Acura 3.5 RL Manual page 1192

Driving Position Memory System (DPMS)
Power Mirror Control Unit Input Test (cont'd)
12P CONNECTOR "A"
BLU/GRN
LT GRN/RED
BLK/WHT
Cavity Wire
Connect battery power
B3
BRN
to the B3 terminal, and
• •
B4 terminal to the B9
YEL
B4
terminal momentarily.
Connect battery power
BRN
B3
to the B3 terminal, and
• •
B12 terminal to the B9
B12 BLU
terminal momentarily.
Connect battery power
YEL
B2
to the B11 terminal, and
• •
B2 terminal to the B9
B11 BRN
terminal momentarily.
Connect battery power
B10 BLU
to the B11 terminal, and
•
*
B10 terminal to the B9
BRN
B11
terminal momentarily.
Reconnect all connectors to the power mirror control unit.
Cavity Wire
Ignition switch ON (II)
B8 RED/BLK
NOTE: Connect all
• •
mirror control unit
BRN/WHT
B16
connectors.
Ignition switch ON (II)
B7 GRN NOTE: Connect all
mirror control unit
•
•
connectors.
B16 BRN/WHT
Ignition switch ON (II)
NOTE: Connect all
B15 GRY
mirror control unit
• •
connectors.
B16 BRN/WHT
Ignition switch ON (II)
GRN/WHT NOTE: Connect all
B6
mirror control unit
•
•
connectors.
BRN/WHT
B16
Ignition switch ON (II)
B14 GRY NOTE: Connect all
mirror control unit
• •
BRN/WHT connectors.
B16
BLU/ORN
RED/WHT
WHT/YEL
BLK
YEL BLU
YEL/BLK
Test condition
Check the right power mirror
actuator operation:
The mirror should swing left.
Check the right power mirror
actuator operation:
The mirror should tilt down.
Check the left power mirror
actuator operation:
The mirror should swing left.
Check the left power mirror
actuator operation:
The mirror should tilt down.
Test condition
Check for voltage between the
terminals:
There should be about 5 V.
Check for voltage between the
terminals:
The voltage should change from
about 1 V to 3 V when the right
mirror swings from left to right.
Check for voltage between the
terminals:
The voltage should change from
about 1 V to 3 V when the right
mirror tilts from up to down.
Check for voltage between the
terminals:
The voltage should change from
about 1 V to 3 V when the left mir-
ror swings from right to left.
Check for voltage between the
terminals:
The voltage should change from
about 1 V to 3 V when the left mir-
ror tilts from up to down.
16P CONNECTOR "B"
RED/YEL
BLK
Test: Desired result
Test: Desired result
GRN
BRN
YEL GRN/WHT
RED/BLK
YEL
BRN
GRY
BLU BLU GRY
Possible cause if result is not obtained
• Faulty right power mirror actuator
• An open in the wire
• Faulty right power mirror actuator
• An open in the wire
• Faulty left power mirror actuator
• An open in the wire
• Faulty left power mirror actuator
• An open in the wire
Possible cause if result is not obtained
• Faulty power mirror position
sensors
• An open in the wire
• Faulty right power mirror position
sensor
• An open in the wire
• Faulty right power mirror position
sensor
• An open in the wire
• Faulty left power mirror position
sensor
• An open in the wire
• Faulty left power mirror position
sensor
• An open in the wire
BRN/WHT