction
IPPCxxB9-RE User Manual CHAPTER 1 INTRODUCTION 1.1 General Description IPPCxxB9-RE series is a fanless panel pc, powered by the 2nd Generation Intel ® Core i3-2340UE that runs at 1.3GHz. It supports 2x SO-DIMM to fit up to 16GB DDRIII 1333MHz FSB memory size, 4x USB connectors, 3x COM ports, 1x SATA HDD space, 1x CFast slot, 2x PCI expansion slots and DC power 12~24V input.
Page 10: System Specification
IPPCxxB9-RE User Manual 1.2 System Specification 1.2.1 Hardware Specifications Model Name IPPC15B9-RE IPPC17B9-RE IPPC19B9-RE System Mainboard IB907 ® 2nd Generation Intel Core i3-2340UE ® Chipset Intel HM76 PCH Memory 2x DDR3 1333 SO-DIMM up to 16GB 1x DVI-I connector I/O Interface 3x DB9 for COM1/2(RS-232/422/485), COM 3 (RS-232 only) 1x 10-pin terminal block for Digital I/O 2x RJ45 for GbE LAN...
Page 12 IPPCxxB9-RE User Manual IPPC17B9-RE...
Page 14: I/O View
IPPCxxB9-RE User Manual 1.2.3 I/O View 1.3 Packing List Part No. Description Quantity Terminal block for power input & GPIO 2 pcs Mounting Kits 1 set Driver CD 1 pc...
Page 15: Installation
1. Unlock and remove 15 screws as in the picture below and open the back cover. 2. Put the memory module into the socket. 3. Place the memory module into the socket and press it firmly. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 16: Installing Storage
IPPCxxB9-RE User Manual 1.4.2 Installing Storage 1. Unlock and remove 15 screws as in the picture below and open the back cover. 2. Unlock and remove 4 screws and SATA connector as shown.
Page 17: Installing Cfast
1.4.3 Installing CFast 1. Unlock and remove the screw as shown. 1.4.4 Installing PCI slot 1. Unlock and remove 15 screws as in the picture below and open the back cover. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 18 IPPCxxB9-RE User Manual 2. Unlock and remove the 2 screws from PCI slot cover. 3. Remove the PCI slot cover and PCI cover bracket from inside. 4. Install the PCI card and put on the PCI cover bracket and lock the screw. (The image below is for reference only.)
Page 19: Installing Wifi Module
1.4.5 Installing WIFI module 1. Push the WIFI module into the slot and use a screwdriver to turn the screw to its unlocked position. (The image below is for reference only.) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 20: Installing The Panel Mount
IPPCxxB9-RE User Manual 1.4.6 Installing the Panel Mount 1. Please assembly the screw and mounting kit as shawn picture. 2. Install the mounting kit into the panel edge as shawn picture. 3. Put the panel mount from A to E...
Page 22: Installing The Vesa Mount
IPPCxxB9-RE User Manual 1.4.7 Installing the VESA Mount 1. The VESA mount holes are compatible with VESA standard - 75x75 and 100x100 2. Put your VESA mounting kit on the red area as shown above. 3. Lock the screws from A to D.
Page 23: Chapter 2 Motherboard Introduction
24-bit dual channels LVDS interface from HM76 DVI-I x1 ® Intel 82579V GbE LAN as 1st LAN ® Realtek 8111E (GbE) as 2nd LAN ® Audio Intel HM76 PCH built-in HD Audio controller + Realtek ALC662 Codec Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 24 IPPCxxB9-RE User Manual ® USB 2.0 Intel HM76 integrated USB 2.0 host controller: 1. 4ports in the rear panel (2x USB2.0; 2x USB3.0) 2. 2 ports (USB3.0) via edge golden-finger for connector ID912 3. 2 ports via onboard Mini-PCIE 4. 2 ports via edge golden-finger for connecting with ID912 5.
Page 25 - 14-pin LED light header for COM (Tx and Rx) and LAN (Link and active) - GPIO x5-pin (4-pin for panel selection 1-pin for backlight) - 2x10 pins for front panel USB3.0 x2 Board Dimensions Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 26: Installing The Memory
IPPCxxB9-RE User Manual 2.2 Installing the Memory The IB907 board supports two DDR3 memory sockets for a maximum total memory of 16GB in DDR3 SO-DIMM memory type. Installing and Removing Memory Modules To install the DDR3 modules, locate the memory slot on the board and perform the following steps: 1.
Page 27: Setting Jumpers
The following lists the connectors on IB907 and their respective functions. Jumper Locations on IB907 JP1: Clear CMOS Contents Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear CMOS Short/Closed Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 28 IPPCxxB9-RE User Manual JP2: COM1 RS232 RI/+5V/+12V Power Setting Setting Function Pin 1-2 +12V Short/Closed Pin 3-4 Short/Closed Pin 5-6 Short/Closed JP3: COM2 RS232 RI/+5V/+12V Power Setting Setting Function Pin 1-2 +12V Short/Closed Pin 3-4 Short/Closed Pin 5-6 Short/Closed...
Page 29: Connectors
IBASE Technology Inc. 2.4 Connectors Connector Locations on IB907 CN1: COM1 and COM2 Serial Ports Pin # Signal Name RS-232 R2-422 RS-485 DATA- DATA+ Ground Ground Ground Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 30 IPPCxxB9-RE User Manual CN2: COM3 and DVI-I Connector Signal Name Pin # Pin # Signal Name Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send Data terminal ready RI, Ring indicator GND, ground Not Used...
Page 31 Signal Name Pin # Pin # Signal Name Power BTN Power BTN HDD LED+ HDD LED- Reset BTN Reset BTN Power LED+ Power LED- J7: SPI Flash Connector (Factory use only) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 32 IPPCxxB9-RE User Manual J9: ATX Power Supply Connector Signal Name Pin # Pin # Signal Name 3.3V 3.3V -12V 3.3V Ground Ground PS-ON Ground Ground Ground Ground Ground Power good 5VSB +12V J8: DDR SO-DIMM Channel A J13: DDR SO-DIMM Channel B J10: Mini-PCIE Connector J11: Mini-PCIE Connector and mSATA/share J12, J14: SATA3 Connector...
Page 33 PCIE1: PCIEx8 Golden Finger (Include, USB2.0x2, COMx1, LVDS dual Channel 24bit Signal) PCIE2: PCIEx8 Golden Finger (Include DVI, USB2.0x2, USB3.0x2, LED,) PCIE3: PCIEx16 Golden Finger (Include PCI 32bit master x2, USBx1, COMx1, PCIEx1 Signal) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 34: Chapter 3 Bios Setup
IPPCxxB9-RE User Manual CHAPTER 3 BIOS SETUP 3.1 BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
Page 35: Main Settings
System Language Choose the system default language. System Date Set the Date. Use Tab to switch between Data elements. System Time Set the Time. Use Tab to switch between Data elements. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 36 IPPCxxB9-RE User Manual Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility Advanced Main Chipset Boot Security Save & Exit ► PCI Subsystem Settings ►...
Page 37 Enables or disables VGA Palette Registers Snooping. PERR# Generation Enables or disables PCI device to generate PERR#. SERR# Generation Enables or disables PCI device to generate SERR#. PCI Express Settings Change PCI Express devices settings. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 38 IPPCxxB9-RE User Manual PCI Express Settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit PCI Express Device Register Settings Relaxed Ordering Disabled Extended Tag Disabled No Snoop Enabled Maximum Payload Auto Maximum Read Request Auto PCI Express Link Register Settings →...
Page 39 Select ACPI sleep state the system will enter, when the SUSPEND button is pressed. Lock Legacy Resources Enabled or Disabled Lock of Legacy Resources. S3 Video Repost Enable or disable S3 Video Repost. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 40 IPPCxxB9-RE User Manual Wake up event settings Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Wake on Ring Disabled → ← Select Screen Wake on PCI PME Disabled ↑↓Select Item Enter: Select Wake on PCIE Wake Event Disabled +- Change Field F1: General Help...
Page 41 When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Hardware Prefetcher To turn on/off the Mid level Cache (L2) streamer Prefetcher. Adjacent Cache Line Prefetch To turn on/off prefetching of adjacent cache lines. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 42 IPPCxxB9-RE User Manual SATA Configuration SATA Devices Configuration. Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit SATA Controller(s) Enabled SATA Mode Selection SATA Port0 Empty Software Preserve Unknown SATA Port1 Empty Software Preserve Unknown → ← Select Screen SATA Port2 Empty ↑↓Select Item...
Page 43 F2: Previous Values F3: Optimized Default F4: Save ESC: Exit ISmart Controller Setup the power on time for the system. Schedule Slot 1 / 2 Setup the hour/minute for system power on. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 44 IPPCxxB9-RE User Manual Acoustic Management Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Acoustic Management Configuration → ← Select Screen ↑↓Select Item Acoustic Management Disabled Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit USB Configuration...
Page 45 Maximum time the device will take before it properly reports itself to the Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 46 IPPCxxB9-RE User Manual F81866 Super IO Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Super IO Configuration F81866 F81866 Super IO Chip F81866 ERP Support All Enable → ← Select Screen ↑↓Select Item ► Serial Port 0 Configuration Enter: Select ►...
Page 47: Chipset Settings
► PCH-IO Configuration → ← Select Screen ► System Agent (SA) Configuration ↑↓Select Item Enter: Select +- Change Field F1: General Help F2: Previous Values F3: Optimized Default F4: Save ESC: Exit Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 48 IPPCxxB9-RE User Manual PCH-IO Configuration This section allows you to configure the North Bridge Chipset. Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Intel PCH RC Version 1.1.0.0 Intel PCH SKU Name HM76 Intel PCH Rev ID O4/C1 ►...
Page 49 The control of Active State Power Management on both NB side and SB side of the DMI link. PCIe-USB Glitch W/A PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 50 IPPCxxB9-RE User Manual USB Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit USB Configuration XHCI Pre-Boot Driver Disabled xHCI Mode Auto HS Port #1 Switchable Enabled HS Port #2 Switchable Enabled HS Port #3 Switchable Enabled HS Port #4 Switchable Enabled xHCI Streams...
Page 51 F3: Optimized Default ► Graphics Configuration F4: Save ESC: Exit ► Memory Configuration Enable NB CRID Enable or disable NB CRID WorkAround. C-State Pre-Wake Controls C-State Pre-Wake feature for ARAT, in SSKPD[57]. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 52 IPPCxxB9-RE User Manual Graphics Configuration Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Graphics Configuration IGFX VBIOS Version 2137 IGfx Frequency 650 MHz → ← Select Screen ↑↓Select Item Primary Display Auto Enter: Select Internal Graphics Auto +- Change Field GTT Size F1: General Help...
Page 53 CAS Latency (tCL) +- Change Field F1: General Help Minimum delay time F2: Previous Values CAS to RAS (tRCDmin) F3: Optimized Default Row Precharge (tRPmin) F4: Save ESC: Exit Active to Precharge (tRASmin) Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 54 IPPCxxB9-RE User Manual Boot Settings This section allows you to configure the boot settings. Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Boot Configuration Setup Prompt Timeout Bootup NumLock State Quiet Boot Disabled Fast Boot Disabled → ← Select Screen CSM16 Module Version 07.69 ↑↓Select Item...
Page 55 Launch Video OpROM policy Controls the execution of UEFI and Legacy Video OpROM. Other PCI device ROM priority For PCI devices other than Network, Mass storage or Video defines which OpROM to launch. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 56 IPPCxxB9-RE User Manual Security Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limit access to Setup and is only asked for when entering Setup.
Page 57 Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 58: Chapter 4 Drivers Installation
IPPCxxB9-RE User Manual CHAPTER 4 DRIVERS INSTALLATION This section describes the installation procedures for software and drivers. The software and drivers are included with the motherboard. IMPORTANT NOTE: After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation.
Page 59 IBASE Technology Inc. 2. Click Intel(R) Chipset Software Installation Utility.. 3. When the Welcome screen to the Intel® Chipset Device Software appears, click Next to continue. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 60 IPPCxxB9-RE User Manual 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On the Readme File Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect.
Page 61: Vga Drivers Installation
To install the VGA drivers, follow the steps below. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) 7 Series Chipset Drivers. 2. Click Intel(R) 7 Series Chipset Family Graphics Driver. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 62 IPPCxxB9-RE User Manual 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to to agree with the license agreement and continue the installation.
Page 63 5. On the Readme File Information screen, click Next to continue the installation of the Intel® Graphics Media Accelerator Driver. 6. On Setup Progress screen, click Next to continue. 7. Setup complete. Click Finish to restart the computer and for changes to take effect. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 64: Realtek Hd Audio Driver Installation
IPPCxxB9-RE User Manual 4.3 Realtek HD Audio Driver Installation Follow the steps below to install the Realtek HD Audio Drivers. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) 7 Series Chipset Drivers. 2. Click Realtek High Definition Audio Driver.
Page 65 3. On the Welcome to the InstallShield Wizard screen, click Next to proceed with and complete the installation process. 4. The InstallShield Wizard Complete. Click Finish to restart the computer and for changes to take effect. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 66: Lan Drivers Installation
IPPCxxB9-RE User Manual 4.4 LAN Drivers Installation 1. Insert the CD that comes with the board. Click Intel and then Intel(R) 7 Series Chipset Drivers. 2. Click Intel(R) PRO LAN Network Driver.
Page 68 IPPCxxB9-RE User Manual 5. Click Next to to agree with the license agreement. 6. Click the checkbox for Drivers in the Setup Options screen to select it and click Next to continue.
Page 69 IBASE Technology Inc. 7. The wizard is ready to begin installation. Click Install to begin the installation. 8. When InstallShield Wizard is complete, click Finish. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 70: Realtek Lan Controller Drivers Installation
IPPCxxB9-RE User Manual 4.5 Realtek LAN Controller Drivers Installation Follow the steps below to install the Realtek LAN Drivers. 1. Insert the CD that comes with the board. Click Intel, then LAN Card, and then Realtek LAN Controller Drivers. 2. Click Realtek RTL8111E LAN Drivers.
Page 71 IBASE Technology Inc. 3.When the welcome screen to InstallShield Wizard appears, click Next to start the installation 4.When the InstallShieldWizard has finished installing the Realtek LAN drivers, click Finish. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 72: Intel® Management Engine Interface
IPPCxxB9-RE User Manual 4.6 Intel® Management Engine Interface Follow the steps below to install the Intel Management Engine. 1. Insert the CD that comes with the board. Click Intel and then Intel(R) AMT 8.0 Drivers. 2. When the Welcome screen to the InstallShield Wizard for Intel® Management Engine Components, click the checkbox for Install Intel®...
Page 73 IBASE Technology Inc. 3. Click Yes to to agree with the license agreement. 4. When the Setup Progress screen appears, click Next. Then, click Finish when the setup progress has been successfully installed. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 74: Intel® Usb 3.0 Drivers
IPPCxxB9-RE User Manual 4.7 Intel® USB 3.0 Drivers 1. Insert the CD that comes with the board. Click Intel and then Intel(R) 7 Series Chipset Drivers. 2. Click Intel(R) USB 3.0 Drivers.
Page 75 3. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0 eXtensible Host Controller Driver, click Next. 4. Click Yes to to agree with the license agreement and continue the installation. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Page 76 IPPCxxB9-RE User Manual 5. On the Readme File Information screen, click Next to continue the installation of the Intel® USB 3.0 eXtensible Host Controller Driver. 6. Setup complete. Click Finish to restart the computer and for changes to take effect.
Page 77: Altera Fpga Driver Installation
Setup Wizard screen appears, click Next to continue. 3. When the Ready to Install screen appears, click Install to continue. 4. The Setup process is now complete, Click Finish to restart the computer. Copyright © 2013 IBASE Technology Inc. All Rights Reserved.

IBASE Technology IPPCxxB9-RE Series User Manual

Chapter 1 Introduction

Chapter 2 Motherboard Introduction

Chapter 3 Bios Setup

Chapter 4 Drivers Installation

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for IBASE Technology IPPCxxB9-RE Series

Summary of Contents for IBASE Technology IPPCxxB9-RE Series

Table of Contents