Connect Programming Cable - Rabbit RCM3000 User Manual

2.2.2 Connect Programming Cable

The programming cable connects the RCM3000 module to the PC running Dynamic C to
download programs and to monitor the module for debugging.
Connect the 10-pin connector of the programming cable labeled
the RCM3000 module as shown in Figure 2. Be sure to orient the marked (usually red)
edge of the cable towards pin 1 of the connector. (Do not use the
used for a normal serial connection.)
Connect the other end of the programming cable to a COM port on your PC.
User's Manual
Downloaded from Elcodis.com electronic components distributor
NOTE: Be sure to use the programming cable (part number 101-0513) supplied with this
Development Kit—the programming cable has red shrink wrap around the RS-232 con-
verter section located in the middle of the cable. Programming cables with blue or clear
shrink wrap from other from other Rabbit Semiconductor kits were not designed to work
with RCM3000 modules.
RN1
GND/EGND
GND NC
PD1 PD0
RCM1JA
GND +3.3V PD7 PD6
VBAT RCM3000 ETHERNET CORE MODULE
VRAM PD3 PD2
EXT
/RES
SM1 PD5
PD4
IN
SM0
/IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PC7 PC6
PG7 PE0
PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0
PF1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4
PA4 PA5
PB3 PB2 PA6 PA7
SLAVE
PB0 /RES STAT GND
UX10
MASTER
J1 J3
RN2
C1
RC15
RCM2
C2
RC19
RC24
R1
R4
RC20
RC23
UX9
C3
R5
R2
IR1
RC14
RC17
RC22
RC16
RC21
RC13
UX3
RC12
R7 R9 R11 R13
R21
RC10
RC11
RC3
GND/EGND
GND NC PD1 PD0
GND +3.3V PD7
PD6
RCM3000 ETHERNET CORE MODULE
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3
PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
U1
PF7 PF6 PF2
PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
RCM2JA
PB5 PB4 PA4 PA5
C4
RESET
PB3 PB2 PA6 PA7
1
3 RxC TxC
PB0 /RES STATUS GND
J2 J4
2 4
S1
TxB RxB GND
Figure 2. Connect Programming Cable to RCM3000
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter with the programming cable supplied with your RabbitCore
module. An RS-232/USB converter is available through the Web store. Note that not all
RS-232/USB converters work with Dynamic C.
TP2
RCM1JB
RN3 RN5
HOT
R17
+5V
RN4
Battery
+3.3V
BT1
UX11
RC18
RC2
GND
UX2
GND
+3.3V
+3.3V +3.3V
TP1
+5V
+5V
RC6 RC7
UX6
R15 R16
C9
U2
UX5
R14
RC8
RC9
UX8 UX7
C5
C8
R18 R19
RCM2JB
C6
PG6 PG7
C7 1 3
3 1
Colored edge
J5
DS2
2 4 2 4 DS1
S2 S3
DISPLAY BOARD
to header J3 on
PROG
DIAG connector, which is
C15
L1
DS3
C17
J11
R20
D1
C13
C10
C11
2.5 mm JACK
D2
GND
+DC
U4
C12
U5
+5V
+3.3V
GND GND
+5V +5V
+3.3V
J8
UX4 UX12
RC25
RC4 RC5
C16 DISPLAY BOARD
RC27
U6
C14
To
RC28
U3
RC29
RC26
PC COM port
Colored
RCM30/31/32XX SERIES
UX13
PROTOTYPING BOARD
shrink wrap
J7
J10
DISPLAY BOARD
7