Table of Contents
Advertisement
4.2
Before you begin
B
e
o f
e r
c
r a
y r
n i
g
o
t u
a
n
precautions:
• Make sure that the general power supply has been
disconnected.
• Make sure that all parts of the wood pellet
• Make sure that the ashes have cooled completely.
• Make sure that the general switch is in the zero position
(off).
• Make sure that the plug is disconnected from the socket,
thus avoiding accidental electric shocks.
• Always use appropriate tools for maintenance.
• When you have
before using the wood pellet
The wood pellet
requires little maintenance if quality
wood pellets are used, which is why we recommend pellet
fuel that is manufactured to the AS/NZS 4014.6.
4.3
Cleaning the surfaces
To clean the surfaces on the painted metal parts, use a
damp cloth.
Important: the use of aggressive detergents or abrasive
cleaners can damage the surfaces of the stove.
Warning: parts of the appliance, especially the
external surfaces, will be hot to touch when in
operation so use due care.
5.
Operating your Pellet Fire
5.1
Starting your Pellet Fire for the
time
1.
Load the hopper with pellets (see "5.2 Filling the
Pellet Hopper" on page 6)
2.
Make sure that the pellet
In the case of an insert pellet
be pushed back and locked securely in its cradle
with a good seal on the gasket where the exhaust
fan attaches to the
3.
Make sure the power cord is attached, turn the power
on and turn the On/Off switch at the back of the
ON. (The
will go through its shutdown routine
"FINAL CLEANING" with the exhaust/Combustion
Page 3
y
m
a
n i
e t
n
a
n
c
e
a t
k
e
h t
e
re-install all safety guards
again.
is connected to the
the unit must
adapter box.
4.4
Responsibility
o f
o l l
w
n i
g
P
l l e
t e
i F
e r
S
o
and criminal, with the delivery of this manual, for any
accidents deriving from partial or total failure to observe
the instructions it contains.
Pellet
i F
e r
S
l o
are cold.
from the improper use of the stove, from its incorrect use by
h t
e
u
s
r e
b ,
y
u
n
from the use of spare parts which are not original. The
m
a
n
u
a f
c
u t
e r
d r
responsibility due to:
• Use of poor quality fuel.
• Poor maintenance.
• Failure to observe the instructions in the manual.
• Use not compliant with the safety instructions.
• Installation that is not compliant with the regulations in
force in the country.
• Installation by personnel who are not
authorized.
•
manufacturer.
• Use of spare parts that are not original.
• Exceptional events.
4.5
Spare Parts
To avoid voiding your warranty, use original spare parts
only. Do not wait for components to be worn out before
replacing them.
Replace a worn component before it is completely broken
to prevent any accidents caused by the sudden breakage
of components. Perform the periodic maintenance checks
as described in the dedicated chapter on Maintenance
(page 13).
fan running for several minutes)
4.
Set the clock (see "6.2 Menu One - Setting the
Clock" on page 8)
5.
Set power level (1-5). For the
commissioning it should be on the highest heat
setting (level 5).
6.
Prime the Auger (see "6.6.1 Loading the Screw
A (
u
g
e
" ) r
Any build up of unburned pellets inside the
trying to light the
attempts are made. DO NOT return charred pellets to
the hopper.
u l
o i
n
s
d
e
c
n i l
e
s
l l a
e r
s
p
o
n
t u
o i
n
s
declines all responsibility deriving
a
u
h t
r o
s i
e
d
e
c
n i l
e
s
l l a
i d
e r
t c
i c
l i v
r o
c
and repairs that are not authorized by the
o
n
p
a
g
e
1
0
. )
must be removed before further
s
b i
i l i
, y t
b
o
h t
i c
l i v
and/or repairs or
i r
m
n i
l a
or
start/
pot after
5
Hide quick links:
Advertisement
Chapters
Table of Contents
