Canon iPF8400S Service Manual page 286

Chapter 8
Code
(last 4 digits)
2409 Paper position is not
suitable for
borderless printing.
Check paper position.
Print to normal printing.
Stop printing.
240A Borderless printing is
not possible. Check
supported paper.
Check paper position.
Print to normal printing.
Stop printing.
2500 Ink tank is empty.
to Press OK and
250C replace ink tank.
No ink left.
Replace ink tank.
2510 Ink level is
to unknown.
251C Check ink level.
Press Online to start
printing.
2520 No ink tank
to loaded.
252C Press OK and
check ink tank.
No ink tank
loaded.
Check ink tank.
2540 Ink tank error.
to Press OK and
254C replace ink tank.
Wrong ink tank.
Replace ink tank.
Wrong ink tank.
Press OK and
replace ink tank.
2560 Ink tank error.
to Press OK and
256C replace ink tank.
8-10
Panel display Panel display
(Large LCD) (Small LCD)
No Ink Left
(lower arrow)
Online Key
Press To Print
Ink Lvl Unknown
Press Online
Ink Tank
Check XX
No Ink Tank
Check Ink Tank
Ink Tank
Replace BK
Ink Tank Error
Repl. Ink Tank
Ink Tank
Replace BK
Ink Tank Error
Repl. Ink Tank
Explanation/Detection sequence
Invalid paper loading position (suspended
job/ borderless printing)
All of the following conditions were met.
-Borderless printing data has been
received.
-Roll paper whose paper loading position is
not suitable for borderless printing has
been loaded.
-The right or left edge of roll paper is more
than 1mm off the prescribed position of the
pre-ejection opening.
Borderless printing is not possible
(suspended job/ unsupported size). All of
the following conditions are met.
-Borderless printing data has been
received.
-Roll paper not supporting borderless
printing has been loaded.
Ink tank empty (continued use not allowed)
The ink tank has run out of ink. (The
reserved volume of ink is put to use after
the remaining ink falls below the pin check
level.)
(In the small LCD, the lower arrow points
to the color in question.)
The last 2 digits signify applicable colors.
00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC,
06:MBk1,
07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B,
0C:G
Remaining ink level unknown (continued
use allowed)
The level of ink remaining in the tank is
detected when the tank cover is closed.
Consumption has exceeded the original ink
capacity (mismatch detected).
Refill ink may have been used.
(In the small LCD, the lower arrow points
to the color in question.)
The last 2 digits signify applicable colors.
10:Bk, 11:Y, 12:M, 13:C, 14:PM, 15:PC,
16:MBk1,
17:MBk2, 18:GY, 19:PGY, 1A:R, 1B:B,
1C:G
Ink tank not installed (continued use not
allowed)
On a model that is furnished with a
subtank, this error is indicated if the
subtank has run out of ink and the state of
an ink tank not being installed is detected.
The last 2 digits signify applicable colors.
20:Bk, 21:Y, 22:M, 23:C, 24:PM, 25:PC,
26:MBk1,
27:MBk2, 28:GY, 29:PGY, 2A:R, 2B:B,
2C:G
Ink tank ID error
The type of ink tank is wrong.
The last 2 digits signify applicable colors.
40:Bk, 41:Y, 42:M, 43:C, 44:PM, 45:PC,
46:MBk1,
47:MBk2, 48:GY, 49:PGY, 4A:R, 4B:B,
4C:G
Ink tank EEPROM error
There is an error in tank EEPROM.
The last 2 digits signify applicable colors.
60:Bk, 61:Y, 62:M, 63:C, 64:PM, 65:PC,
66:MBk1, 67:MBk2, 68:GY, 69:PGY,
6A:R, 6B:B, 6C:G
Remedial Action
Reload/ replace the roll paper.
Check roll paper.
1) Select "Normal printing. (No
borderless printing)" and enforce
printing.
Borderless print setting is ignored.
Print with default margin.
Default margin depends on selected
feeding trays and media type.
2) Select "Stop printing" or press "stop
button"to stop printing.
3) Select "replace printing" or release
releasing lever.
1. Replace the tank.
2. If the problem persists after the tank
has been replaced, the remaining ink
detection system is at fault (replace the
supply unit or check the bundled
wires).
Replace the ink tank.
1. Remove and then reinstall the tank.
2. Replace the tank.
3. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
1. Replace the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
1. Replace the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)