Connect Power - Rabbit RabbitCore RCM3000 Getting Started Manual

2.3.3 Connect Power

When all other connections have been made, you can connect power to the RCM3000 Pro-
totyping Board.
Connect the wall transformer to jack J11 on the Prototyping Board as shown in Figure 6
below.
RN1
GND NC PD1 PD0
RCM1JA
GND
GND +3.3V PD7 PD6
VBAT
RCM3000 ETHERNET CORE MODULE
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PF0
PE6 PE7 PF1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 PA5
PA6
PB3 PB2 PA7 SLAVE
UX10
PB0 /RES PE4 GND
MASTER
J1 J3
C1
RC15 RCM2
RC24
R1 RC19
R4
RC20
RC23
R3
UX9
C3
R5
R2
RC14
RC22
RC17
RC16
RC13
UX3
RC21
RC12
R21
RC10
RC11
GND NC PD1 PD0
GND +3.3V PD7 PD6
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1
PC0
PE6 PE7 PF0 PF1
U1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 RCM2JA
PA5
RESET
PB3 PB2 PA6 PA7
RxC TxC
PB0 /RES STATUS GND C7
J5
J4
RS-232
TxB RxB GND
Plug in the wall transformer. The power LED on the Prototyping Board should light up.
The RCM3000 and the Prototyping Board are now ready to be used.
NOTE: A RESET button is provided on the Prototyping Board to allow hardware reset
without disconnecting power.
To power down the Prototyping Board, unplug the power connector from J11. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RCM3000 from the Prototyping Board.
2.3.3.1 Overseas Development Kits
Development kits sold outside North America include a header connector that may be
connected to 3-pin header J9 on the Prototyping Board. The connector may be attached
either way as long as it is not offset to one side. The red and black wires from the connec-
tor can then be connected to the positive and negative connections on your power supply.
The power supply should deliver 8 V–30 V DC at 8 W.
Getting Started
RCM1JB RN5
R17
U4
+5V
Battery
+3.3V
BT1
J15
UX11
RC2
UX2
GND
GND
GND
+3.3V +3.3V
+3.3V +3.3V
+5V +5V
RC6 RC7
C9
U3
UX5
R14
RC9
UX7
C5
RCM30/31/32XX SERIES
C8
RCM2JB PROTOTYPING BOARD
C6
S2 S3
PG6 PG7
DS1 DS2 DISPLAY BOARD
Figure 6. Power Supply Connections
3-pin
power connector
L1
C17
J11
D1
R20 C13
2.5 MM JACK
D2 GND +DC
C12
U5
+5V
+3.3V
GND
+5V +5V
J8 UX4
RC25
RC4
C16
DISPLAY BOARD RC5
U6
C14
RC27
U3
RC28
RC29
RC26
UX13
J10 J7
DISPLAY BOARD
13