Introduction; Dimensions - Ravelli Camino Owners & Installation Manual

venting system should be inspected and cleaned at
least once every year or after every ton of pellets burnt.
We recommend contacting your dealer for professional
cleaning. To remove dust from the vent pipe, tap lightly
on the pipe to dislodge any loose ash. Open the bottom
of the adapter box and vacuum as much of the ash
1.

Introduction

out of the vent pipe as possible.
8.10 Blower Mechanisms (yearly)
This manual is designed for the technician/installer.
Pull the forward to access the two blowers. Vacuum
Please read this entire manual before operating your
all dust from motors and convection fan blades. DO
Ravelli Wood Pellet Fire.
NOT lubricate these fans they have sealed bearings.
instructions may result in poor performance, damage to
the fi re, property damage, bodily injury or even death.
8.11 Post season clean-up
Any unauthorised modifi cation of the appliance or use
of replacement parts not supplied by the manufacturer
Once you are
season, unplug the
2. Positioning and Installation of the wood pellet re
1.1. Dimensions Ravelli
2.1 Positioning
Generally the Camino should be installed in a centrally
located position within the home.
where to position the appliance, you must consider the
following:
1. The place of installation of the pellet fi re must
comply with local and national regulations. The
pellet fi re must be fuelled only with quality pellets
manufactured to standard AS/NZS 4014.6. The
pellet fi re cannot operate using traditional fi re wood
or fuel other than wood pellets.
2. Do not install a pellet fi re in a bathroom, bedroom or
room where people sleep.
3. Camino has a convection fan which blows air through
tubes in the direction the fi re faces. For optimum
performance and heat circulation, locate the pellet
Height
fi re in a large and open room that is centrally located
in the house.
Width
4. The fi re requires a 230 volt power supply and comes
with a 2m plug in power lead. There must be easy
Depth
access to the socket so the fi re can be isolated
from the power if required . If the cable supplied is
Weight
not long enough to reach the nearest outlet, use a
suitable 3 pin extension cord. A surge protector is
Diameter of smoke exhaust
recommended for use with all
Min - Max power
2.2 Installing
Min - max hourly consumption of pellets
Installation of the R v i l l a
Electrical power absorbed during operation
must be undertaken by an approved installer, who must
then give the purchaser a declaration of conformity of
Supply
the appliance, and will assume all responsibility for the
fi nal installation and consequent correct function of the
Hopper Capacity
installed product.
Space Heating
Please read this Manual thoroughly before commencing
installation, as failure to follow the instruction could cause
damage to the pellet fi re or property. It is also necessary
for the registered installer to take into consideration
all the laws and national, regional, provincial and local
Page 1
22
Failure to follow these
using the pellet appliance for the
for added electrical protection. It
( Camino)
When deciding
R v i l l a e pellet fi res.
e Camino Wood Pellet Fire
is very important that the
serviced as stated above. Exposed metal part may be
painted with high temperate paint to prevent rusting over
the off season.
8.12 Cleaning the surfaces
To clean the surfaces on the painted metal parts, use a
damp cloth.
is prohibited.
All national and local regulations shall be complied with
Important: the use of aggressive detergents or
when installing this appliance. Your local
abrasive cleaners can damage the surfaces of the
Solutions dealer will be happy to assist you in obtaining
stove.
information with regards to your local building codes and
installation regulations.
regulations present in the country in which the appliance
has been installed. In the event of failure to respect these
precautions, P l l e t e F ire Solutions
The data shown are indicative and not binding.
Ravelli reserves the right to make any
1. The fi re must be installed on a fl oor with suffi cient
for the purpose of improving the
carrying capacity. If the existing building does not
performances of the product.
meet this requirement, appropriate measures must
be taken (i.e. a load distribution plate).
2. Camino must be installed on a non-combustible
surface. This surface must protrude a minimum
of 150mm from the front of the closed pellet fi re
door and a minimum of 200mm from the side of the
appliance. Please note that if a fl oating hearth is to
be installed, an allowance must be made below the
fi re for installation of the chosen surround.
3. Check clearances to combustibles (see "5. Creating
h t e C a t i v " y o n p
is created in the cavity, and that the position of
557mm structural elements near the proposed fl ue have
adequate clearance.
705mm
4. Check clearance for service – as the Camino is
designed to be pulled out, as long as there is front
650mm
access, this should be suffi cient.
150kg
5. Check there is suffi cient ventilation for combustion
air and this is unaffected by mechanical extraction.
80mm
An external air
"5. Creating the Cavity" on page 26 for cavity
3.7Kw/h - 8.2Kw/h
ventilation requirements).
0.8kg/h - 1.9kg/h
6. There must be suffi cient circulation of air in the room
where the pellet fi re is installed. Never open the
240W
door of the pellet fi re while it is functioning.
7. Check there is a suitable fl ue location (studs, joists,
220V - 50Hz
rafters etc).
17kg
8. Camino has been Safety Tested to AS/NZS 2918:2001
using the Davins manufactured fl ue, Test Report
88%
ARS 05/1185. Installation is not exclusive to these
nominated kits, though an alternative fl ue should
only be considered following consultation with your
local council.
9. Because of the positive pressure in the fl ue, sealing
be thoroughly cleaned and
Pellet
declines all responsibility.
a g e 2 ) 6 o t e n s u e r s f u fi cent space
intake may be required. (see
F ire
Page 14