Connect Power; Overseas Development Kits - Rabbit RabbitCore RCM3000 User Manual

2.2.3 Connect Power

When all other connections have been made, you can connect power to the Prototyping
Board.
Connect the wall transformer to jack J11 on the Prototyping Board as shown in Figure 3
below.
RN1
GND/EGND
GND NC PD1
PD0
RCM1JA
GND +3.3V
PD7 PD6
VBAT RCM3000 ETHERNET CORE MODULE
VRAM PD3 PD2
EXT
/RES
SM1 PD5 PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1
PG0
PG5 PG6
PC7 PC6
PG7 PE0 PC5 PC4
PE1 PE3 PC3 PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
PF7 PF6
PF2 PF3
PF5
PF4 PA0 PA1
PB7 PB6 PA2 PA3
PB5 PB4 PA4 PA5
PB3 PB2 PA6 PA7
SLAVE
PB0 /RES STAT
GND UX10
J1 J3 MASTER
RN2
C1
RC15
RCM2
C2
RC19
RC24
R1
R4
RC20
RC23
UX9
C3
R5
R2
IR1
RC14
RC17
RC22
RC16
RC21
RC13
UX3
RC12
R7 R11
R21 R9 R13
RC10
RC11
RC3
GND/EGND
GND NC PD1 PD0
GND +3.3V PD7 PD6
RCM3000 ETHERNET CORE MODULE
VBAT
VRAM PD3 PD2
EXT
/RES
SM1 PD5
PD4
IN
SM0 /IORD PG3 PG2
/IOWR PG4 PG1 PG0
PG5 PG6 PD4 PD5
PG7 PE0 PC5 PC4
PE1 PE3 PC3
PC2
PE4 PE5 PC1 PC0
PE6 PE7 PF0 PF1
U1
PF7 PF6 PF2 PF3
PF5 PF4 PA0 PA1
PB7 PB6 PA2 PA3
RCM2JA
PB5 PB4 PA4 PA5
C4
RESET
PB3 PB2 PA6 PA7
1
3 RxC TxC
PB0 /RES STATUS GND
J2 J4 J5
2 4
S1
TxB RxB GND
RESET
Plug in the wall transformer. The power LED on the Prototyping Board should light up.
The RCM3000 and the Prototyping Board are now ready to be used.
NOTE: A RESET button is provided on the Prototyping Board to allow hardware reset
without disconnecting power.
To power down the Prototyping Board, unplug the power connector from J11. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RCM3000 from the Prototyping Board.

2.2.3.1 Overseas Development Kits

Development kits sold outside North America include a header connector that may be
connected to 3-pin header J9 on the Prototyping Board. The connector may be attached
either way as long as it is not offset to one side. The red and black wires from the connec-
tor can then be connected to the positive and negative connections on your power supply.
The power supply should deliver 8 V–24 V DC at 8 W.
8
TP2
RCM1JB RN3
RN5
HOT
R17
+5V
RN4
Battery
+3.3V
BT1
UX11
RC18
RC2
GND GND
UX2
GND
+3.3V
+3.3V
+3.3V +3.3V
TP1
+5V
+5V
RC6 RC7
UX6
R15 R16
C9
U2
UX5
R14
RC8 RC9
UX7
UX8
C5
RCM30/31/32XX SERIES
C8
R19
R18
RCM2JB PROTOTYPING BOARD
C6
PG7
PG6
C7 1 3
3 1
2 4 2 4 DS1 DS2
S2 S3
DISPLAY BOARD
Figure 3. Power Supply Connections
3-pin
power connector
C15
L1
DS3 C17
J11
R20
D1
C13
C10
C11
2.5 mm JACK
D2
GND +DC
U4
C12
U5
+5V
+3.3V
GND
+5V +5V
J8
UX4 UX12
RC25
RC4 RC5
C16 DISPLAY BOARD
RC27
U6 C14
RC28
U3
RC29
RC26
UX13
J10 J7
DISPLAY BOARD
RabbitCore RCM3000