Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Setup Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Extron electronics XTP FT HD 4K
Summary of Contents for Extron electronics XTP FT HD 4K
- Page 1 User Guide Fiber Optic XTP FT HD 4K XTP FR HD 4K XTP Fiber Optic Transmitter and Receiver 68-2201-01 Rev. A 09 15...
-
Page 2: Safety Instructions
Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан alert the user of the presence of uninsulated dangerous voltage within the на... - Page 3 This interference must be corrected at the expense of the user. Class 1 Laser Product Any service to this product must be carried out by Extron Electronics and its qualified service personnel. NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and...
- Page 4 Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: Potential risk of severe injury or death. AVERTISSEMENT: Risque potentiel de blessure grave ou de mort. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.
-
Page 5: Table Of Contents
Host-to-Device and Device-to-Host Communication ........... 16 Error Responses ........... 16 Using the Command and Response Tables for SIS Commands ........17 Symbol Definitions ........17 XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Contents... - Page 6 XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Contents...
-
Page 7: Introduction
XTP FT HD 4K Fiber Optic Transmitter and XTP FR HD 4K Fiber Optic Receiver. In this guide, the terms “XTP FT HD 4K” and “transmitter” refer to the XTP FT HD 4K Fiber Optic Transmitter. The terms “XTP FR HD 4K” and “receiver” refer to the XTP FR HD 4K Fiber Optic Receiver. - Page 8 The following diagram shows some ways the XTP FT HD 4K and XTP FR HD 4K can be integrated in an XTP matrix application. Laptop Tuner 1 2 3 Display Volume Tuner Channel Presets Ethernet Mute Mute House Room Last...
-
Page 9: System Compatibility
System Compatibility The XTP FT HD 4K and XTP FR HD 4K are compatible with XTP matrix systems, but the maximum video resolution may be limited with twisted pair models. Outputs from Receivers or Matrix Switchers non-4K 4K Fiber Analog... - Page 10 Receiver selectable HDMI audio pass-through — Enables or disables audio signal pass-through on the HDMI output. Receiver output volume and mute control Receiver relays — Enables control of lighting, screen settings, and other device functions. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Introduction...
-
Page 11: Installation
13 to select local audio output options). A display that is not HDCP-compliant displays a green screen when HDCP encrypted content is sent to it. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... - Page 12 AVERTISSEMENT: Risque potentiel de blessure grave ou de mort. Le XTP FT HD 4K émet une lumière invisible en continu qui peut être dangereux pour les yeux, à utiliser avec précaution.
-
Page 13: Xtp Fr Hd 4K Rear Panel Connectors
“IR” and shares the ground pole with the RS-232 port. RS-232 and IR NOTE: RS-232 and IR data can be transmitted simultaneously (see Communication on page 10 for wiring details). XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 14: Receiver Relay
2-pole captive screw connector (see figure on page 7). For wiring considerations, see Power Connection on page 11. The Power LED lights to indicate the device is receiving power. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 15: Connection Details
Connect and pull the tie wraps until they are secure. Do not overtighten. • Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas trop serrer. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 16: Rs-232 And Ir Communication
Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws. • S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 17: Power Connection
Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical Code, partie 1, section 16. La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 18: Operation
Audio Signal Clip LED indicator — Lights when the analog audio input signal remains above -3 dBFS. The LED remains lit for 200 milliseconds after the signal falls below -3 dBFS. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 19: Xtp Fr Hd 4K Front Panel Features
Analog LED indicator — Lights when the input audio format is LPCM-2Ch. HDMI Audio Switch The XTP FT HD 4K and XTP FR HD 4K have an HDMI audio switch AUDIO that mutes the embedded audio on the related HDMI connector. On the XTP FT HD 4K, the audio switch mutes or enables the audio on the HDMI loop-thru connector. -
Page 20: Edid
NOTE: In matrix applications, EDID on the transmitter is assigned by the matrix switcher using the XTP System Configuration Software. The XTP FT HD 4K can record and save EDID in a user memory location on the transmitter. EDID can come from the loop-through display on the transmitter or the output display on the receiver. -
Page 21: Reset Modes
IP settings and real-time Reset mode adjustments. command on page 21). • The front panel Power LED blinks four times in quick succession during the reset. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Installation... -
Page 22: Sis Configuration And Control
Use a computer running the HyperTerminal or Extron DataViewer utility, or a control system to make serial control of the transmitter and receiver possible. To connect directly to an XTP FT HD 4K or XTP FR HD 4K, connect the computer to the front panel USB configuration port. -
Page 23: Using The Command And Response Tables For Sis Commands
ASCII to Hexadecimal Conversion Symbol Definitions = Carriage return and line feed = Carriage return with no line feed • = Space = Escape key XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control... - Page 24 4K (3840x2160) with 2Ch audio HDMI 4K (3840x2160) with Multi-Ch audio HDMI User assigned User assigned User assigned User assigned * = default XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control...
-
Page 25: Command And Response Tables For The Transmitter Sis Commands
= Audio level = unmute (default) = Audio mute = mute loop-through audio EDID Emulation Table See the on page 18. = EDID emulation XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control... -
Page 26: Advanced Configuration Commands
= Black signal resolution = 720p @ 60 Hz (default) = 1080p @ 60 Hz = off = HDCP authorized device status = on (default) XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control... - Page 27 = HDCP-compliant source connected = non-compliant source = video or TMDS signal not detected = Video signal status = video or TMDS signal detected XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control...
-
Page 28: Command And Response Tables For The Receiver Sis Commands
= Audio mute = mute all = relay 1 = Relay number = relay 2 in 16 ms increments 65,535 = Pulse time XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control... - Page 29 = sink detected with HDCP encryption = video or TMDS signal not detected = Video signal status = video or TMDS signal detected XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • SIS Configuration and Control...
-
Page 30: Xtp System Configuration Software
Follow the on-screen instructions. By default, the installation creates a directory in the appropriate Program Files folder named “Extron Electronics\XTP System Configuration.” XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software... -
Page 31: Software Connection
Software Connection The XTP FT HD 4K and XTP FR HD 4K can be controlled directly from the front panel configuration port (see figure on page 12 or figure on page 13) or remotely from an XTP matrix switcher (see the XTP matrix switcher user guide for connection details from an XTP matrix switcher). - Page 32 (see mode 5 in Reset Modes on page 15). NOTE: This is the same as the SIS command (see Reset mode ZXXX page 21). XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software...
- Page 33 Audio only — Displays whether only audio is sent to outputs. Analog Audio Gain — Displays the gain for analog audio. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software...
- Page 34 Open Available pane ( EDID Assign the EDID file from the pane to import the EDID setting to the Available EDID device. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software...
- Page 35 EDID settings common among the selected Common Timings outputs. Select the desired common EDID setting. The EDID will be shown in the Available pane. EDID XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software...
-
Page 36: Receiver Configuration
Force analog audio output — For connected DVI displays, click the Force analog check box to output analog audio. audio output when DVI display is connected XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software... - Page 37 Analog Audio — Displays the mute status of the analog audio output. Analog Audio Volume — Displays the analog audio output volume level. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • XTP System Configuration Software...
-
Page 38: Reference Information
• Updating Firmware with Firmware Loader Mounting The XTP FT HD 4K and XTP FR HD 4K can be placed on a tabletop or mounted in a rack or underneath a desk. Tabletop Mounting Attach the provided rubber feet to the bottom four corners of the enclosure. -
Page 39: Updating Firmware With Firmware Loader
Updating Firmware with Firmware Loader To upload and update firmware for the XTP FT HD 4K and XTP FR HD 4K, download the new firmware to a connected computer and upload the firmware with the Firmware Loader utility. Downloading Extron Firmware Loader Figure 19. -
Page 40: Installing Firmware Loader
Click the link to the right of the desired product. Download Submit any required information to start the download. Note where the file is saved. XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Reference Information... -
Page 41: Installing Firmware With Firmware Loader
Begin Close Firmware Loader when the field shows , the Remaining Time 00.00.000 Progress column is , and the field displays 100% Status complete XTP FT HD 4K Fiber Transmitter and XTP FR HD 4K Fiber Receiver • Reference Information... - Page 42 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Need help?
Do you have a question about the XTP FT HD 4K and is the answer not in the manual?
Questions and answers