Connect Power; Overseas Development Kits - Rabbit RCM3000 User Manual

2.2.3 Connect Power

When all other connections have been made, you can connect power to the Prototyping
Board.
Connect the wall transformer to jack J11 on the Prototyping Board as shown in Figure 3
below.
RN1
GND NC PD1
GND
+3.3V PD7
VBAT
VRAM PD3
EXT
/RES
SM1 PD5
IN
SM0 /IORD PG3
/IOWR PG4 PG1
PG5 PG6
PC7
PG7
PE0 PC5
PE1 PE3 PC3
PE4 PE5 PC1
PE6 PE7 PF0
PF7 PF6 PF2
PF5 PF4
PA0
PB7 PB6 PA2
PB5 PB4 PA4
PB3 PB2 PA6
PB0 /RES STAT
J3
J1
RN2
C1
C2
R1
R2
IR1
RC13
RC12
R21
RC10
RC11
GND NC PD1
GND +3.3V PD7
VBAT
VRAM PD3
EXT
/RES
SM1 PD5
IN
SM0 /IORD PG3
/IOWR PG4 PG1
PG5 PG6 PD4
PG7 PE0 PC5
PE1 PE3 PC3
PE4 PE5 PC1
PE6 PE7 PF0
PF7 PF6 PF2
PF5 PF4 PA0
PB7 PB6 PA2
PB5 PB4 PA4
PB3 PB2 PA6
PB0 /RES STATUS
J2 J4
Plug in the wall transformer. The power LED on the Prototyping Board should light up.
The RCM3000 and the Prototyping Board are now ready to be used.
NOTE: A RESET button is provided on the Prototyping Board to allow hardware reset
To power down the Prototyping Board, unplug the power connector from J11. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RCM3000 from the Prototyping Board.

2.2.3.1 Overseas Development Kits

Development kits sold outside North America include a header connector that may be
connected to 3-pin header J9 on the Prototyping Board. The connector may be attached
either way as long as it is not offset to one side. The red and black wires from the connec-
tor can then be connected to the positive and negative connections on your power supply.
The power supply should deliver 8 V–24 V DC at 8 W.
8
Downloaded from Elcodis.com electronic components distributor
TP2
GND/EGND
PD0
RCM1JA RCM1JB RN3 RN5
PD6
RCM3000 ETHERNET CORE MODULE
PD2
PD4
R17
PG2
PG0
PC6
PC4
PC2
PC0
PF1
RN4 Battery
PF3
PA1
PA3
BT1
PA5
PA7
SLAVE
UX11
GND
UX10
RC18
MASTER
RC15
RCM2
RC19
RC24
R4
RC20
RC23
UX9
C3
R5
RC14
RC17
RC22
RC16
RC21
UX3
R11
R7 R9 R13
RC2
GND
RC3
UX2
GND
GND/EGND
PD0
+3.3V
PD6
+3.3V
RCM3000 ETHERNET CORE MODULE
TP1
PD2
+5V
RC6
PD4
PG2
R15 R16
PG0
PD5
PC4
PC2 UX5
R14
RC8
PC0
PF1
UX8
U1
PF3
PA1
C5
PA3
C8
R18 R19
RCM2JA RCM2JB
PA5
C4 C6
RESET
PG7
PA7 PG6
1 C7 1 3 1 3
3 RxC TxC
GND
J5
2 4 2 4 2 4 DS1 DS2
S1 S2 S3
TxB RxB GND
Figure 3. Power Supply Connections
without disconnecting power.
3-pin
power connector
C15
L1
DS3 C17
J11
R20
D1
C13
HOT
C10
C11
2.5 mm JACK
D2
GND +DC
U4
C12
U5
+5V +5V
+3.3V +3.3V
GND GND
+5V +5V
+3.3V
J8
UX4 UX12
+3.3V
+5V
RC7
RC25
UX6
RC4 RC5
C16 DISPLAY BOARD
RC27
U6 C14
C9
RC28
U3
RC29
U2
RC26
RC9
UX7
RCM30/31/32XX SERIES
UX13
PROTOTYPING BOARD
J10 J7
DISPLAY BOARD
DISPLAY BOARD
RabbitCore RCM3000