Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан alert the user of the presence of uninsulated dangerous voltage within the на...
Page 3
This interference must be corrected at the expense of the user. Class 1 Laser Product Any service to this product must be carried out by Extron Electronics and its qualified service personnel. CAUTION: Using controls, making adjustments, or performing procedures in a manner other than what is speciied herein may result in hazardous radiation exposure.
Page 4
Conventions Used in this Guide Notifications The following notifications are used in this guide: Potential risk of severe injury or death. WARNING: AVERTISSEMENT: Risque potentiel de blessure grave ou de mort. CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessure mineure. ATTENTION: •...
XTP SFR HD 4K Scaling Fiber Receiver series. In this guide, the terms “scaling receiver” and “XTP SFR HD 4K” are used interchangeably to refer to the XTP SFR HD 4K SM Scaling Fiber Receiver or XTP SFR HD 4K MM Scaling Fiber Receiver.
Page 8
The following diagram shows one way the XTP SFR HD 4K can be integrated in an XTP matrix application (see the XTP matrix switcher user guide for more details on matrix applications). Laptop Tuner 1 2 3 Display Volume Tuner...
System Compatibility The XTP SFR HD 4K is compatible with XTP systems, but the maximum video resolution may be limited with different XTP devices. See the table below for maximum video resolutions and refresh rates for various XTP systems. Output...
Page 10
XTP compatibility — Provides a flexible signal switching and distribution solution that is completely integrated, ensuring reliable routing of multiple digital and analog formats. Front panel security lockout — Allows security lockout of front panel buttons except for input selection and volume adjustment. XTP SFR HD 4K Scaling Fiber Receiver • Introduction...
Topics in this section include: Rear Panel Connectors • Connection Details • The XTP SFR HD 4K can be placed on a tabletop or mounted in a rack or under a desk (see Mounting on page 42). Rear Panel Connectors XTP IN...
Page 12
The type of audio present on this output is dictated by the following: The audio format selected on the source material or device. • The source device automatically outputting an audio format through EDID. • XTP SFR HD 4K Scaling Fiber Receiver • Installation...
( ATTENTION: • Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP SFR HD 4K Scaling Fiber Receiver • Installation...
6 for wiring considerations). Smooth Ridges SECTION A–A Power Supply Tie Wrap Output Cord Captive Screw Connector Figure 6. Power Wiring See the notifications on the next page for other considerations. XTP SFR HD 4K Scaling Fiber Receiver • Installation...
Page 15
La longueur idéale est de 5 mm (3/16 inch). Do not tin the stripped power supply leads. Tinned wires are not as secure in the TIP: captive screw connectors and could be pulled out. XTP SFR HD 4K Scaling Fiber Receiver • Installation...
Operation This section contains information for front panel operation and configuration of the XTP SFR HD 4K and configuration through the On-Screen Display (OSD) menu. Topics in this section include: Front Panel Features and Indicators • Rear Panel HDMI Audio Switch •...
Rear Panel HDMI Audio Switch The XTP SFR HD 4K has an HDMI audio switch that mutes or unmutes the embedded figure audio on the HDMI output connector (see on page 5). The LED next to the switch lights when HDMI audio is enabled.
Press the button to cancel any Enter Menu pending changes. To exit the OSD menu: While in the list of submenus, press the button to exit the OSD menu. Menu XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Vertical Adjustment contrast (Contrast) of the image. The default value is Detail — Rotate the adjustment knobs to adjust the detail of the image. The default value XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Image size and position • Recall — Rotate the adjustment knobs to select a preset to recall. Save — Rotate the adjustment knobs to select a preset to store the current picture control settings. XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Output format and color bit depth settings are not configurable from the OSD. Output Configuration Commands To configure either setting, use SIS commands (see Input/Output tab page 24) or use the XTP System Configuration Software (see page 35). Figure 12. Output Configuration Submenu XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Page 22
Color bit depth — Shows the color bit depth setting. This is not configurable from the OSD Video bit depth menu. To configure this setting, use SIS commands (see SIS commands Input/Output tab on page 24) or the XTP System Configuration Software (see on page 34). XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Enter buttons simultaneously for about 2 seconds or until the Power LED blinks (see Front Panel Lockout mode XTP System Configuration SIS commands on page 26 or Software on page 28 for remote enabling or disabling of the Front Panel Lockout mode). XTP SFR HD 4K Scaling Fiber Receiver • Operation...
Reset mode (<1 second). Factory values including real-time command on page 27). Default adjustments. The front panel Power LED • blinks four times in quick succession during the reset. XTP SFR HD 4K Scaling Fiber Receiver • Operation...
SIS commands consist of one or more characters per field. No special characters are required to begin or end a command sequence. When the XTP SFR HD 4K determines that a command is valid, it executes the command and sends a response to the host device. All responses from the receiver to the host end with a carriage return and a line feed (CR/LF = ]), which signals the end of the response character string.
Error Responses When the XTP SFR HD 4K receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains invalid parameters, the receiver returns an error response to the host.
Page 27
NOTE: Bypass mode outputs the input signal without being scaled like a standard non-scaling receiver. This prevents higher resolutions from being scaled to a lower resolution and potential input and output sync issues in 3D applications. XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
View brightness View the brightness level. BRIT Brit NOTES: = unmute (default) = Video mute = mute video = mute video and sync X& = default) = Picture adjustment XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
Page 29
Reset shift and size settings to the default values. NOTES: X& = default) = Picture adjustment = Horizontal position or size 65535 = Vertical position or size 65535 XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
= crosshatch = colorbars = greyscale = auto (default) = Video bit depth = 8 bit table See the on page 21. = Output scaler rate and refresh rate XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
= mute S/PDIF and HDMI audio outputs = mute S/PDIF and analog audio outputs = mute all audio outputs X1& in 1 dB steps ( = default) = Volume = User preset XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
1 step = 100 ms or 10 steps = 1 s = Basic mute = default) where 1 step = 100 ms or 10 steps = 1 s = Advanced mute = default) XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
Page 33
= Input signal status = input detected = auto or encrypt the output only when required by = HDCP mode the input (default) = always encrypt the output XTP SFR HD 4K Scaling Fiber Receiver • SIS Configuration and Control...
Configuration Software This section contains installation and configuration procedures for the XTP System Configuration Software. The XTP SFR HD 4K can also be controlled with the OSD menu On-Screen Display Menu System (see on page 11) or SIS commands (see Configuration and Control on page 19).
Open the executable (.exe) file from the save location. Follow the instructions that appear on the screen. By default, the installation creates a directory in the Program Files or Program Files (x86) folder. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Software Operation The XTP SFR HD 4K can be controlled via the XTP Configuration software directly from the figure front panel configuration port (see on page 10) or remotely from a connected XTP matrix switcher. Connection The XTP System Configuration Software opens to the screen.
Backup and Restore Commissioning Report available when directly connected to the device. See an XTP matrix switcher user guide (www.extron.com) for more information on these features. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 38
From the menu, select . The Tools Software Preference Software Preference dialog box opens. Figure 25. Software Preference Dialog Box Click the button. The dialog box closes. Reset XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 39
This option opens the XTP System Configuration Software Help file in a Web browser. From the menu, select Help Help Extron Website This option opens the Extron website in a Web browser. From the menu, select Help Extron Website XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Audio Mute Audio and video mute — Click the button to mute or unmute audio and AV Mute video output. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 41
Test Pattern — From the drop-down list below the test pattern preview, select the figure 14 desired test pattern (see on page 17 for examples of the available test patterns). XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 42
Down Brightness — Adjust the brightness level of the output. Contrast — Adjust the contrast level of the output. Detail — Adjust the detail level of the output. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 43
Enter a value or click the arrows in the Down Horizontal Position fields ( Vertical Position To reset all position and size settings to default values: Click the button ( Image Reset XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 44
DVI signals. NOTE: When this check box is selected, Extron EDID Minder does not show the EDID information of the connected display. It shows a 720p Extron EDID. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 45
General output video and sync. Mute video and sync — Click the button to mute the active Mute Video and Sync video and disable sync on the output. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 46
Factory Reset receiver to factory settings (except for firmware). Reset mode NOTE: This is the same as the SIS command (see the ZXXX command on page 27). XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Page 47
S/PDIF output. ¢ Analog Audio — Displays the mute status of the analog audio output. £ Analog Audio Volume — Displays the analog audio output volume level. XTP SFR HD 4K Scaling Fiber Receiver • XTP System Configuration Software...
Information This section contains mounting information. Mounting The XTP SFR HD 4K can be placed on a tabletop or mounted in a rack or underneath a desk. Tabletop Mounting Attach the provided rubber feet to the bottom four corners of the enclosure.
Page 49
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or itness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Need help?
Do you have a question about the XTP SFR HD 4K and is the answer not in the manual?
Questions and answers