Extron electronics XTP FT HD 4K Setup Manual

XTP FT HD 4K and XTP FR HD 4K • Setup Guide
CLASS 1 LASER PRODUCT,
The XTP FT HD 4K is an XTP
Ethernet transmission over a fiber optic cable. This guide provides instructions for an experienced installer to install and connect
the XTP FT HD 4K and XTP FR HD 4K.

Transmitter Connectors

A DC power connector
HDMI input connector
B
HDMI Loop-thru connector
C
and HDMI audio switch
Analog audio input
D
connector
RS-232 and IR Over XTP
E
connector
XTP output connector
F
LAN connector
G
Figure 1. Rear Panel Connectors

Installation

Step 1 — Mount the Devices
Turn off or disconnect all equipment power sources and mount the transmitter and receiver on a tabletop or in a rack.
Step 2 — Connect Inputs
Connect a digital video source to the female HDMI connector (see figure 1,
a.
an appropriate adapter), or dual mode DisplayPort video signals.
NOTES:
• Use an Extron LockIt
• Video input from a DisplayPort source must be a dual mode DisplayPort source.
Connect a digital video display to the HDMI Loop-thru connector (
b.
display that is not HDCP-compliant displays a green screen when HDCP-encrypted content is sent to it.
Connect balanced or unbalanced stereo audio to the
c.
3.5 mm, 5-pole captive screw connector (
Step 3 — Connect Throughput Devices
Connect a fiber optic cable between the XTP connectors on the transmitter (
a.
WARNING:
Potential risk of severe injury. The XTP FT HD 4K and XTP FR HD 4K output continuous invisible light
(class 1 rated), which may be harmful to the eyes; use with caution.
AVERTISSEMENT :
lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, àutiliser avec précaution.
• Do not look into the fiber optic cable connectors or into the fiber optic cables themselves.
• Ne regardez pas dans les connecteurs de câble fibre optique sur le ou dans les câbles fibre optique euxmêmes.
• Plug the attached dust caps into the optical transceivers when the fiber optic cable is unplugged.
• Branchez la protection contre la poussière dans l'ensemble émetteur/récepteur lorsque le câble fibre optique est
débranché.
Signal LED indicator — Lights green on the transmitter when it is transmitting a video signal or test pattern. Lights green on
the receiver when it receives an active XTP input signal from a transmitter or matrix switcher.
Link LED indicator — Lights yellow when a valid link between an XTP input and output is established.
see the XTP FT HD 4K and XTP FR HD 4K User Guide at
transmitter and the XTP FR HD 4K is an XTP receiver for video, audio, bidirectional control, and
®

Receiver Connectors

H DC power connector
XTP input connector
I
LAN connector
J
K RS-232 and IR Over XTP
connector
HDMI output connector and
L
HDMI audio switch
Analog audio output connector
M
S/PDIF audio output connector
N
Relay connectors
O
lacing bracket to secure HDMI cables to the rear panel connectors.
®
D ).
Sleeves
Risque potentiel de blessure grave ou de mort. Le XTP FT HD 4K et XTP FR HD 4K émet une
A B
INPUTS
POWER
12V
1.0 A MAX
XTP FT HD 4K
HDMI
XTP FT HD 4K
H I
XTP IN
POWER
12V
1.0 A MAX
SIG LINK
XTP FR HD 4K
B ) on the transmitter. It accepts HDMI, DVI (with
) on the transmitter to locally display the input source. A
C
Tip
Ring Tip
Sleeve
Tip
Tip
Sleeve
Ring
Balanced Stereo Input
) and receiver (
F
.
www.extron.com
C D E F
OVER XTP XTP OUT
AUDIO
AUDIO
RS-232 IR
L R
ON
OFF
LOOP THRU
Tx Rx G Tx Rx SIG
J K L M N O
OVER XTP OUTPUTS
AUDIO AUDIO
RS-232 IR
ON L R
OFF
HDMI S/PDIF
LAN Tx Rx G Tx Rx
Do not tin the wires!
Unbalanced Stereo Input
).
I
G
RESET
LINK LAN
XTP FR HD 4K
RELAYS
1 2
RESET
1